• Computers and Concrete
• /
• 제24권6호
• /
• pp.527-539
• /
• 2019

In this paper, the fracture characteristics of concrete specimens with different notch depths under three-point flexural loads are studied by finite element and fracture mechanics methods. Firstly, the concrete beams (the size is 700×100×150 mm) with different notch depths (a=30 mm, 45 mm, 60 mm and 75 mm respectively) are tested to study the influence of notch depths on the mechanical properties of concrete. Subsequently, the concrete beams with notch depth of 60 mm are loaded at different loading rates to study the influence of loading rates on the fracture characteristics, and digital image correlation (DIC) is used to monitor the strain nephogram at different loading rates. The test results show that the flexural characteristics of the beams are influenced by notch depths, and the bearing capacity and ductility of the concrete decrease with the increase of notch depths. Moreover, the peak load of concrete beam gradually increases with the increase of loading rate. Then, the fracture energy of the beams is accurately calculated by tail-modeling method and the bilinear softening constitutive model of fracture behavior is determined by using the modified fracture energy. Finally, the bilinear softening constitutive function is embedded into the finite element (FE) model for numerical simulation. Through the comparison of the test results and finite element analysis, the bilinear softening model determined by the tail-modeling method can be used to predict the fracture behavior of concrete beams under different notch depths and loading rates.

• 한국지진공학회논문집
• /
• 제24권5호
• /
• pp.233-241
• /
• 2020

This paper is to investigate the retrofitting effect for a non-seismic reinforced concrete frame strengthened by perimeter steel moment frames with indirect integrity, which ameliorates the problems of the direct integrity method. To achieve this, first, full-scale tests were conducted to address the structural behavior of a two-story non-seismic reinforced concrete frame and a strengthened frame. The non-seismic frame showed a maximum strength of 185 kN because the flexural-shear failure at the bottom end of columns on the first floor was governed, and shear cracks were concentrated at the beam-column joints on the second floor. The strengthened frame possessed a maximum strength of 338 kN, which is more than 1.8 times that of the non-seismic specimen. A considerable decrease in the quantity of cracks for the strengthened frame was observed compared with the non-seismic frame, while there was the obvious appearance of the failure pattern due to the shear crack. The lateral-resisting capacity for the non-seismic bare frame and the strengthened frame may be determined per the specified shear strength of the reinforced columns in accordance with the distance to a critical section. The effective depth of the column may be referred to as the longitudinal length from the border between the column and the foundation. The lateral-resisting capacity for the non-seismic bare frame and the strengthened frame may be reasonably determined per the specified shear strength of the reinforced columns in accordance with the distance to a critical section. The effective depth of the column may be referred to as the longitudinal length from the border between the column and the foundation. The proposed method had an error of about 2.2% for the non-seismic details and about 4.4% for the strengthened frame based on the closed results versus the experimental results.

• 콘크리트학회지
• /
• 제7권5호
• /
• pp.179-188
• /
• 1995

강섬유보강콘크리트는 콘크리트의 취성을 극복하고 콘크리트 내의 강섬유의 구속작용과 균열제어메카니즘, pull-out저항 등에 의하여 강도가 증진되며 이러한 작용에 의하여 전단하중하에서도 강도와 연성의 증대를 가져온다. 강섬유보강콘크리트의 2차적인 보강효과는 휨보다는 전단거동에 대하여 더 효율적인 것으로 보고되고 있다. 따라서 시멘트계 재료에 훅트강섬유를 혼입함으로써 전단하중 하에서 훅트강섬유보강 철근콘크리트보(RHSFCB)의 전단저항력이 증가되고 결과적으로 보의 구조적 거동과 전단강도가 향상된다. 본 연구에서는 RHSFCB의 전단거동에 영향을 미치는 주요 변수들에 대한 각 영향을 실험적으로 고찰하였으며, 본 연구에서 고찰한 주요변수는 섬유혼입율, 전단-스팬비, 스터럽의 간격등이다. 이론적 고찰은 문헌에 보고된 각 전단강도 예측식들에 본 실험에서 전단파괴한 9개 시험체와 문헌에 나타난 86개의 전단파괴시험체를 적용하여 각 예측식들의 전단강도를 비교하였으며, 그 결과치를 통계분석하여전단강도예측식의 정확성을 고찰하였다.

