• Structural Engineering and Mechanics
• /
• 제49권2호
• /
• pp.225-235
• /
• 2014

Cold expansion is an efficient way to improve the fatigue life of an open hole. In this paper, three finite element models have been established to bind the crack growth from an expanded hole and simulated. Expansion and its degree influence are studied using a numerical analysis. Stress intensity factors are determined and used to evaluate the fatigue life. Residual stress field is evaluated using a nonlinear analysis and superposed with the applied stresses field in order to estimate fatigue crack growth. Experimental tests are conducted under constant loading. Results of this investigation indicate expansion and its degree are beneficial to fatigue life and a good agreement was observed between FEM simulations and experimental results.

• 대한기계학회논문집A
• /
• 제24권12호
• /
• pp.3088-3095
• /
• 2000

Creep-fatigue crack growth behavior was experimentally measured particularly when a crack was located in the heat affected region of lCr-5Mo steel. Load hold times of the tests for trapezoidal fatigue waveshapes were varied among 0, 30, 300 and 3,600 seconds. Time-dependent crack growth rates were characterized by the $C_r$parameter. It was found that the crack growth rates were the highest when the crack path was located along the fine-grained heat affected zone(FGHAZ). Cracks located in other heat affected regions had a tendency to change the crack path eventually to FGHAZ. Creep-fatigue crack growth law of the studied case is suggested in terms of (da/dt)$_{avg}$ vs. ($C_t$)$_{avg}$ for residual life assessment.

• 한국항공우주학회지
• /
• 제40권4호
• /
• pp.336-345
• /
• 2012

균열성장 수명에는 구조 형상의 복잡함, 작용하중의 변동, 재료물성 분포 등의 영향으로 불확실성이 포함된다. 따라서 이러한 불확실 인자들에 대해 계산된 수명의 강건성을 확보하기 위해서는 신뢰성 평가가 요구된다. 하지만 형상이 복잡한 터빈 휠의 경우 균열성장 수명 계산의 주요 변수인 응력확대계수의 표현식을 알기 힘들며, 이를 유한요소해석으로 계산하므로 수명 계산 및 신뢰성 평가에 많은 시간이 요구된다. 따라서 본 연구에서는 균열성장 수명의 반응표면을 사용함으로써 신뢰성 평가의 효율성을 높일 수 있음을 고찰하였다. 이를 위해 형상이 복잡한 터빈 휠을 모델로 유한요소해석으로 생성된 응력확대계수 데이터를 회귀분석하여 근사모델을 생성한 후 응력확대계수의 회귀계수, Paris 계수, 초기균열길이에 대한 균열성장 수명의 반응표면을 생성하여 신뢰성해석에 사용하였다. 신뢰성해석은 몬테카를로 시뮬레이션으로 수행하였으며, 연구결과 반응표면의 사용이 신뢰성 평가 시 필요한 균열성장 수명의 계산량을 효과적으로 줄일 수 있었다.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1097-1103
• /
• 1988

본 연구에서는 이 좁은 벤트내에 자료가 모이는 피로균열의 특성을 이용하여 표면피로균열의 성장거동을 파괴역학적으로 해석, 연구하여 균열의 성장특성과 $S-N_{f}$ 곡선의 추정을 마이크로 컴퓨터로 계산하였다.

• 항공우주시스템공학회지
• /
• 제1권1호
• /
• pp.45-52
• /
• 2007

This paper analyzed the extension effects of fatigue life and the application of pre-indentation in aircraft structural material such as aluminum alloys. The test specimen used the thin sheet of aluminum alloy with a single-edged notch. The experiments were conducted after making the pre-crack under a constant amplitude loading. As the fatigue life extension technique, the pre-indentation making an indent on the predicted path of crack propagation was applied. The work presented here discussed about a proper mathematical relation between crack growth rate and the range of stress intensity factor and about the generalization of crack growth mechanism with large retardation effect. A technique to enhance the applicability of pre-indentation if also mentioned.

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.365-373
• /
• 2002

For gas turbine engines, the safe life methodology has historically been used fur fatigue life management of failure critical engine components. The safe retirement limit is necessarily determined by a conservative life evaluation procedure, thereby many components which have a long residual life are discarded. The objective of this study is to introduce the damage tolerant design concept into the life management for aircraft engine component instead of conservative fatigue life methodology which has been used for both design and maintenance. Crack growth data were collected on a nickel base superalloy which have been subjected to combined static and cyclic loading at elevated temperatures. Stress analysis fur turbine disk was carried out. The program for computing creep-fatigue crack growth was developed. The residual lifes of turbine disk component under various temperatures and conditions using creep-fatigue crack growth data were estimated. As the result of analysis, it was confirmed that retirement fur cause concept was applicable to the evaluation of residual life of retired turbine disk which had been designed based on the conventional fatigue life methodology.

