• 열처리공학회지
• /
• 제23권3호
• /
• pp.156-162
• /
• 2010

The modified 9Cr-1Mo steel (P91 steel) is very popular as a boiler tube material of the USC (Ultra-Supercritical) power plants. The steels were tempered in the temperature range of 400 to $650^{\circ}C$ and the mechanical tests, such as impact and hardness tersts were performed at the room temperature for the tempered steels. A drop in the impact value (embrittlement) and the hardeness increase were simultanously observed in the range of temperature between $475^{\circ}C$ and $600^{\circ}C$, particularly at $550^{\circ}C$. TEM observation shows the hardening was caused by $M_2C$, resulting in the embrittlement. And the maximum volume fraction of $M_3C$ was also observed at $550^{\circ}C$, Therefore, the embrittlement seems to be caused by both the $M_2C$ and $M_3C$.

• 한국분말재료학회지
• /
• 제28권5호
• /
• pp.375-380
• /
• 2021

In this study, we investigate the effect of the duration of mechanical alloying on the microstructures and mechanical properties of ODS ferritic/martensitic steel. The Fe(bal.)-10Cr-1Mo pre-alloyed powder and Y₂O₃ powder are mechanically alloyed for the different mechanical alloying duration (0 to 40 h) and then constantly fabricated using a uniaxial hot pressing process. Upon increasing the mechanical alloying time, the average powder diameter and crystallite size increased dramatically. In the initial stages within 5 h of mechanical alloying, inhomogeneous grain morphology is observed along with coarsened carbide and oxide distributions; thus, precipitate phases are temporarily observed between the two powders because of insufficient collision energy to get fragmented. After 40 h of the MA process, however, fine martensitic grains and uniformly distributed oxide particles are observed. This led to a favorable tensile strength and elongation at room temperature and 650℃.

• 대한금속재료학회지
• /
• 제47권5호
• /
• pp.283-289
• /
• 2009

This paper dealt with a statistical analysis for evaluating the creep crack growth rate (CCGR) for Modified 9Cr-1Mo (ASTM Grade 91) steel. The CCGR data was obtained by the creep crack growth (CCG) tests conducted under various applied loads at $600^{\circ}C$. To obtain logically the B and q values used in the CCGR equation, three methods such as the least square fitting method (LSFM), the mean value method (MVM) and the probabilistic distribution method (PDM) were adopted and their CCGR lines were compared, respectively. In addition, a number of random variables were generated by using the Monte Carlo simulation (MCS), and the CCGR lines were predicted probabilistically. It was found that both the B and q coefficients followed a 2-parameter Weibull distribution well. In the case of the ranges of 10-90% for the probability variables, P(B, q), the CCGR lines were predicted. Fractographic study was conducted from the specimen after the CCG tests.

• 한국정밀공학회지
• /
• 제14권11호
• /
• pp.69-76
• /
• 1997

The rotating bending fatigue tests were performed using the specimens taken from Cr-Mo-V steel, widely sued in thermal power plant turbines, at various temperatures such as room temperature, 300 .deg. C, 425 .deg. C and 550 .deg. C. The characteristics of fatigue crack propagation were examined and analyzed by using fracture mechanics parameter. The plastic replica method was also applied in order to measure the crack length on the basis of serial observation of fatigue crack propagation behavior on the defected specimen surface. The fatigue crack propagation behavior of Cr-Mo-V steel was investigated within the frame work of elastic-plastic fracture mechanics. The propagation law of fatigue crack is obtained uniquely by using the term .sigma. $^{n}$ sub a/where .sigma. $_{a}$ is the service stress, a is the crack length and n is a constant. The values of constant n are nearly equal to 2.48, 2.60 and 8.61 at room temperature, 300 .deg. C and 425 .deg. C.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제4권2호
• /
• pp.101-109
• /
• 2016

발전소 내열강의 물성치는 고온 가동시간이 누적됨에 따라 열시효의 영향을 받는다. 본 연구에서는 제 4 세대 원자력시스템의 재료로 널리 채택되고 있는 Mod.9Cr-1Mo (ASME Grade 91)강을 대상으로 항복강도, 인장강도 및 파괴거동에 열시효가 미치는 영향에 대해 조사 및 분석하였다. 국내에서 가동 중인 초초임계(USC) 화력발전소의 배관계통에서 채취한, 73,716 시간의 가동 이력을 겪은 Gr.91 강 재료가 재료 실험을 위해 사용되었고, 동 시험결과와 가동 이력을 겪지 않은 신재의 시험결과를 비교 분석하였다. 또한 ASME 코드의 물성치와 RCC-MRx 의 물성치와 비교 분석하였고, 이들 설계기술기준 물성치의 보수성은 신재 및 가동 이력을 겪은 재료의 시험결과와 비교 분석을 통해 정량화하였다.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.148-154
• /
• 2018

