• Computers and Concrete
• /
• 제9권4호
• /
• pp.311-325
• /
• 2012

In this paper, we examine the behavior of the High-Rate Brittle Microplane (HRBM) concrete model based on a series of penetration experiments. These experiments were conducted with three different slab thicknesses (127, 216 and 254 mm) that provided a significant challenge for the numerical simulations. The 127 mm slab provided little resistance, the 216 mm slab provided nominal resistance and the 254 mm slab approached the perforation limit thickness of the projectile. These experiments provide a good baseline for evaluating material models since they have been shown to be extremely challenging; in fact, we have not encountered many material models that can provide quantitatively predictive results in terms of both projectile exit velocity and material damage. In a companion paper, we described the HRBM material model and its fit to various quasi-static material property data for WES-5000 concrete. In this paper, we show that, when adequately fit to these quasi-static data, the HRBM model does not have significant predictive capabilities, even though the quasi-static material fit may be exceptional. This was attributed to the rate-dependent response of the material. After various rate effects were introduced into the HRBM model, the quantitative predictive nature of the calculations dramatically increased. Unfortunately, not much rate-dependent material property data are in the literature; hence, accurate incorporation of rate effects into material models is difficult. Nonetheless, it seems that rate effects may be critical in obtaining an accurate response for concrete during projectile perforation events.

• 제어로봇시스템학회논문지
• /
• 제15권9호
• /
• pp.877-880
• /
• 2009

A curing process in post-printing section of R2R process is required for an electrical property of the printed pattern when devices such as RFID, Solar cell are printed. PEN as well as heat-stabilized PET which is used as a plastic substrate would be deformed at high temperature due to change of its elastic modulus. And crack in the printed pattern, which is on the plastic substrate is occurred due to the deformation of the substrate. The occurrence of crack causes electrical resistance to increase and the quality of the device to deteriorate. In case of RFID antenna, the range of reading distance is shortened as the electrical resistance of the antenna is increased. Therefore, the deformation of the plastic substrate, which causes the occurrence of crack, should be minimized by setting up low operating tension in R2R process. In low tension, slippage between a moving substrate and a roller would be generated when the operating speed is increased. And scratch would be occurred when slippage is generated due to an air entrainment, which is related to the thickness of the air film. The thickness of the air film is increased when operating speed is increased as shown by simulation based on mathematical model. The occurrence of scratch in conductive pattern printed by roll to roll process is a critical damage because it causes degradation or failure of electrical property of it.

• Imaging Science in Dentistry
• /
• 제37권2호
• /
• pp.69-77
• /
• 2007

Purpose: To evaluate the accuracy of the imaging reformation of cone beam computed tomography for the assessment of bone defect healing in rat model. Materials and Methods: Sprague-Dawley strain rats weighing about 350 gms were selected. Then critical size bone defects were done at parietal bone with implantation of collagen sponge. The rats were divided into seven groups of 3 days, 1 week, 2 weeks, 3 weeks, 4 weeks, 6 weeks, and 8 weeks. The healing of surgical defect was assessed by multi planar reconstruction (MPR) images and three-dimensional (3-D) images of cone beam computed tomography, compared with soft X-ray radiograph and histopathologic examination. Results: MPR images and 3-D images showed similar reformation of the healing amount at 3 days, 1 week, 2 weeks, and 8 weeks, however, lower reformation at 3 weeks, 4 weeks, and 6 weeks. According to imaging-based methodologies, MPR image revealed similar reformation of the healing amount than 3-D images compare with soft X-ray image. Among the four threshold values for 3-D images, 400-500 HU revealed similar reformation of the healing amount. Histopathologic examination confirmed the newly formed trabeculation correspond with imaging-based methologies. Conclusion: MPR images revealed higher accuracy of the imaging reformation of cone beam computed tomography and cone beam computed tomography is a clinically useful diagnostic tool for the assessment of bone defect healing.

