• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.339-345
• /
• 1998

The creep of concrete structures caused by variable stresses is mostly calculated by step-by-step method based on the superposition of creep function. Although most practical application is carried out by this linear assumption, significant deviations between predictions and experiments have been observed when unloading takes place, that is, stress is reduced. The recovery is overestimated. The main purpose of this study is to present the application method of the creep analysis model which is expressed with both creep function and creep recovery function to concrete structures where is expressed with both creep function and creep recovery function to concrete structures where increase or decrease of stress is repeated . To apply two function method to time analysis of concrete structures, this study presents the calculation method of creep strain increment for stress variation. Then, this paper executes the time analysis for an example using suggested method, and compares theses results with the previous analysis values and experimental results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.194-199
• /
• 2000

The creep rate is affected by the temperature and in fact. if the temperature above $T_M/2(T_M:melting\;point)$. The aim of the present investigation is to study the relationship of static creep and cyclic creep behavior of pure copper and the formulation of these phenomena with the special attention to the instantaneous strain. strain rate from time and number of cycles have the same inclination Steady state creep rate depend upon maximum stress and can be expressed as linear function according to Power law creep equations Creep rupture time has relation with creep rate. and it make a group represented as the same direct line regardless of max stress, stress ratio and the temperature. Initial strain effect on continuous creep deformation. and have guantitative relationship between elastic and Plastic strain. LMP have similar tendency than OSDP and MHP according to temperature

• Structural Engineering and Mechanics
• /
• 제18권5호
• /
• pp.591-607
• /
• 2004

The substance of the use of the derived non-linear creep constitutive equations under variable stress levels (see first part of the paper, Kmet 2004) is explained and the strategy of their application is outlined using the results of one-step creep tests of the steel spiral strand rope as an example. In order to investigate the creep strain increments of cables an experimental set-up was originally designed and a series of tests were carried out. Attention is turned to the individual main steps in the production and application procedure, i.e., to the one-step creep tests, definition of loading history, determination of the kernel functions, selection and definition of constitutive equation and to the comparison of the resulting values considering the product and the additive forms of the approximation of the kernel functions. To this purpose, the parametrical study is performed and the results are presented. The constitutive equations of non-linear creep of cable under variable stress history offer a strong tool for the real simulation of stochastic variable load history and prediction of realistic time-dependent response (current deflection and stress configuration) of structures with cable elements. By means of suitable stress combination and its gradual repeating various loads and times effects can be modelled.

• 열처리공학회지
• /
• 제18권3호
• /
• pp.177-182
• /
• 2005

The steady state cyclic mechanism, and the behaviour of Nicoseal(Fe-29Ni-17Co) have been examined under the condition of square wave stress cyclic tension creep test at the temperature, stress and frequency range of $430{\sim}470^{\circ}C$($0.41{\sim}0.43T_m$), 353~383 MPa, and 3 cpm, respectively. Also, the relationship between cyclic creep and static creep have been examined. The stress exponents(n) for the static creep deformation of this alloy were 11.6, 10.0, 8.4 and 7.9 at the temperature of 430, 445, 460 and $470^{\circ}C$, respectively. The apparent activation energies (Q) for the static creep deformation were 54.2, 51.8, 49.7 and 46.8 kcal/mole for the stress of 353, 363, 373 and 383 MPa, From the above results, it could be considered that the cyclic creep accelaration phenomena was obtained and that the cyclic deformation for Nicoseal seemed to be controlled by dislocation climb over the range of experimental conditions. Nicoseal alloy under the cyclic creep conditions was obtained as P=(T+460)(logt+17). The failure plane observed by SEM showed up transgranular fracture at all range.

• 대한토목학회논문집
• /
• 제34권3호
• /
• pp.755-761
• /
• 2014

콘크리트의 크리프와 건조수축 변형에 대한 내적 혹은 외적 구속은 크리프 발생 응력조건을 변화시키며 이에 따라 크리프 변형의 발생은 응력변화에 종속적으로 변화한다. 시간이력 하중을 받는 크리프 거동문제로서 이해되는 이러한 크리프 거동현상의 수학적 모델링은 일반적으로 재하시의 콘크리트 재령과 물성값 및 하중이력을 기본 구성인자로 고려하여 시간적분 혹은 점증적 형태로 유도되었다. 본 논문에서는 시간이력하중을 받는 크리프 모델 가운데 단일 크리프 곡선을 사용하는 초기 크리프 모델인 평행 크리프 법의 단순성을 고려하여 이 방법이 갖는 단점과 한계성을 극복하고 성능을 개선한 평행 크리프 법을 유도하였다. 유도된 크리프 모델의 성질을 분석하고 예측 성능을 검증하기 위한 목적으로 원통형 콘크리트 공시체를 제작하고 시간이력 하중 하의 크리프 실험을 수행하였다. 끝으로, 콘크리트 공시체의 크리프 변형으로 인한 초기하중의 변화가 공시체의 재령에 따른 거동에 미치는 영향정도를 실험을 통해 분석하였으며, 크리프 시험기의 스프링계수를 측정하여 이로 인한 실험오차를 보정하였다.

