• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.1
• /
• pp.23-28
• /
• 2008

Flow analysis in a turbine cascade by Euler or Navier-Stokes equation gives relatively accurate solution, however, those method require large computer memory or computing time. On contrast, the panel method, which is applied to incompressible and inviscid flow, provides fast and reasonal solution but the compressibility correction is required for a high air velocity case. In this paper, the compressibility corrected panel method was applied in order to find velocity distribution on turbine blades. Results showed that the calculated velocity in a turbine cascade by the compressibility corrected panel method gave good agreement with the solution by finite volume method for compressible flow.

• Korean Journal of Remote Sensing
• /
• v.14 no.1
• /
• pp.69-82
• /
• 1998

SAR imagery can overcome the limitations of electro-optical sensor imagery and provide us Information which plays a supplementary role. But it is necessary to remove a variety of geometric errors in SAR imagery. An accurate geometric correction of SAR imagery is not easy task to achieve, though some techniques and theories are introduced. We also have difficulties such as transformation problem between 'International' ellipsoid in Radarsat system and 'Bessel' ellipsoid. Two widely used correction method, one is made by simulated image, and the other by collinearity equation, usually use DEM. In this study, the merits and demerits of geocoding methods respectively and the effective method for Korean terrain were found.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.2
• /
• pp.141-152
• /
• 2018

The heating process such as line heating, triangular heating and so on is widely used in plate forming of shell plates found in bow and stern area of outer shell in a ship. Local shrinkage during heating process is main physical phenomenon used in plate forming process. As it is well appreciated, the heated plate undergoes the change in material and mechanical properties around heated area due to the harsh thermal process. It is, therefore, important to investigate the changes of physical and mechanical properties due to heating process in order to use them plate the design stage of shell plates. This study is concerned with the development of formula of plastic hardening constitutive equation for steel plate on which line heating is applied. In this study the stress correction formula for the heated plate has been developed based on the numerical simulation of tension test with varying plate thickness and heating speed through the regression analysis of multiple variable case. It has been seen the developed formula shows very good agreement with results of numerical simulation. This paper ends with usefulness of the present formula in examining the structural characteristic of ship's hull.

• Korean Journal of Optics and Photonics
• /
• v.34 no.2
• /
• pp.61-65
• /
• 2023

This paper studies a method of applying pre-distortion to the image mask of the gobo illumination optical system to correct an irradiated image and irradiate a clear image. In the case of the gobo illumination optical system, since it is generally irradiated with a tilt, distortion in the upper and lower directions occurs severely in the image. To solve this problem, the correction coordinates of the image were derived using a proportional equation, and the distortion was corrected by applying them to the image mask. As a result, it was confirmed that the distortion was reduced by 64.5% compared to the case of using the existing image mask.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.39-44
• /
• 2008

Stress wave propagation plays an important role in many engineering problems for reducing industrial noise and vibrations. In this paper, the dispersion-corrected finite element model is proposed for reducing the dispersion error in simulation of stress wave propagation. At eliminating the numerical dispersion error arising from the numerical simulation of stress wave propagation, numerical dispersion characteristics of the wave equation based finite element model are analyzed and some dispersion control scheme are proposed. The validity of the dispersion correction techniques is demonstrated by comparing the numerical solutions obtained using the present techniques.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.98-103
• /
• 2001

In case that electronic ballast employing a valley-fill passive power factor correction (PFC) circuit is used for feeding fluorescent lamps, a new method to reduce crest factor of the lamp current is studied in this paper. In order to reduce crest factor to lower value, a pulse frequency modulation technique based on the waveform of the dc-link voltage which is predetermined by the passive PFC circuit, is taken into the switching control action of the electronic ballast. An equation-based analysis between the crest factor of lamp current and the effect of varying the inverter switching frequency is comprehensively performed.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.5 no.3
• /
• pp.54-63
• /
• 1991

This paper describes an effort to develope a microcomputer-based parameter measurement system for a brushless DC motor. Back EMF equation is derived from back EMF waveform of a brushless DC motor. To minimize error the due to the ripple component in the measured armature current, digital averaging filter is employed. The whole identification process of signal generation, measurement parameter determination is fully automated. A new identification algorithm for the brushless DC motor parameters is developed. New parameter correction method is proposed using the deadzone current and the time to reach the peak current. In the proposed correction method, the measured current is in excellent agreement with the estimated current.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.6
• /
• pp.1115-1120
• /
• 1992

The apparent negative crack growth phenomenon which usually arises in partial unloading compliance test is well known. The reason for apparent negative crack growth is the compressive residual stress caused by the plastic zone around the crack tip. The phenomenon as a possible source of error in determining $J_{JC}$ or J-R curve from partial unloading compliance experiments may be eliminated by the correction of compliance. A compliance correction equation is derived from a stress field analysis near the crack tip.

• Journal of the Korean Data and Information Science Society
• /
• v.18 no.1
• /
• pp.73-80
• /
• 2007

Cointegration(together with VARMA(vector ARMA)) has been proven to be useful for analyzing multivariate non-stationary data in the field of financial time series. It provides a linear combination (which turns out to be stationary series) of non-stationary component series. This linear combination equation is referred to as long term equilibrium between the component series. We consider two sets of Korean bivariate financial time series and then illustrate cointegration analysis. Specifically estimated VAR(vector AR) and VECM(vector error correction model) are obtained and CV(cointegrating vector) is found for each data sets.

• Journal of Industrial Technology
• /
• v.16
• /
• pp.131-137
• /
• 1996

For a large scale civil and architectural structures, mainly steel, concrete and aluminum have been used and weight and corrosion of materials became a major concern. Designing with composite materials is very much complicated. Simple classical theory may yield good results for selecting "initial" sections for preliminary design. D. H. Kim proposed to use the quasi-isotropic constants by Tsai for the preliminary design of the composite primary structures for the civil construction. Also he made simple equation using correction factor. In this paper, the simple formulas developed by D. H. Kim to obtain "exact" values of the natural frequencies of [ABBCAAB]r laminate are compared with Whitney's equations. Also natural frequencies of the plate with varying aspect ratios and reinforcing fiber orientations, are compared with natural frequencies of bean. This work can be a guideline to obtain data in many other cases.