• Journal of information and communication convergence engineering
• /
• v.14 no.4
• /
• pp.246-251
• /
• 2016

In this study, we developed a reduced 94 GHz hybrid ring coupler on a GaAs substrate in order to demonstrate the possibility of the integration of various passive components and MMICs in the millimeter-wave range. To reduce the size of the hybrid ring coupler, we used multiple open stubs on the inside of the ring structure. The chip size of the reduced hybrid ring coupler with multiple open stubs was decreased by 62% compared with the area of the hybrid ring coupler without open stubs. Performance in terms of the loss, isolation, and phase difference characteristics exhibited no significant change after the use of the multiple open stubs on the inside of the ring structure. The reduced hybrid ring coupler showed excellent coupling loss of $3.87{\pm}0.33dB$ and transmission loss of $3.77{\pm}0.72dB$ in the measured frequency range of 90-100 GHz. The isolation and reflection were -48 dB and -32 dB at 94 GHz, respectively. The phase differences between two output ports were $180^{\circ}{\pm}1^{\circ}$ at 94 GHz.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.3_1spc
• /
• pp.566-572
• /
• 2013

In this study, a collision simulator for rolling stock that considers the plastic deformation of the car body and the dynamic characteristics of a coupler system was developed using Matlab/Simulink. Normally, a coupler system has functions for both connecting the individual car bodies and absorbing the impact energy. A coupler system is composed of a rubber buffer, hydraulic buffer, and deformation tube elements. The coupler system should protect the car body and prevent damage when the shunt speed is less than 10 km/h, which is the regulation speed based on the safety rule for rolling stock. However, if the shunt speed is greater than 10 km/h, a car body is plastically deformed. Therefore, the modeling of the plastic deformation of a car body should be included in a simulator. This collision simulator can provide the design parameters for a coupler system and car body.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.6
• /
• pp.598-604
• /
• 2011

A method of miniaturizing branch line coupler with connected coupled lines is presented. The quarter-wavelength transmission lines in the typical microstrip branch line coupler are replaced with the connected coupled lines with same characteristics of ones for compact size. The connected coupled line is analyzed by T-equivalent circuit and Z parameters based on the even-odd mode analysis. The proposed branch line couplers with connected coupled line are designed and fabricated on FR4 substrate at 2.4 GHz. The measured results show good agreement with theoretical prediction. And the experimental results show that the size of coupler is 37 precent smaller than conventional coupler. This minimized coupler is suitable for Butler Matrix as feeder for mobile communication beam forming antenna.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.147-151
• /
• 2009

A wideband correlator, with 45% relative bandwidth is proposed at the frequency range of 3.1-5.1GHz. The structures of the correlator components such as the delay line and the Wilkinson power divider are designed to be realized in transmission line form using the Agilent's Advanced Design System (ADS). The correlator made by using three unique wideband 3-dB couplers, rat-race coupler and one 3-dB wilkinson power divider to reach the required bandwidth. The insertion loss, amplitude imbalance and phase imbalance between ports are presented. The proposed correlator makes compact size better than correlator of conventional structure.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.68-70
• /
• 2015

The four-port coupler circuit consists of input port, isolation port and two output ports. When it inserts a signal at the input port and the isolation port, the magnitude and phase of the output signal at two output ports are decided by the magnitude and phase of the input signal. This paper analyzes the output signal characteristic of two output ports due to the input signal magnitude and phase of two input ports using the typical 4-port coupler circuit, Branchline hybrid coupler and Ring-hybrid coupler. And, it studies about new way to use branchline hybrid coupler and ring-hybrid coupler on the basis of the this information.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.1
• /
• pp.123-130
• /
• 2009

The partial discharge (PD) measurement is a very effective method to assess the winding insulation condition of high-voltage machines, since most of the insulation failure processes are directly or indirectly caused by PD. On-line PD measurements, which can detect insulation defects of winding in the early stages on rotating machines in operation, have been accepted as the most important technique. The epoxy mica capacitive coupler is currently and extensively used for on-line detection of PD pulses of high-voltage rotating machines. To evaluate the feasibility of developing a capacitive coupler that is easier to manufacture at a lower cost compared to epoxy mica couplers, a 100pF capacitive coupler made of ceramic material is designed, fabricated and tested for on-line PD measurements of 23 kV electrical machines. A series of electrical tests and accelerated aging tests are performed on the ceramic coupler to evaluate the performance requirements, long-term reliability and thermal stability for in field application. The test results show that the newly developed ceramic coupler provides equal and improved performance at a lower cost compared to epoxy mica couplers, and estimated voltage life is anticipated to surpass 100 years.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.5
• /
• pp.238-242
• /
• 2001

In this paper, we extracted design parameters for re-entrant mode microstrip directional coupler using FE(finite element) calculations. The microstrip directional coupler suffers from a poor directivity due to effect of the inhomogeneous dielectric including both dielectric substrate and air in microstrip transmission lines. Thus, the phase velocity of even mode is not equal to that of odd mode. In order to improve the directivity of microstrip directional coupler, a novel re-entrant mode microstrip directional coupler was employed. In microstrip configuration, the high directivity can be reached by matching the even- and odd-mode effective phase velocities. Through the values of capacitance obtained from 2-dimensional FE calculations, the phase velocities for each mode and the design parameter were extracted for the proposed parallel coupled-line configuration. Based on the extracted design parameter with phase matching condition, we designed and fabricated a 30dB directional coupler at 0.85GHz. Experimental results show good performance with excellent, isolation and directivity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1028-1033
• /
• 2006

In general the cooling of projection TV is realized with aluminum coupler and coolant. A new type of projection TV with plastic coupler is discussed. Compared with an aluminum coupler, the plastic coupler has the advantage of cost, but is not as good as aluminum one in cooling performance. Therefore it is thought that there may be some problems such as brightness degradation induced by insufficient cooling andit is needed to investigate the relation between phosphor brightness and temperature variation. In this paper, a procedure is developed to predict the brightness degradation of CRT in projection TV with plastic coupler. Thermal analysis for CRT in projection TV is performed using FEM (finite element method).

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.66-71
• /
• 2021

A hydraulic quick coupler is a component used to easily connect or disconnect pipes or hoses that transfer high pressure fluid without leakage in various mechanical devices. In this study, to obtain an optimal design of a 3/8" hydraulic quick coupler, the effect of different shapes of the internal piston on the internal flow characteristics of the coupler was analyzed and evaluated through numerical analysis based on computational fluid dynamics. Subsequently, the optimal shape design of the internal piston was obtained by comparing the flow characteristics results such as velocity distribution, temperature distribution, and the pressure drop of the hydraulic quick coupler.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.1
• /
• pp.87-93
• /
• 2014

A tightened coupler with two way-threading is suggested to overcome the previous one-way threaded coupler. The experiment and a mock-up test were conducted to analyze the constructability of the suggested coupler. The aim of the mock-up test was to assemble the suggested coupler in horizontal rebar of mat footing and vertical rebar of semi-fabricated column bars. The method using the suggested coupler in semi-fabricated column bars is developed by analyzing the problem of fabricated column bars using the one-way threaded coupler. The result of the mock-up test showed that the time required to assemble the suggested coupler in the horizontal bars is shorter than it is for the one-way threaded coupler. In addition, the method using the suggested coupler in semi-fabricated column bars has advantages such as lower working loads, supporting safe work and strongly tightening the rebar. From these results, it is revealed that the suggested coupler is adequate to use in rebar work in terms of cost, quality and time.