• Nuclear Engineering and Technology
• /
• 제56권1호
• /
• pp.1-8
• /
• 2024

In this study, the influence of thermal aging on structural integrity is investigated for Gr. 91 steel. A commercial grade Gr. 91 steel is used for the virgin material, and service-exposed Gr. 91 steel is sampled from a steam pipe of a super critical plant. Time versus creep strain curves are obtained through creep tests with various stress levels at 600 ℃ for the virgin and service-exposed Gr. 91 steels, respectively. Based on the creep test results, the improved Omega model is characterized for describing the total creep strain curve for both Gr. 91 steels. The proposed parameters for creep deformation model are used for predicting the steady-state creep strain rate, creep rupture curve, and stress relaxation. Creep-fatigue damage is evaluated for the intermediate heat exchanger (IHX) in a large-scale sodium test facility of STELLA-2 by using creep deformation model with proposed creep parameters and creep rupture curve for both Gr. 91 steels. Based on the comparison results of creep fatigue damage for the virgin and service-exposed Gr. 91 steels, the thermal aging effect has been shown to be significant.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.293-298
• /
• 2008

This paper attempts to quantify the effect of mismatch in creep properties on steady-state stress distributions for a welded branch vessel. A particular geometry for the branch vessel is chosen. The vessel is modeled by only two materials, the base and weld metal. Idealized power law creep laws with the same creep exponents are assumed for base and weld metals. A mismatch factor is introduced, as a function of the creep constant and exponent. Steady-state stress distributions within the weld metal, resulting from threedimensional, elastic-creep finite element (FE) analyses, are then characterized by the mismatch factor. We can find that average stresses in the weld can be characterized by the mis-match factor. And there is an analogy between elastic-creep and elastic-perfectly plastic.

• 한국지반공학회지:지반
• /
• 제9권4호
• /
• pp.93-102
• /
• 1993

연약 지반위에 축조된 토질 구조물은 제체의 자중으로 인하여 오랜 기간 동안 침하가 계속되는데 이는 시간표존적 거동인 압밀과 크리프(creep)가 동시에 작용하여 발생된다. 본 연구에서는 안산의 해성점토에 대하여 크리프거동 해석에서 필요한 정수를 구하고 수치해석시 중요시되고 있는 구속응력과 응력수준에 따른 크리프정수의 영향 특성에 대하여 연구하였다. 그 결과 탄성계수 E1과 크리프정수 n는 적용응력 수준에 영향을 받는 것으로 나타나 응력수준에 따른 크리프정수 결정식을 제시하였다.

• 한국안전학회지
• /
• 제24권6호
• /
• pp.20-26
• /
• 2009

The creep deformation behavior of AZ31 magnesium alloy was examined in the temperature range from 573 to 673K (0.62 to 0.73 Tm) under various constant stresses covering low strain rate range from $4{\times}10^{-9}\;s^{-1}$ to $2{\times}10^{-2}\;s^{-1}$. At low stress level, the stress exponent for the steady-state creep rate was ~3 and the present results were in good agreement with the prediction of Takeuchi and Argon model. At high stress level, the stress exponent was ~5 and the present results were in good agreement with the prediction of Weertman model. The transition of deformation mechanism from solute drag creep to dislocation climb creep could be explained in terms of solute-atmospherebreakaway concept.

• 대한기계학회논문집A
• /
• 제20권4호
• /
• pp.1177-1185
• /
• 1996

The crack growth under creep condition is one of the major damage mechanisms which determines remaining life of the component operating at high temperatures. In this paper, the creep crack growth by grain boundary cavitation is studied, which is frequently observed failure mechanism for creep brittle materials. As a result of diffusive growth of creep cavities, it is shown that the crack-tip stress field is modified from the original stress distribution by the amount of singularity attenuation parameter which is function of crack growth rate and material properties. Also, the stress relaxation at crack-tip results in the extension of cavitating area by the load dump effect to meet the macroscopic force equilibrium conditdion.