• 콘크리트학회논문집
• /
• 제22권3호
• /
• pp.367-374
• /
• 2010

전이슬래브 시스템은 상부 전단벽 구조로부터 하부 기둥으로 하중을 전달하는 구조시스템이다. 이 시스템은 상당한 두께의 슬래브를 필요로 하므로 비경제적이며, 이 단점은 슬래브내에 중공부를 두어 해결할 수 있다. 그리고 이 시스템은 플랫플레이트 구조로써 기둥-슬래브 접합부 부근의 뚫림전단파괴을 일으키는 취성파괴의 위험이 존재한다. 따라서 중공부를 갖는 전이슬래브 시스템의 뚫림전단 성능은 매우 중요하다. 그러나 현행 기준에서는 중공부를 갖는 슬래브의 뚫림전단성능에 대한 명확한 강도산정 규정이 제시되어 있지 않다. 이 연구에서는 중공 시스템의 뚫림전단강도를 알아보기 위하여 실험적 연구를 수행하였으며, 현행기준 및 기존연구를 토대로 실험체의 전단강도를 예측하였다. 그 결과, 중공시스템의 뚫림전단강도는 기둥면으로부터 위험단면 d/2의 위치와 중공부 중심에서의 위험단면으로 계산된 값 중 작은 값으로 결정되었다. 여기서 강도 계산을 위하여 위험단면의 유효단면적을 사용하여 계산하였다.

• Geomechanics and Engineering
• /
• 제17권2호
• /
• pp.133-143
• /
• 2019

An optimal hydraulic section is critical for irrigated water conservancy in seasonal frozen ground due to a large proportion of water leakage, as investigated by in-situ surveys. This is highly correlated with the frost heave of underlain soils in cold season. This paper firstly derived a practical model for frost heave of clayey soils, with temperature dependent thermal indexes incorporating phase change effect. A model test carried out on clay was used to verify the rationality of the model. A novel approach for optimizing the cross-section of irrigation canals in cold regions was suggested with live updated geometry characterized by three unique geometric constraints including slope of canal, ratio of practical flow section to the optimal and lining thickness. Allowable frost heave deformation and tensile stress in canal lining are utilized as standard in computation iterating with geometry updating while the construction cost per unit length is regarded as the eventual target in optimization. A typical section along the Jinghui irrigation canal was selected to be optimized with the above requirements satisfied. Results prove that the optimized hydraulic section exhibits smaller frost heave deformation, lower tensile stress and lower construction cost.

• 전산구조공학
• /
• 제9권4호
• /
• pp.135-140
• /
• 1996

박벽개단면을 갖는 단일 형강재는 압축재로 될 수 있는데 예를 들면 트러스에서 복재가 이런 경우이다. 이 때에는 부재의 조립 때문에 발생하는 필연적 편심을 구조설계시에는 보통 무시한다. 그러나 편심의 영향은 부재를 설계할 때, 특히 압축부재의 설계에서는 고려되어야 할 사항이다. 비틀림이나 혹은 휨과 비틀림에 의해서 좌굴을 일으키는 압축재의 임계하중은 지배하는 비분방정식의 해를 구함으로써 결정된다. 본 논문에서는 채널([), 등변앵글(L), 리프채널(C)의 편심변화에 따른 내하력을 도표로 나타내기로 한다. 또한 식이복잡하므로 컴퓨터를 이용하여 계산한 후, 그 결과를 SURFER프로그램을 사용하여 그래프로 표시하였다.

• 대한토목학회논문집
• /
• 제33권3호
• /
• pp.865-873
• /
• 2013

본 연구에서는 부식이나 보강재가 고려된 비균일한 두께를 가지는 파이프라인에 대하여 일정한 외압을 받을 때의 탄성 좌굴하중을 이론적으로 산정하였다. 길이가 매우 긴 원통형 쉘 구조물인 파이프라인을 단순한 링 구조물로 가정하였고, 고유함수를 유도하여 좌굴 임계하중을 산정하였다. 또한, 두께 변화와 두께가 감소된 구간의 범위에 따른 변수해석을 수행하였다. 이론식에 의해 산정된 좌굴 임계하중 결과를 유한요소해석 결과와 비교하여 검증하였고, 두 결과는 잘 일치함을 알 수 있었다.

• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1326-1336
• /
• 2018

This paper proposes a numerical approach to predict the critical flashover voltages of air gaps under lightning impulses. For an air gap, the impulse voltage waveform features and electric field features are defined to characterize its energy storage status before the initiation of breakdown. These features are taken as the input parameters of the predictive model established by support vector machine (SVM). Given an applied voltage range, the golden section search method is used to compute the prediction results efficiently. This method was applied to predict the critical flashover voltages of rod-rod, rod-plane and sphere-plane gaps over a wide range of gap lengths and impulse voltage waveshapes. The predicted results coincide well with the experimental data, with the same trends and acceptable errors. The mean absolute percentage errors of 6 groups of test samples are within 4.6%, which demonstrates the validity and accuracy of the predictive model. This method provides an effectual way to obtain the critical flashover voltage and might be helpful to estimate the safe clearances of air gaps for insulation design.

• Steel and Composite Structures
• /
• 제31권6호
• /
• pp.591-600
• /
• 2019

Based on the energy-variational principle, a coupling vibration analysis model of high-speed railway simply supported beam bridge-track structure system (HSRBTS) was established by considering the effect of shear deformation. The vibration differential equation and natural boundary conditions of HSRBTS were derived by considering the interlayer slip effect. Then, an analytic calculation method for the natural vibration frequency of this system was obtained. By taking two simply supported beam bridges of high-speed railway of 24 m and 32 m in span as examples, ANSYS and MIDAS finite-element numerical calculation methods were compared with the analytic method established in this paper. The calculation results show that two of them agree well with each other, validating the analytic method reported in this paper. The analytic method established in this study was used to evaluate the natural vibration characteristics of HSRBTS under different interlayer stiffness and length of rails at different subgrade sections. The results show that the vertical interlayer compressive stiffness had a great influence on the high-order natural vibration frequency of HSRBTS, and the effect of longitudinal interlayer slip stiffness on the natural vibration frequency of HSRBTS could be ignored. Under different vertical interlayer stiffness conditions, the subgrade section of HSRBTS has a critical rail length, and the critical length of rail at subgrade section decreases with the increase in vertical interlayer compressive stiffness.

• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2717-2724
• /
• 2020

Silicon, especially silicon in the form of SiO₂, is a major component of rocks. Final spent fuel storages, which are being designed, are located in suitable rock formations in the Earth's crust. Reduction of the uncertainty of silicon neutron scattering and capture is needed; improved silicon evaluations have been recently produced by the ORNL/IAEA collaboration within the INDEN project. This paper deals with the nuclear data validation of that evaluation performed at the LR-0 reactor by means of critical experiments and measurement of reaction rates. Large amounts of silicon were used both as pure crystalline silicon and SiO₂ sand. The critical moderator level was measured for various core configurations. Reaction rates were determined in the largest core configuration. Simulations of the experimental setup were performed using the MCNP6.2 code. The obtained results show the improvement in silicon cross-sections in the INDEN evaluations compared to existing evaluations in major libraries. The new Thermal Scattering Law for SiO₂ published in ENDF/B-VIII.0 additionally reduces the discrepancy between calculation and experiments. However, an unphysical peak is visible in the neutron spectrum in SiO₂ obtained by calculation with the new Thermal Scattering Law.

• 한국문헌정보학회지
• /
• 제11권
• /
• pp.185-208
• /
• 1984

• 한국초전도ㆍ저온공학회논문지
• /
• 제1권2호
• /
• pp.15-19
• /
• 1999

For large scale applications of high temperature superconductor (HTS) such as transmission cables, motors and generators, long length of flexible HTS conductor is required. Currently, Bi-2223 HTS tape is capable of being fabricated in longer than 100 m length by industrial processes. In this study, we fabricated 100 m 19 filamentary Bi-2223 ($Bi_{1.8}Pb_{0.4}Sr_2Ca_2O_{10+x}$) HTS tape by PIT (Power in Tube) process. Critical current(IC) of this long length tape was measured 18.5 A at 77K, self field. Critical current of 100 m length tape was mainly resulted from the increase of inhomogeneity in oxide from the increase of inhomogeneity in oxide layer. Engineering critical current (Je=Ic/total tape cross-section area) that is important factor for practical applications and fabrication cost was measured 2.2 kA/cm2.

• 한국정밀공학회지
• /
• 제12권6호
• /
• pp.112-119
• /
• 1995

Early fracture and cutting force of ceramic tool for hardened STC3 steel was investigated in this study. It was found that early fracture of ceramic tool was mostly occurred before normal wear was progressed beyond a critical cutting speed and normal wear was performed under the critical cutting speed. The relationships among critical cutting speed, which was a cause of early fracture, suggested cutting cross section, that is, maximum thickness of cut and width of cut, and cutting force were examined. The following conclusions were obtained: (1)Critical cutting speed showed a high value in the case of small maximum thickness of cut and large nose radius, but was not influenced by width of cut, (2)Principal, feed and radial force, respectively, showed the proportional value to constant cutting area, width of cut and maximum thickness of cut orderly, (3)Occurrence of early fracture was dependent upon radial force.