• Textile Coloration and Finishing
• /
• v.26 no.3
• /
• pp.218-229
• /
• 2014

The wearing comfort of garment is governed by two kinds of characteristics such as moisture and thermal transport properties and mechanical properties of fabrics. The porosity influenced by yarn and fabric structural parameters is known as main factor for wearing comfort of garment related to the moisture and thermal transport properties. This study investigated effect of porosity of composite yarns to the moisture and thermal comfort properties of composite fabrics made of hollow composite DTY and ATY yarns. The theoretical porosity and pore size were inversely proportional to cover factor of fabric, but cover factor was not correlated with experimental pore size. The wicking property of hydrophobic PET filament fabric showed inferior result irrespective of porosity, pore size and cover factor. The drying rate was superior at composite fabrics with high pore size and low cover factor, and pore size was dominant factor for drying property. On the other hand, thermal conductivity of composite fabric was mainly influenced by cover factor and not influenced by porosity. Air permeability was influenced by both porosity and cover factor and was highly increased with increasing porosity and decreasing fabric cover factor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.227-231
• /
• 2004

Technological advance in information technology has sparked the necessity of small form factor (SFF) optical disk for mobile devices. Small form factor optical disk is highly anticipated to be a next generation storage device because it can be used for a cost-effective way compared with solid state memory. For the application to the 5 mm height small-form-factor optical disk drive, we have presented an optical flying head and swing arm actuator. In this study, we propose a small 1-axis actuator for compensating ficus error and SA due to the variation of cover-layer thickness in the cover-layered small optical disk. The main design issues of the 1-axis actuator are the realization of compact structure and the new support structure of the actuator: Finally, the compensating principle and performance of the 1-axis actuator will be explained.

• Computers and Concrete
• /
• v.3 no.2_3
• /
• pp.145-161
• /
• 2006

This article involves architecting prototype-fuzzy expert system for designing the nominal cover thickness by means of fuzzy inference for quantitatively representing the environment affecting factor to reinforced concrete in chloride-induced corrosion environment. In this work, nominal cover thickness to reinforcement in concrete was determined by the sum of minimum cover thickness and tolerance to that defined from skill level, constructability and the significance of member. Several variables defining the quality of concrete and environment affecting factor (EAF) including relative humidity, temperature, cyclic wet and dry, and the distance from coast were treated as fuzzy variables. To qualify EAF the environment conditions of cycle degree of wet-dry, relative humidity, distance from coast and temperature were used as input variables. To determine the nominal cover thickness a qualified EAF, concrete grade, and watercement ratio were used. The membership functions of each fuzzy variable were generated from the engineering knowledge and intuition based on some references as well as some international codes of practice.

• Journal of Environmental Science International
• /
• v.17 no.5
• /
• pp.485-491
• /
• 2008

The present study examined the relation between land cover condition and temperature in various types of urban green spaces. The diagram of temperature distribution showed that high-temperature zones are formed around paved areas, and low temperature zone around planted areas and grassy areas. Even in planted areas where low-temperature zones were formed, temperature was different according to hierarchical structure. That is, temperature was relatively low in areas covered with arbor + sub-arbor. With regard to land cover ratio, the increase of planted areas and grassy areas had an effect on the fall of temperature and the effect was higher in order of planted areas and grassy areas. On the contrary, paved areas and bare areas had an effect on the rise of temperature. According to the results of factor analysis, in case of the highest temperature, planted area and grassy area were put together into a factor lowering temperature, paved area and temperature into a factor raising temperature, and bare area alone into a factor of low significance. In case of the lowest temperature, grassy area and bare area were put together into a factor, and the validity of the factor analysis was proved by the analysis of urban heat islands. An increase in the number of trees by height was effective in lowering temperature, and the effect was high in order to arbor and sub-arbor, and the source of coldness in planted area was tall trees.

• Journal of Korea Water Resources Association
• /
• v.38 no.1
• /
• pp.59-71
• /
• 2005

Mountain watersheds are a lot of problems about soil erosion because of frequent wildfire occurrence. Runoff and soil erosion caused by the rain on a hillslope after wildfire are dependent on cover factor. And these has been a decrease by the cover factor recovery following time passage. The present paper defines the dynamic sensitivity of runoff and soil erosion that is the rate of runoff volume and soil erosion weight to rainfall energy and analyzes characteristics of the sensitivity for variation of cover factor, In according to the correlation analysis between other parameters and sensitivities, the sensitivity is the most dependent on the cover factor and the relation is exponential. The sensitivities after wildfire have suitable relation with treatment method for the mitigation of burnt forest and wildfire intensity. It was confirmed that the variation of soil erosion sensitivities come upon the range of stability in 5 years after wildfire.

