• Progress in Superconductivity and Cryogenics
• /
• v.6 no.1
• /
• pp.1-5
• /
• 2004

Long length of Bi-2223/Ag superconducting wives were fabricated by stacking and drawing process with advanced heat-treatment schedules. Intermediate annealing was carried out to increase the homogeneity and uniformity of the superconducting filaments embedded in the silver matrix. Phase modification from tetragonal to orthorhombic Bi-2212 by pre heat treatment(PHT) was executed to improve the texture and phase transformation of Bi-2223. Drawing stress was measured to predict the sausaging and stress limit. Rolling Parameters such as thickness. width and winding tension were investigated to roll the tape with uniformity. 1 km length of Bi-2223/Ag superconducting wires were fabricated without any breakage. Critical current (Je) of 270 m length of superconducting tapes was measured over than $70 A/cm^2$ continuously after final sintering.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.144-150
• /
• 2000

In this paper, the formation of a corner cavity in the final stage of axisymmetric backward extrusion process is studied by means of upper bound analysis using kinematically admissible velocity. The quantitative relationships between corner cavity formation and process parameters are studied. And analytical results are compared with those of experiment to which plasticine is used. It is found that the analytical results agree well with experimental one. In addition, to restrict the formation of a corner cavity, driven container is applied to backward extrusion and the results are compared with those of FEM. The critical thickness of the bottom of the billet decreases with increase in reduction of area, and increases with decrease in friction. To prevent the formation of corner cavity, the concept of moving container was applied. Throughout this process, the occurrence of a corner cavity is delayed and forming limit area is enlarged.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1360-1363
• /
• 1996

EPD(End Point Detection) is used to decide etching degree of layer which must be removed at wafer etching process in plasma etching process which is one of the most important process in semiconductor manufacturing. In this thesis, the method which detects malfunction of etching process in real-time will be discussed. Several EPD signal traces are collected in normal plasma etching condition and used as reference EPD signal traces. Critical points can be detected by applying differentiation and zero-crossing techniques to reference EPD signal. Mean and standard deviation of critical parameters which is memorized from reference EPD signal are calculated and these determine the lower and higher limit of control chart. And by applying statical control chart to EPD signals which are collected in real etching process malfunctions of process are detected in real-time. By means of applying this method to the real etching process we prove our method can accurately detect the malfunction of etching process and can compensate disadvantage of current industrial method.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.565-573
• /
• 2004

This study is to present explicit analytical expressions for calculating bearing capacity factor $N_{\gamma}$, to provide results of the numerical computation instead of the graphical method. In this study, $N_{\gamma}$ is proposed in the critical failure surface on assumption that the center of log spiral in the radial shear zone can be located at the any points of around footing. The critical failure surface is one which yields minimum passive pressure $P_{\gamma}$ on the radial shear zone from the family of log spirals accoding to change of the center of log spiral. This study adoptes Terzaghi's bearing capacity principle(e.g., Prandtl's mechanism, limit equilibrium equation, superposition principle) but the soil wedge in an elastic zone makes angle $45^{\circ}+{\phi}/2$ with the horizontal and the location of the log spiral's center.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.609-611
• /
• 1999

The purpose of this research is on figuring out the optimal PID parameter using critical gain and critical frequency that are obtained by relay feedback. The operating has been done under the condition that the least information about the object plant is given and also the operating is processed within the limit which dose not give rise to bad influence on the object plant. For simulation auto-tuning PID controller using relay feedback which also works on on-line at the same time is developed by the upper procedure. This algorithm is tried to apply to level-temperature control plant on a real time with PC Interface Card.

• Journal of Korean Association for Spatial Structures
• /
• v.12 no.3
• /
• pp.55-62
• /
• 2012

본 연구는 온도 증가에 따른 압축을 받는 H형 강재의 플랜지와 웨브의 국부 및 전체좌굴응력 내화해석 프로그램 개발과 플랜지와 웨브가 항복파괴전에 국부좌굴이 일어나지 않을 한계 판폭두께비의 상관값을 구하는 프로그램을 개발하는 것이다. 고온에서의 강재의 응력-변형도 관계식은 EC3:Part 1.2를 근거로 하였으며, 비교, 검토를 위하여 영국 BS5950의 강재를 대상으로 온도 증가에 따른 압축을 받는 강재의 플랜지와 웨브의 파괴온도와 하중을 본 연구의 내화해석 프로그램으로 예측하였다. 본 연구는 좌굴 및 항복에 대한 내화해석 프로그램을 개발하는 것을 목적으로 하고 적용 예를 통하여 좌굴 및 한계 판폭두께비를 분석하고 개발 프로그램의 타당성을 검토하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.140-146
• /
• 2002

High speed rotating machines can be very sensitive to rotating mass unbalance that is a major source of harmful vibration for many types of rotating machinery. So, the balancing procedure is needed for all high-speed rotating system. To save the time and cost of off-line balancing, many researchers have developed the on-line balancing devices and methods. In this paper, an active balancing device, which is an electro-magnetic type, is developed and the active balancing algorithm using influence coefficient method is also proposed. The active balancing experiment for flexible rotors during operation is performed by an active balancing device. As a result, controlled unbalance responses are below the vibration limit at all rotating speed ranges with critical speed.

• Progress in Superconductivity and Cryogenics
• /
• v.15 no.2
• /
• pp.29-33
• /
• 2013

The understanding of the strain dependence of critical current, $I_c$, in the reversible region is important for the evaluation of the performance of coated conductor (CC) tapes in practical applications. In this study, the stress/strain tolerance of $I_c$ in GdBCO CC tapes with stainless steel substrate stabilized by additional Cu and brass laminate was analyzed quantitatively through $I_c$-strain measurement at 77 K under self-field. The variation in irreversible strain limits of CC tapes by the addition of stabilizing layers was analyzed through the consideration of the pre-strain induced on the GdBCO coating film. The results were then compared with the ones previously reported for GdBCO CC tapes with Hastelloy substrate. As a result, GdBCO CC tapes with stainless steel substrate showed much higher strain tolerance of $I_c$ as compared with those adopting Hastelloy substrate.

• Korea-Australia Rheology Journal
• /
• v.20 no.4
• /
• pp.197-211
• /
• 2008

The purpose of this study is mainly directed towards present of viewpoints on critical and commentary analysis on blood rheology, blood viscosity models, and physiological flow conditions. Understanding these basics is fundamental to meet the need for a sufficient and reliable CFD model of blood. Most of the used viscosity models on this manner have determined from parameter fitting on experimental viscosity data. Availability of experimental data from literature to define viscosity models of CFD analysis should be accurately chosen and treated in order to avoid any errors. Several basic gaps that limit the CFD model results are identified and given opportunities for future research.

• Journal of Families and Better Life
• /
• v.19 no.5
• /
• pp.279-291
• /
• 2001

This study was peformed to identify a credit limit of the household. For this purpose, the differences in household economy by debt burden and the effects of debt burden on household economy was analyzed with the data of the Family Income and Expenditure Survey in 1999. The results showed that the household with debt burden, are likely to cut savings not consumption expenditures. The critical level of debt burden which distorts the household economy is found to be 25%. If the debt burden of the household exceeds 25%, they are no longer to save and ought to borrow to repay current debt.