• 한국균학회지
• /
• 제44권3호
• /
• pp.193-195
• /
• 2016

한국의 인삼(Panax ginseng)은 다양한 생리학적, 약리학적 활성을 지닌 것으로 입증되어 왔다. 인삼 잘록병은 Rhizoctonia solani와 Pythium sp.과 같은 식물 병원균에 의해 발생하며 인삼 종자에 치명적이다. 잘록병은 일반적으로 화학농약을 이용하여 방제하고 있다. 또한 생물학적 방제는 인삼 잘록병을 방제하는데 효과적이며 환경친화적인 방법으로 알려져 있다. 본 연구진은 인삼 잘록병 방제를 위한 생물 방제제로서 잠재성을 지닌 토양 세균을 탐색하였으며, 그 결과 항균물질 guanidylfungin과 methylguanidylfungin을 생산하는 방선균 A3265 균주를 선발하였다. 본 연구는 방선균 A3265 균주의 인삼 잘록병 방제 활성을 포장에서 조사한 것이다. 그 결과 인삼종자를 방선균 A3265 균주의 배양액에 침지한 후 파종하였을 때 잘록병의 발병률이 유의적으로 감소함을 확인하였다. 이는 방선균 A3265 균주가 잘록병 방제에 효과적으로 활용될 수 있음을 나타낸다.

• 생명과학회지
• /
• 제13권6호
• /
• pp.814-821
• /
• 2003

Heme 합성의 중간체이며 또한 광수용체로도 작용하는 protoporphyrin IX의 세포 내 농도 및 성장 배지에 존재하는 농도가 야생형 M. xanthus DK1622 균주로부터 측정되었다. Protoporphyrin IX의 세포 내 농도는 배양 시간이 경과함에 따라 계속 증가하여, 안정기에 최고치에 이르는 것으로 나타났다 안정기에 도달한 세포 내에는 6.4 picomoles/mg of protein의 protoporphrin IX이 존재하는 것으로 밝혀졌다. Protoporphyrin IX은 대수기 중간 시기부터 세포외로 분비가 시작되어, 안정기에 도달한 세포의 배양액에서는 세포의 단백질 대비하여 3.0 picomoles/mg of protein이 존재하는 것으로 측정되었다. 영양분의 고갈에 기인하여 형성된 포자에서도 protoporphyrin IX의 농도는 6.5 picomoles/mg of protein이 존재하는 것으로 관찰되었다. Succinylacetone을 $500\muM$ 농도로 성장 배지에 첨가하였을 경우에 protoporphyrin IX의 생산은 검출이 불가능할 정도로 방해를 받았으며, 세포성장이 저해되고 세포 성장은 정상의 절반 수준인 약 100 Klett unit에서 정지하는 것으로 나타났다. 하지만 포자의 형성은 succinylacetone의 첨가에 관계없이 89-100%의 생성율을 보였음으로 정상 농도의 protoporphyrin IX가 M. xanthus의 성장을 위해서는 중요하지만, 포자 형성 과정에 필수적인 것으로 보이지는 않는다. 안정기 세포에서 나타나는 photolysis 현상도 succinylacetone의 첨가 여부에 관계없이 유사한 수준으로 관찰되었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권4호
• /
• pp.24-27
• /
• 2012

The measurement of the coefficient of thermal expansion (CTE) of polypropylene laminated paper (PPLP) as electric insulating material is important for its practical superconducting device application. The thermal strain induced to HTS tapes and its insulating material during cooling from room temperature might largely affect the critical current ($I_c$) of HTS tapes. In this study, the thermal contraction of PPLP material was measured during cooling from 300 K to 77 K using double extensometers. Initially, the CTE of a brass tape was measured and it was compared with a reference data. It was found that the measured thermal expansion data of the brass material approaches that of the reference one. Based on the results, it was then confirmed that the measurement technique could be applied to thin and flexible samples. Therefore, the same measurement procedure was applied to PPLP material using double extensometers. As a result, the linear CTE of the PPLP at 77 K has been measured to be ${\sim}15.3{\times}10^{-6}/K$. Also, it was found that the thermal contraction characteristics of PPLP was dominated by polypropylene on the cross direction (higher thermal contraction) while it was dominated by Kraft paper on the machine direction (lower thermal contraction). Overall, this measurement procedure could be adopted for the determination of CTE of flexible materials such as PPLP.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.335-340
• /
• 2002