• Composites Research
• /
• 제16권3호
• /
• pp.9-17
• /
• 2003

타이어 벨트층내의 코드간 균열연결 및 층간균열진전을 모사하기 위해 자유단을 갖는 2층 고무/코드 적층시험편에 대한 4~11mm 변위제어 실험을 수행하였다. 자유단의 코드간 균열연결시의 폭방향 균열진전량은 45$^{\circ}$ 경사진 코드들간 길이의 절반에 도달할 때의 측정값으로 하였으며, 이는 탐침법에 의해 측정되었다 또한, 자유단에서 코드들간 균열연결을 모사하기위해 2차원의 이상화된 모델링 기법을 고안하였다. 이론수명은 테어링에너지(균열파단면의 단위면적당 방출에너지)를 이용하여 코드간 균열연결수명(임계값)과 이후 최종파손까지의 수명으로 구분하였으며, 이들을 각기 실험값과 비교하였다. 임계값까지의 수명예측은 실험과 비교하여 약 20%, 최종파손까지 약 65%의 오차가 발생하였다. 따라서, 전체 이론수명은 실험과 비교하여 약 45%의 오차를 발생하였다.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1722-1729
• /
• 1994

At early stage of creep-fatigue crack growth tests, initial transient behavior which implies high crack growth rate has been generally observed by some researchers. Since the influence of the initial transient crack growth behavior on the remaining life of components is significant, cause of it should be further studied. In this study, characteristics of the initial transient behavior of 1Cr-1Mo-0.25V steel is studied experimentally by performing creep-fatigue crack growth tests at $538^{\circ}C$ in air under trapezoidal waveshapes. It is verified that the cause of the initial transient behavior is not high ${(C_t)}_{avg}$ values due to the small scale creep condition at the early stage of test, but oxidation-dominated crack growth mechanism during the transient period which is different from the creep-dominated crack growth mechanism in steady crack growth period.

• 한국해양공학회지
• /
• 제13권3호통권33호
• /
• pp.36-48
• /
• 1999

Fatigue life and crack retardation behavior after penetration were experimentally examined using surface pre-cracked specimens of aluminium alloy 5083. The Wheeler model retardation parameter was used successfully to predict crack growth behavior after penetration. By using a crack propagation rule, the change in crack shape after penetration can be evaluated quantitatively. Advanced, waveform-based acoustic emission (AE) techniques have been successfully used to evaluate signal characteristics obtained form fatigue crack propagation and penetratin behavior in 6061 aluminum plate with surface crack under fatigue stress. Surface defects in the structural members are apt to be origins of fatigue crack growth, which may cause serious failure of the whole structure. The nondestructive analysis on the crack growth and penetration from these defects may, therefore, be one of the most important subjects on the reliability of the leak before break (LBB) design. The goal of the present study is to determine if different sources of the AE could be identified by characteristics of the waveforms produced from the crack growth and penetration. AE signals detected in four stages were found to have different signal per stage. With analysis of waveform and power spectrum in 6061 aluminum alloys with a surface crack, it is found to be capabilities on real-time monitoring for the crack propagation and penetration behavior of various damages and defects in structural members.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.475-485
• /
• 1995

In this study, statistical analysis of fatigue data which had obtained from respective 24 fatigue crack, was examined for SiC whisker reinforced aluminium 6061 composite alloy (SiC$_{w}$/A16061) and aluminium 6061 alloy. SiC volume fraction in composite alloy is 25%. The analysis results stress intensity factor range and 0.1 mm fatigue crack initiation life for SiC$_{w}$/A16061 composite & A16061 matrix are the log-normal distribution. And regression analysis by linear model, exponential model and multiplicative model were performed to find out the relationship between fatigue crack growth rate(da/dN) and stress intensity for find out the relationship between fatigue crack growth rate(da/dN) and stress intensity factor range(.DELTA.K) in the SiC$_{w}$/A16061 composite and examine the applicability of Paris' equation to SiC$_{w}$A16061 composite. Also computer simulation was performed for fatigue life prediction of SiC$_{w}$/A16061 composite using the statistical results of this study.udy.