• Progress in Superconductivity
• /
• v.13 no.3
• /
• pp.169-177
• /
• 2012

Distribution of the local properties in GdBCO and YBCO coated conductors was investigated using Low-temperature Scanning Laser and Hall Probe Microscopy (LTSLHPM). We prepared GdBCO and YBCO coated conductors to study the spatial distribution of the current density in a single bridge. Inhomogeneity of the ${T_c}^{max}$ in the bridge was analyzed from experimental results of Scanning Laser Microscopy (SLM) near the superconducting transition. The local transport and screening current in the bridge were also investigated using Scanning Hall Probe Microscopy (SHPM). A series of line scans of SLM of the GdBCO and YBCO sample showed that lines with more inhomogeneous distributions of ${\delta}V$ had more inhomogeneous distributions of ${T_c}^{max}$. The defect of the superconducting layer of the GdBCO sample caused by damage to the substrate affected the current flow. And we could analyze the redistribution of the current density using SLM and SHPM.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1598-1600
• /
• 2003

Microcrystalline silicon(c-Si:H) thin-film solar cells are prepared with intrinsic Si-layer by hot wire CVD. The operating parameters of solar cells are strongly affected by the filament temperature ($T_f$) during intrinsic layer. Jsc and efficiency abruptly decreases with elevated $T_f$ to $1400^{\circ}C$. This deterioration of solar cell parameters are resulted from increase of crystalline volume fraction and corresponding defect density at high $T_f$ The heater temperature ($T_h$) are also critical parameter that controls device operations. Solar cells prepared at low $T_h$ (<$200^{\circ}C$) shows a similar operating properties with devices prepared at high $T_f$, i.e. low Jsc, Voc and efficiency. The origins for this result, however, are different with that of inferior device performances at high $T_f$. In addition the phase transition of the silicon films occurs at different silane concentration (SC) by varying filament temperature, by which highest efficiency with SC vanes with $T_f$.

• Journal of Korean Critical Care Nursing
• /
• v.16 no.2
• /
• pp.1-14
• /
• 2023

Purpose : Sleep disturbances in patients in the intensive care unit (ICU) are related to health problems after discharge. Therefore, active prevention and management are required. Hence, identification of the factors that affect sleep in patients who are critically ill is necessary. Methods : The PubMed, Cochrane Library, CINAHL, EMBASE, and Web of Science databases were searched. Selection criteria were observational and experimental studies that assessed sleep as an outcome, included adult patients admitted to the ICU, and published between November 2015 and April 2022. Results : A total of 21,136 articles were identified through search engines and manual searches, and 42 articles were selected. From these, 22 influencing factors and 11 interventions were identified. Individual factors included disease severity, age, pain, delirium, comorbidities, alcohol consumption, sex, sleep disturbance before hospitalization, chronic obstructive pulmonary disease (COPD), cardiovascular disease, and high diastolic blood pressure (DBP), low hemoglobin (Hb), and low respiratory rate (RR). Environmental factors included light level, noise level, and temperature. Furthermore, treatment-related factors included use of sedatives, melatonin administration, sleep management guidelines, ventilator application, nursing treatment, and length of ICU stay. Regarding sleep interventions, massage, eye mask and earplugs, quiet time and multicomponent protocols, aromatherapy, acupressure, sounds of the sea, adaptive intervention, circulation lighting, and single occupation in a room were identified. Conclusion : Based on these results, we propose the development and application of various interventions to improve sleep quality in patients who are critically ill.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.8 s.227
• /
• pp.968-975
• /
• 2004

Nanofluids have anomalously high thermal conductivities at very low fraction, strongly temperature-dependent and size-dependent conductivities, and three-fold higher critical heat flux than that of base fluids. Traditional conductivity theories such as the Maxwell or other macroscale approaches cannot explain why nanofluids have these intriguing features. So in this paper, we devise a theoretical model that accounts for the fundamental role of dynamic nanoparticles in nanofluids. The proposed model not only captures the concentration and temperature-dependent conductivity, but also predicts strongly size-dependent conductivity. Furthermore, we physically explain the new phenomena for nanofluids. In addition, based on a proposed model, the effects of various parameters such as the ratio of thermal conductivity of nanofluids to that of a base fluid, volume fraction, nanoparticle size, and temperature on the thermal conductivities of nanofluids are investigated.