In recent years, the study of metal matrix composite has increased specially, aluminum alloy, research and development are briskly progress to find new metal matrix composite. this study is following the this purpose; This study is used metal matrix composite that was produced by matrix, AC4CH. and reinforcement $A_{18}B_4O_{33}$ metal matrix composite to add $Al_2O_3,\;TiO_2$ for strengthen of binding together among the Whisker. Each Metal matrix composite is produced using the squeeze casting method. Fracture tounghness test was in accordance with the provisions of ASTM E399; Specimen was produced half-size CT specimen W=25mm, B=12.5mm, Cross head speed 0.05mm/min in room temperature. The plane strain fracture toughness $K_{IC}$ is $8.7MPa-m^{0.5}$ for $Al_{18}B_4O_{33}$/AC4CH., $9.28MPa-m^{0.5}$ for $Al_{18}B_4O_{33}$/AC4CH added $TiO_2$. and $Al_2O_3$ but AC4CH alloy was violated the critical stipulated by ASTM standard for a valid measurement of $K_{IC}$. In case of, it was performed $I_{IC}$ test instead of $K_{IC}$ based on ASTM E 1820

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.373-378
• /
• 2002

Metal matrix composites have a great interest in recent years because high specific strength, high specific stiffness characteristics, and application ranges of the composites are extend to variety industry. In this paper, an investigation was performed on the plane strain fracture toughness and slinding wear properties of AC4CH alloy(Al-Si-Mg line) reinforced with 20wt% aluminum borate whisker expect one, which contained a inorganic binder($TiO_2$). the binder led to the formation of strengthen the whisker each other. The test of fracture toughness was using CT(half size) specimen of thickness 12.5mm, width 25mm. and test of slinding wear of using tribo a pin-on-disk machine and lubricant is used without paraffine 8.2CST at room temperature. As results, Fracture toughness $K_{IC}$ is $8.7MPa-m^{05}$ for ABOw/AC4CH, $9.28MPa-m^{05}$ for ABOw/AC4CH added $TiO_2$. but AC4CH alloy was violated the critical stipulated by ASTM standard for valid measurement of $K_{IC}$. In case of, it was performed $J_{IC}$ test instead of $K_{IC}$ based on ASTM E 1820.

• Transactions on Electrical and Electronic Materials
• /
• 제12권1호
• /
• pp.28-31
• /
• 2011

Transformation behavior and shape memory characteristics of Ti-(45-x)Ni-5Cu-xCr (x=0.5-2.0) alloys have been investigated by means of electrical resistivity measurements, differential scanning calorimetry, X-ray diffraction and thermal cycling tests under constant load. Two-stage B2-B19-B19' transformation occurred in Ti-(45-x)Ni-5Cu-xCr alloys. The B2-B19 transformation was separated clearly from the B19-B19' transformation in Ti-44.0Ni-5Cu-1.0Cr and Ti-43.5Ni-5Cu-1.5Cr alloys. A temperature range where the B19 martensite exists was expanded with increasing Cr content because decreasing rate of Ms (85 K / % Cr) was larger than that of Ms' (17 K / % Cr). Ti-(45-x)Ni-5Cu-xCr alloys were deformed in plastic manner with a fracture strain of 68% ~ 43% depending on Cr content. Substitution of Cr for Ni improves the critical stress for slip deformation in a Ti-45Ni-5Cu alloy due to solid solution hardening.

• 한국강구조학회 논문집
• /
• 제20권4호
• /
• pp.455-467
• /
• 2008

본 연구에서는 열차하중에 의한 아치교량의 처짐, 변형률이력곡선, 진동가속도와 같은 동적거동특성을 파악하기 위하여 동적주행시험을 실시하였다. 동적주행시험의 계측결과는 실 제원을 바탕으로 형상화 된 구조해석모델의 시간이력 및 고유치해석과의 비교를 통해 구조해석모델의 타당성을 검증하는데 이용되었다. 검증된 구조해석모델의 공진 검토결과, 주파수 일치에 의한 공진의 경우 가진 진동수와 고유진동수비가 ${1{\pm}0.04}$의 공진영향범위에서 벗어나도록 하는 것이 필요하다 판단된다. 또한 속도매개변수에 의한 공진의 경우 2차 모드 진동수는 아치교량의 동적거동에 크게 영향을 미치며 아치리브와 관련된 형고비, 라이즈비, 폭, 두께 등의 형상 매개변수 조절을 통해 실 운행속도대역 이상으로 부임계속도를 변화시킴으로서 아치교량의 동적거동을 안정화시킬 수 있었다.