• 토지주택연구
• /
• 제2권4호
• /
• pp.553-558
• /
• 2011

말뚝두부와 기초판의 연결방법으로서 기존의 강선남김방식은 시공성이 좋지 않고, 말뚝두부에 파손 및 균열이 발생할 가능성이 높을 뿐만 아니라 현장 인명사고가 자주 발생하여 최근에는 대안적인 방법으로서 원커팅에 의한 철근보강 방식이 제안되어 사용되고 있다. 하지만 이러한 방법들은 역학적인 성능규명에 의하여 그 상세가 구체적으로 제안 또는 검증된 사례가 없다. 이 연구는 원커팅 철근보강 방식에 있어서 최적 보강상세를 제안 할 목적으로 후 타설된 말뚝 내 속채움 콘크리트와 말뚝간의 전단마찰 저항력의 부족으로 인한 파괴를 실험을 통하여 규명하고, 적정 채움 깊이를 제안하였다. 실험결과에 근거하여 말뚝 부착파괴 강도를 안전측의 값으로 0.4MPa를 가정한다면, 부착파괴 이전에 철근이 항복에 도달하도록 하기 위해서 속채움 콘크리트의 깊이는 최소한 PHC 450과 PHC 500의 경우 600mm 이상, PHC 600의 경우 1,000mm 이상 확보하여야 할 것으로 판단된다.

• 한국주거학회논문집
• /
• 제26권2호
• /
• pp.103-110
• /
• 2015

Precast Concrete (PC) construction method can be the one that is suitable for long-life housing due to its merit in respect of maintenance and durability based on crack-free from mass production with indirect construction cost-saving-effect due to shortening construction period comparing to the conventional construction method, but it has the problem that causes the raise of direction construction costs. So, this study analyzed its economic feasibility of PC method whose maintenance and durability are excellent for underground parking lot of apartment house for accomplishing cost-saving long-life housing by applying the various structural system. In evaluation of unit module structural system, two-way PC system requires 10 to 28% more costs for frame work than RC rigid frames, and, one-way PC system 98~112%. Although it varies depending on the method, the costs are similar to RC rigid frame structure, provided a proper method is adopted. Also, Model 11, which was most economical in the evaluation, was applied to an real parking lot and about 2 to 6% of construction costs was reduced than RC rigid frames. This seems to be because, although PC system has a higher production cost, introduction of P.S (prestress) reduces member depth and, therefore, height, as well as the number of members per unit module.

• Journal of Welding and Joining
• /
• 제26권1호
• /
• pp.69-75
• /
• 2008

Spot welding which use the main process for side block production of stainless steel railway vehicle is legged behind in laser welding about a quality and productivity. Although the laser welding has many potential advantages such as low heat input and aspect ratio of weld bead, its application to a new structural component still is required many engineering data including mechanical properties such as tensile, fatigue strength, etc on. Therefore, experimental analysis was carried out to understand the fatigue phenomena of different thickness stainless steel overlap joining panels by Nd:YAG laser welding. The fatigue life curves were obtained through fatigue tests with the various levels of applied load. The fatigue life is related with the parameters such as gap size and penetration depth through experiment. As the results, tensile strength and fatigue life were proportional in heat input level and gap was identified the major factor for fatigue life. Also we could know that deferent a-ferrite content at HAZ depend on welding heat input was important factor to determine a formation of initial crack and total fatigue life cycle.