• Journal of Advanced Research in Ocean Engineering
• /
• v.4 no.1
• /
• pp.1-6
• /
• 2018

Subsea pipelines are designed to transport mixtures of oil, gas, and their associated impurities from the wellhead that can have temperatures as high as $100^{\circ}C$, while the external temperature can be as low as $5^{\circ}C$. Heat can be lost from the subsea pipeline containing high-temperature fluid to the surrounding environment. It is important that the pipeline is designed to ensure that the heat loss is small enough to maintain flow and avoid the unwanted deposition of hydrate and wax, which occurs at a critical temperature of approximately $40^{\circ}C$. Therefore, it is essential to know the heat loss of subsea pipelines under various circumstances. This paper presents a comparison between numerical analyses and existing theoretical formulas for different backfills and burial depth.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.76-78
• /
• 1994

Owing to the discover of oxide superconducting over critical temperature100K, it is being made experimentally somewhere under the possibility that there is superconducting magnet by cooling liquid nitrogen. The issues of thermal stability and quench process of Low-Tc superconductor has been studied and used application of oxide superconducting magnets. However the quench propagation property of oxide superconductor, especially experimental data about thermal behavior has not been reported yet. Therefore we measured the effect of temperature dependance of quench propagation velocity, Vq, by using the short samples made up of silver sheathed Bismuth-family (2223phase) superconducting oxide tape.

• Korean Journal Plant Pathology
• /
• v.14 no.6
• /
• pp.618-621
• /
• 1998

In pseudoperonospora humuli, the cause of hop downy mildew, environmental and host factors affecting laboratory production of oospore were examined. After 7 days incubation of leaf disk inoculated with sporangia on water, additional incubations were carried out under different conditions of temperature and moisture. Oospore production was also compared between very susceptible (Nugget) and resistant (Fuggle) hop cultivars. Oospores were not produced at 18$^{\circ}C$ regardless of other incubation conditions. Leaf disks failed to produce oospore when incubated on water for up to 18 days at 8$^{\circ}C$. No oospores formed on infection sites without necrosis. However, abundant oospores were produced at necrotized infection sites when inoculated leaf disk incubated on dry filter paper for 5 days at 8$^{\circ}C$. Both susceptible and resistant hop cultivars produced abundant oospores. In the measurement of optimal temperature for oospore production, oospores were produced at 6 to 12$^{\circ}C$ Most abundant oospores were produced at 8$^{\circ}C$. We suggest that proper combination of low temperature, dryness and necrosis may be a critical environmental factors for oospore production of P. humuli.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.12
• /
• pp.964-970
• /
• 2006

Vapor compression refrigerators have much critical variables such as the controls of temperature and pressure switches, control durations and operating hours of electronic valves. This study compares and analyzes the data which is obtained from system controlling of the evaporation temperatures which are generally used in automatic pump down operating systems. Through this study, the automatic evaporation control operation system will be more ideal for the system to keep the proper temperature distribution depending on the purpose of evaporation side. The automatic pump down control operation is more appropriate for the system to aim at the effective use of evaporation side without using the temperature difference. And this test will be proved that the changes at the low pressure side didn't have significant impacts on the high pressure side.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1388-1393
• /
• 2004

Investigators have been perplexed with the thermal phenomena behind the recently discovered nanofluids, fluids with unprecedented stability of suspended nanoparticles although huge difference in the density of nanoparticles and fluid. For example, nanofluids have anomalously high thermal conductivities at very low fraction, strongly temperature-dependent and size-dependent conductivities, and three-fold higher critical heat flux than that of base fluids. Traditional conductivity theories such as the Maxwell or other macroscale approaches cannot explain why nanofluids have these intriguing features. So in this paper, we devise a theoretical model that accounts for the fundamental role of dynamic nanoparticles in nanofluids. The proposed model not only captures the concentration and temperature-dependent conductivity, but also predicts strongly size-dependent conductivity. Furthermore, we physically explain the new phenomena for nanofluids. In addition, based on a proposed model, the effects of various parameters such as the ratio of thermal conductivity of nanofluids to that of a base fluid, volume fraction, nanoparticle size, and temperature on the thermal conductivities of nanofluids are investigated.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.4
• /
• pp.38-42
• /
• 2008

Miniature J-T cryocooler using nitrogen or argon has been widely adopted in cooling infrared sensor for space/military application and cryosurgery. Argon or nitrogen, however, has relatively low specific cooling power compared to nitrous oxide, but the ultimate operating temperature is much lower than nitrous oxide. On the other hand, nitrous oxide has large specific cooling power, but the operating temperature is limited to its boiling point (>183K). To compromise the different characteristics of these gases, the performance of miniature J-T cryocooler using argon and nitrous oxide mixture is investigated in this paper. Three different compositions of mixture (25/75, 50/50, and 75/25 molar fraction) are blended and tested. The results are compared with the experiments of pure argon and pure nitrous oxide. The experimental results show some encouraging potentiality of mixed refrigerant J-T cryocooler. The critical clogging problem, however, was observed with argon and nitrous oxide mixture, and the lowest achievable temperature with this mixture was limited to the freezing point of nitrous oxide. The paper discusses detailed clogging process of the mixture and suggests an alternative.