When shooting small arms, the inner surface temperature is heated up to about $700{\sim}1,000^{\circ}C$ by the friction of the bullet and the inner wall of the barrel and the combustion of propellant. High-temperature propellant gas and high-speed movement of the bullet cause corrosion of the inner wall, which is noticeable immediately in front of the chamber. In this study, the mechanical properties of Cr-Mo-V steel, which is the base material, were tested using Taguchi experimental design to find the best nitriding treatment conditions. For the nitriding process, the working time, salt bath temperature, and salt concentration were combined as three conditions and placed in the $L_9(3^4)$, orthogonal array table. The thicknesses of the white layer and the nitrogen diffusion layer were measured after nitriding under each condition in a salt bath furnace. Durability was evaluated by measuring the degree of dispersion through actual shooting because it was difficult to evaluate the mechanical properties of the cylinder inner structure. As a result, it was confirmed that the durability was optimal at $565^{\circ}C$, 1 hour, 0.5%. These optimal conditions were selected by the statistical analysis of the Minitab program(ver.17).

• 비파괴검사학회지
• /
• 제27권5호
• /
• pp.417-425
• /
• 2007

보자력 측정을 통하여 페라이트기 9Cr-1Mo-V-Nb 내열강의 크리프-피로변형 동안 미세조직의 변화를 평가하였다. 크리프-피로시험은 $550\;^{\circ}C$에서 각각 인장유지시간을 60초와 600초로 하여 수행 하였다. 보자력은 파단 전까지 감소하였고 경도는 파단 시까지 지속적으로 감소하였다. 크리프-피로 수명소비율이 증가함에 따라서 $M_{23}C_6$ 탄화물은 오스트왈드 성장기구를 따라서 조대화가 나타났지만 MX 탄질화물은 $550\;^{\circ}C$에서 안정하기 때문에 조대화가 나타나지 않았다. 마르텐사이트 래스 폭은 래스경계에서의 전위회복으로 인해 증가하였다. 보자력은 전위, 석출물 그리고 마르텐사이트 래스경계와 같은 미세조직적 특성에 영향을 받게 되며 이를 미세조직변화와 관련하여 이해하였다. 결과적으로, 본 연구는 페라이트기 9Cr-1Mo-V-Nb 내열강의 크리프-피로변형 동안 미세조직의 변화와 손상 정도를 보자력을 통하여 평가하는 것을 제안하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.678-683
• /
• 2003

Ultrasonic method using SH(shear horizontal) wave has been developed to determine the surface damage in fatigued material. Fatigue damages based on propagation energy were analyzed by multiregression analysis and phase measurement in interrupted fatigue test specimen including CrMoV and 12Cr alloy steel. From the test results, as the fatigue damage increased the propagation time of the launched waves increased and amplitude of wavelet decreased. Also, analysis for the waveform modulation showed a reliable estimation, with confidence limit of 97% for 12Cr steel and 95% for CrMoV steel, respectively. Therefore, It is thought that SH ultrasonic wave technique can be applied to determine fatigue damage of in-service component nondestructively.

• 대한치과기공학회지
• /
• 제36권3호
• /
• pp.149-158
• /
• 2014

Purpose: Dental casting Co-Cr-Mo based alloys of five kinds of ingot type and two kinds of shot type were analyzed the melting processes with heating time of high frequency induction centrifugal casting machine using infrared thermal image analyzer. Methods: When Co-Cr-Mo based alloys were put about 30g/charge in the ceramic crucible of high frequency induction centrifugal casting machine and heat, Infrared thermal image analyzer and IR thermometer indicated these alloys in the crucible were set and operated. Results: The melting temperatures of alloys measuring infrared thermal image analyzer were deviated ${\pm}10^{\circ}C$ compared to those of manufacturing company. On the other hand, the melting time of alloys were differently appeared with the shape of alloys(ingot and shot type). Conclusion: The melting temperatures of dental Co-Cr-Mo based alloys were measured the degree of $1,360{\sim}1410^{\circ}C$ and the heating time with the alloys of ingot and shot type were deviated ${\pm}10sec$.

• 대한기계학회논문집A
• /
• 제35권3호
• /
• pp.251-257
• /
• 2011

본 연구는 차세대 원자로의 후보 재료인 수정 9Cr-1Mo 강에 대한 크리프 균열 성장률 법칙, da/dt=B$(C^*)^q$의 파라메터 B와 q에 대한 통계적 성질에 대하여 취급하였다. 본 해석에 이용된 크리프 균열 성장 데이터는 $600^{\circ}C$의 일정 온도에서 5000N의 동일 하중하의 1/2 CT 시험편에 대하여 크리프 균열 성장 실험을 수행하였다. 크리프 균열 성장 거동은 크리프 균열 성장률 da/dt 와 파괴역학 파라메터 $C^*$와의 실험적 관계식으로부터 통계적으로 해석하였다. 각각의 시험편에 대한 파라메터 B와 q는 최소자승법에 의하여 결정하였다. B와 q에 대한 확률분포함수를 정규분포, 대수정규분포 그리고 와이블분포에 대하여 조사하였다. 본 연구에 의하면, B와 q의 확률분포함수는 대수정규분포와 와이블분포에 비교적 잘 따름을 알았다. 또한 이들 사이에는 강한 양의 선형적인 상관이 있음을 알았다.