• Earthquakes and Structures
• /
• 제4권4호
• /
• pp.429-449
• /
• 2013

Current Design Codes for Reinforced Concrete (RC) interior beam-column joints are based on limited experimental studies on the seismic behavior of eccentric joints. To supplement existing information, an experimental study was conducted that focused on the effect of eccentricity of the deeper beams with respect to the shallow beams. A total of eight one-third scale interior joints with beams of different depths were subjected to reverse cyclic loading. The primary variables in the test specimens were the amount of joint transverse reinforcement and the cross section of the shallow beams. The overall performance of each test assembly was found to be unsatisfactory in terms of joint shear strength, stiffness, energy dissipation and shear deformation. The results indicated that the vertical eccentricity of spandrel beams in this type of joint led to lower capacity in joint shear strength and severe damage of concrete in the joint core. Increasing the joint shear reinforcement was not effective to alter the failure mode from joint shear failure to beam yielding which is favorable for earthquake resistance design, whereas it was effective to reduce the crack width at the small loading stages. Based on the observed behavior, the shear stress of the joint core was suggested to be kept as low as possible for a safe and practical design of this type of joint.

• 한국전자통신학회논문지
• /
• 제15권1호
• /
• pp.101-106
• /
• 2020

본 연구는 다양한 어셈블리 부품의 용접부 내부결함을 검사하기 위한 초음파 탐상 장비 개발에 관한 것이다. 본 연구에서는 초음파 탐상을 위하여 시스템의 모션제어 S/W, 초음파 송수신기 제어, 결함 판정 기준 설정 등의 계측 S/W 등이 설계되었으며, 양품과 불량품의 비교분석을 하기 위하여 용접결함 불량품 샘플워크 등도 제작되었다. 이와 같은 구성으로 이루어진 시스템을 통하여 어셈블리 부품 용접부의 결함 위치 및 깊이에 대한 자동검사 기능을 수행할 수 있었으며, 종전에 전문가에 의해 이루어졌던 용접부의 내부결함에 대한 판단을 시스템이 수행하도록 하였다.

• 콘크리트학회논문집
• /
• 제18권2호
• /
• pp.233-238
• /
• 2006

본 연구에서는 염해환경에 노출되어 있는 철근콘크리트 구조물의 수명예측에 있어서 철근덮개 파괴시간 예측을 위하여, 유한요소해석을 통한 방법을 제시하였다. 또한 본 연구에서는 인공세공용액중의 철근 부식속도로부터 콘크리트 중의 철근 부식속도를 유도하는 방법을 제시하였으며, 철근 부식의 분포에 따른 철근덮개의 파괴시간을 비교하여, 철근덮개 파괴시간을 합리적으로 예측하기 위한 방법을 제시하였다. 국부부식을 고려한 경우 균일한 부식을 가정한 경우보다 최대 약 40%정도 철근덮개 파괴시간이 짧아짐을 알 수 있다. 따라서, 철근덮개의 파괴시간 예측을 위한 유한요소해석에 있어서 국부부식을 고려하는 것이 합리적인 결과를 제시할 수 있을 것으로 사료된다.

• Journal of Welding and Joining
• /
• 제14권5호
• /
• pp.49-58
• /
• 1996

In Korea Gas Corporation, as one of the pipeline repairing methods, damaged pipelines are sometimes treated with a temporally employment of split sleeve. On conducting the repair process, circumferential fillet and longitudinal groove welding usually must be included. For the case of groove welding, a considerable amount of R&D have been carried out related to property changes, while few study on the property change in fillet welding has been conducted. In this paper, so as to confirm the specification of fillet welding in terms of safety and reliability, properties changed by fillet welding were investigated for two welding processes. Qualifying tests such as reviewing macrostructure and nick-break tests were performed according to API 1104 and ASME section IX. In addition, tensile properties and hardness were evaluated according to KS B0841 and BS 4515. The fillet weld prepared by the qualified procedure showed melting depth of 0.8∼1.3mm and heat affected zone of 2.8∼3.4mm length. No crack and lack of penetration were observed. And the results of hardness and nick-break tests satisfied code requirements. The area crossed by fillet and groove welding line was found to have minimal tensile strength.