• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.376-381
• /
• 2009

The increasing needs for higher cargo capacity in the container vessels' fleet has led to ship builder's demand for higher power output rating engine to meet the propulsion requirement, thus, leading to the development of super large two stroke low speed diesel engines. This large sized bore engines with more than 12 cylinders are capable of delivering power output up to more than 100,000 bhp at maximum continuous rating. The thrust variation force due to axial vibration occurring in propulsion shafting of these ships are transmitted to ship structure via thrust bearing. This force may vibrate the super structure of ship in the fore-aft direction and the fatigue strength of crank shaft can be decreased by additional bending stress increase in crank shaft pin and journal. In this paper, the axial vibration of propulsion shafting system on the 14RT-flex96C super large diesel engine with 14 cylinders is identified by theoretical analysis and vibration measurement.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.653-656
• /
• 2002

This paper presents the development of 15G(Integrate Starter Generator). The ISG is the crank shaft mount type and it is installed at tile flywheel. The wide operating range of ISG requires large constant power speed ratio, good overload performance and high efficiency. High saliency ratio permanent magnet motor is developed for the ISG applications and 500A MOSFET inverter is designed to derive the ISG. The characteristic of developed ISG is investigated using the special test-bed for the 42V PowerNet and the detailed results is presented

• Journal of Biosystems Engineering
• /
• v.38 no.2
• /
• pp.73-80
• /
• 2013

Purpose: This study was conducted to compare tillage and loads characteristics of three types of rotavators in farmland working condition of Korea. Methods: Tillage operations using three types of rotavators, i.e. rotary-type, crank-type and plow-type, were carried out in a dry field of Korea. The same prime mover tractor was used for driving three types of rotavators, and under several operational conditions, tillage characteristics such as actual working speed, rotavating depth, rotavating width, actual field capacity, flow of tilled soil, soil inversion ratio, and pulverizing ratio were measured. In addition, loads characteristics like torque and required power of Power Take-Off (PTO) shaft were calculated. Results: The average rotavating depth was smaller than the nominal value for all rotavators, and the difference was the greatest in the plow-type rotavator. Nevertheless, the plow-type rotavator showed the largest rotavating depth. The rotavating width was the same as the nominal value of all rotavators. The flow of tilled soil at the same operational conditions was the greatest in the plow-type rotavator and was the smallest in the rotary-type rotavator. In the most commonly used gear conditions of L2 and L3, the average soil pulverizing ratio was the greatest in the rotary-type rotavator, and followed by crank-type and plow-type rotavators in order. In the gear L2 and L3, the plow-type rotavator also had the lowest average soil inversion ratio while the rotary-type and crank-type rotavators had the same soil inversion ratio each other. The average torque and power of PTO shaft in the gear L2 and L3 were the highest in the plow-type rotavator. The load spectra of PTO shaft applying rain flow counting method and Smith-Waston-Topper equation to the measured torque showed that the modified torque amplitude was the greatest in the crank-type rotavator. This may come from the large torque fluctuation of crank-type rotavator during tillage operations. Conclusions: The three types of rotavators had different tillage and loads characteristics. The plow-type rotavator had the deepest rotavating depth, the smallest soil inversion ratio, the largest soil pulverizing ratio and required PTO power. Also, the crank-type rotavator showed a large torque fluctuation because of their unique operational mechanism. This study will help the farmers choose a suitable type of rotavator for effective tillage operations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.6
• /
• pp.452-461
• /
• 2014

Two stroke low speed diesel engines that have many advantages such as high thermal efficiency and durability have been widely used for marine engine. However, it is also true that many problems have occurred due to the high explosion pressure and severe operating environment. Especially problems of shaft damage etc. intensively occurred due to the phenomenon of crankshaft exceeding the allowable stress, including the shaft vibration of the engine model in the early stage. In this study, the crankshaft fracture phenomenon of early engine model was evaluated and analyzed by using up-to-date torsional vibration calculation program and measurement instrument. And this was numerically shown.

• Journal of Mechanical Science and Technology
• /
• v.14 no.8
• /
• pp.891-899
• /
• 2000

The flame speed may be decomposed into the burning speed and the flame transport speed. The flame transport speed is affected considerably by the flow direction, variation rate of flow direction, and flow speed in the combustion chamber. Especially, the flow direction and the variation rate of flow direction at the spark plug location during the ignition period have an important effect on the ignition process and the early flame propagation process. We measured the flow direction component and the variation rate of flow direction with a hot wire probe at the spark plug location. It was shown that the representative flow direction of ignition period is the right-vertical direction of crank shaft and it was used to investigate the variation rate of flow direction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.90-99
• /
• 1996

To keep up with the regulation of OBD II(on board diagnostics II), many detection methods for engine misfire have been developed. Among them, the method of using the crankshaft speed fluctuation is the most noticeable in the point of view of lower cost and easier installation than any others. On the basis of the results obtained from the previous engine-dynamometer test, the integrating torque index (ITI) has been introduced. In this research, the instrumental and the interfacing systems to engine control unit(ECU) are developed for the vehicle test. Therefore, the vehicle and chassis-dynamometer test can be carried out in addition to the rough road test. From this test, the previousproposed method proved that it can be applied to the real vehicle.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.110-118
• /
• 2014

In the past two stroke low speed diesel engine were widely used for marine propulsion. these engine have many merit for example, higher thermal efficiency and durability. however, shaft vibration problem was continuously rise up due to large power of two stroke low speed diesel engine. specially, the initial stage engine revolution counter & stress has acculated. For that reason, sometimes occurred crankshaft crack accident. In this study, regarding the initial stage engine, trying to analyze what is cause the crack phenomenon using by latest torsional vibration calculation program & measurement equipment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.16 no.5
• /
• pp.17-28
• /
• 1992

During the last decade, engine makers have developed new types or increasing power rate engines to enlarge theirs marketing shear in two stroke, low-speed diesel engines. As the results, these engines have increased the additional stresses due to torsional vibration more than old model engines. The torsional vibration dampers are necessary in order to reduce heigher additional stresses of intermediate and crank shaft in these engine. In this paper, the optimum designing of Geislinger type torsional Damper has been carried out, based on the theoretical conception. The dynamic characteristics and performance fo dampers are estimated by the measuring results obtained with the monitoring system of dampers and additional stresses of propulsion shafts.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.11
• /
• pp.723-730
• /
• 2015

This paper investigated the noise generation mechanism of a rotary compressor using experimental method. The measurement was carried out for primary parameters which influence noise characteristics. By using STFT(short time Fourier transform), noise sources of a rotary compressor were identified and vibrating modes that increase the noise are verified. Also, it was studied that the correlation between operating speed and noise. Main factors that affect the variation of noise level were considered by the comparison of the experimental results. In addition, a dynamic characteristic of crank shaft was studied and the critical speed was analyzed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.753-759
• /
• 2014

In this paper, it is investigated that noise generation mechanism of a rotary compressor using experimental method. The measurement was carried out for primary parameters which influence noise characteristics. By using STFT(short time fourier transform), noise sources of a rotary compressor were identified and vibrating modes that increase the noise are verified. Also, it was studied that the correlation between operating speed and noise. Main factors that affect the variation of noise level were considered by the comparison of the experimental results. In addition, a dynamic characteristic of crank shaft was studied and the critical speed was analyzed.