• Journal of Korean Society of Forest Science
• /
• v.107 no.1
• /
• pp.50-58
• /
• 2018

The purpose of this study was to investigate the effects of Aruncus dioicus on annual soil erosion reduction effect. Based on the measured soil erosion data, the cover factor of RUSLE was calculated. Comparing calculated the cover factor and Chewings fescue cover factor for soil erosion reduction, It found that cover crop Aruncus dioicus of reducing soil erosion was effective. The amount of soil erosion according to the type of Aruncus dioicus covering was 2.22 Mg/ha, Chewings fescue was 1.85 Mg/ha, 10.60 Mg/ha was produced in the Bare ground. Cover factor of Aruncus dioicus was $0.09{\pm}0.03$ according to the type of covering, Chewings fescue was $0.08{\pm}0.03$, Bare ground was $0.35{\pm}0.10$. Weeds control Bare ground was $0.83{\pm}0.14$. The results of the variance analysis of the cover factor for each covering were different according to the cover type. As a result of the classification of the same group through post - analysis, it was found that the Aruncus dioicus and Chewings fescue were similar to each other. Therefore, the Aruncus dioicus was effective to reduce the soil erosion to the extent that it was comparable to the Chewings fescue.

• Transactions of Materials Processing
• /
• v.15 no.1 s.82
• /
• pp.76-81
• /
• 2006

In this study, warpage characteristics of mobile phone cover through injection molding process were investigated using design of experiments in injection molding process. Warpage in plastic injection molding has a significant effect on quality of product. Effects of injection time, packing pressure, packing time, mold temperature and melt temperature on the warpage of mobile phone cover were considered by numerical analysis and experiment with Taguchi method. The degree of warpage for the injection molded part was measured by using three dimensional coordinate measurement machine. It was shown that temperature control factor has more significant effect on the warpage of mobile phone cover than pressure control factor.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.8
• /
• pp.1057-1064
• /
• 2004

Silk, polyester, cotton, and wool fabrics were embroidered with varying stitch length of 3mm, 5mm, and 10mm to examine the difference in fabric shrinkage in terms of sewing direction, fabric thickness, cover factor, stitch length, and fiber type. Warp, filling, and bias direction of sewing resulted in no difference in fabric shrinkage. Within the samples with same stitch length, there was less fabric shrinkage in fabrics with higher fabric thickness or higher cover factor. There was larger shrinkage when sewn with longer stitch length. Comparing fabrics with different fiber types but similar fabric thickness, silk and polyester fabrics showed the smallest fabric shrinkage and wool fabrics showed the largest shrinkage. It is shown that similar fabric shrinkage between silk and polyester is due to the similarity in cover factor.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.30 no.6_2
• /
• pp.653-663
• /
• 2012

Using soft classification, it is possible to obtain the land cover proportions from the remotely sensed image. These land cover proportions are then used as input data for a procedure called "super-resolution mapping" to produce the predicted hard land cover layers at higher resolution than the original remotely sensed image. Superresolution mapping can be implemented using a number of algorithms in which the Hopfield Neural Network (HNN) has showed some advantages. The HNN has improved the land cover classification through superresolution mapping greatly with the high resolution data. However, the super-resolution mapping is based on the spatial dependence assumption, therefore it is predicted that the accuracy of resulted land cover classes depends on the relative size of spatial features and the spatial resolution of the remotely sensed image. This research is to evaluate the capability of HNN to implement the super-resolution mapping for SPOT image to create higher resolution land cover classes with different zoom factor.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.3
• /
• pp.1-9
• /
• 2010

Since the horizontal global radiation and cloud cover are a main factor for designing any solar photovoltaic system, it is necessary to evaluate its characteristics all over the country. The work presented here are the investigation of horizontal global radiation and cloud cover in Korea. The data utilized in the investigation consist of horizontal global radiation and cloud cover collected for 27 years(1982. 12~2008. 12) at measuring stations across the country. The analysis shows that the annual-average daily horizontal global radiation is $3.61\;kWh/m^2$ and the annual-average daily cloud cover is 5.1 in Korea. We also constructed the contour map of cloud cover in Korea by interpolating actually measured data across the country.