• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.2
• /
• pp.213-220
• /
• 2016

This research aims to develop core technologies for passive carrier (no power in carrier itself) transfer system. The technologies are passive levitation, propulsion, and guidance, which can be great benefits for semiconductor and display manufacturing industries. Passive maglev carrier is necessary to precise position control for quiet and stable transfer operation. However, the structural characteristics of carrier and the installation errors of gap sensors cause the pitch motion. Hence, the controller design in consideration of pitch motion is required. This study deals with the reduction control of carrier pitch motion. PDA controller and PDA controller with pitch control are proposed to compare the pitch angle analysis. The pitch angle and the levitation precision are measured by experiment. Finally, the optimized design of pitch controller is presented and the effects are discussed.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.47-56
• /
• 2015

In this paper, the Thermal behavior and reliability characteristics of carbon CCL (Copper Claded Layer), which can be used as the core of HDI (High Density Interconnection) PCB (Printed Circuit Board) are evaluated through experiments and numerical analysis using CAE (Computer Aided Engineering) software. For the characterization of the carbon CCL, it is compared with the conventional FR-4 core and Heavy Cu core. From research results, the deformation amount of the flexure strength of PCB is the highest with pitch grade carbon and thermal behavior of PCB is lowest as temperature increases. In addition, TC (Thermal Cycling), LLTS (Liquid-to-Liquid Thermal Shock) and Humidity tests have been applied in the PCB with carbon core and the reliability of PCB with carbon core is confirmed through reliability tests. Also, possibility of uneven surface of the via hole and wear of the drill bit due to the carbon fibers are analyzed. surface of the via hole is uniform, the surface of the drill bit is smooth. Therefore, it is proved that the carbon CCL has the drilling workability of the same level as conventional core material.

• Nuclear Engineering and Technology
• /
• v.49 no.1
• /
• pp.1-5
• /
• 2017

The heavy water zero power reactor (HWZPR), which is a critical assembly with a maximum power of 100 W, can be used in different lattice pitches. The last change of core configuration was from a lattice pitch of 18-20 cm. Based on regulations, prior to the first operation of the reactor, a new core was simulated with MCNP (Monte Carlo N-Particle)-4C and WIMS (Winfrith Improved Multigroup Scheme)-CITATON codes. To investigate the criticality of this core, the effective multiplication factor ($K_{eff}$) versus heavy water level, and the critical water level were calculated. Then, for safety considerations, the reactivity worth of $D_2O$, the reactivity worth of safety and control rods, and temperature reactivity coefficients for the fuel and the moderator, were calculated. The results show that the relevant criteria in the safety analysis report were satisfied in the new core. Therefore, with the permission of the reactor safety committee, the first criticality operation was conducted, and important physical parameters were measured experimentally. The results were compared with the corresponding values in the original core.

• Nuclear Engineering and Technology
• /
• v.55 no.1
• /
• pp.330-338
• /
• 2023

In this study, impacts of an enhanced-moderation Fuel Assembly (FA) named Truly Optimized PWR (TOP) lattice, which is modified based on the standard 17 × 17 PWR FA, are investigated in a natural circulation Soluble-Boron-Free (SBF) Small Modular Reactor (SMR). Two different TOP lattice designs are considered for the analysis; one is with 1.26 cm pin pitch and 0.38 cm fuel pellet radius, and the other is with 1.40 cm pin pitch and 0.41 cm fuel pellet radius. The NuScale core design is utilized as the base model and assumed to be successfully converted to an SBF core. The analysis is performed following the primary coolant circulation loop, and the reactor is modelled as a single channel for thermal-hydraulic analyses. It is assumed that the ratio of the core pressure drop to the total system pressure drop is around 0.3. The results showed that the reactor power could be increased by 2.5% and 9.8% utilizing 1.26/0.38 cm and 1.40/0.41 cm TOP designs, respectively, under the identical coolant inlet and outlet temperatures as the constraints.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.4
• /
• pp.40-47
• /
• 1988

Our plywood manufacturing industries which entertained prosperous stage in late 1970's have come to be in face of the problems of conceedingly obtaining good quality logs and yield up-grading, which is considered by future-replaceable forest resources. In view of this point, manufacturing characteristic on softwood plywood using Japanese larch, pitch pine as domestic plantation species, and western hemlock as foreign species was studied. In this study, veneer- and plywood manufacturing yields were discussed in relation to log properties and veneer defects (knots). The summarized conclusions were as follows: 1. The majority of sample logs belonged to second grade on the standard. And, eccentricity of larch was the highest 11%, about 2 times those of pitch pine, hemlock. 2. Knot frequency of occurrence of larch reached 19% within log height 8m, and pitch pine 13% within 4m. Correspondingly, the log height of larch available for plywood manufacture was higher by about 2 times that of pitch pine. 3. In the knot types, most of knots of larch appeared dead, whereas those of pitch pine and hemlock appeared live. In size of knots, larch and hemlock showed relatively small 1-2cm dia. by 70% or more and pitch pine did the larger 24cm by 65%. Generally the more knot emerged in the inner side of veneer than the outer. 4. Plywood manufacturing yields by peeling with spindle revolution lathe were 37% in larch > 32% in hemlock> 26% in pitch pine. S. Jointed core veneer yields by peeling with outer perimeter back-up lathe were 55% in hemlock> 53% in larch> and 48% in pitch pine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.135-140
• /
• 2010

An important goal in diesel engine research is the development of a means to reduce the emissions of nitrogen oxides (NOX). The use of a cooled exhaust gas recirculation (EGR) system is one of the most effective techniques currently available for reducing nitrogen oxides. Since Particular Matter (PM) fouling reduces the efficiency of an EGR cooler, a trade-off exists between the amount of NOX and PM emissions, especially at high engine loads. In the present study, engine dynamometer experiments have been performed to investigate the heat exchange characteristics of the stack-type EGR coolers with wave fin pitches of 3.6 and 4.6 mm. The results show that the heat exchange effectiveness is decreased as surface area decrease with pitch of 4.6 mm due to PM fouling. As surface area increase at pitch of 3.6 mm, super-cooling happens in the recirculated exhaust gas.

• Computers and Concrete
• /
• v.31 no.6
• /
• pp.527-536
• /
• 2023

Fiber Reinforced Polymer (FRP) bar has emerged as a viable and sustainable replacement to steel in reinforced concrete (RC) under severe corrosive environment. The behavior of concrete columns reinforced with FRP bars, spirals, and hoops is an ongoing area of research. In this study, 3D nonlinear numerical modelling of circular concrete columns reinforced with Glass Fiber Reinforced Polymer (GFRP) bars and transversely confined with GFRP spirals were conducted using fracture-plastic model. The numerical models and experimental results are found to be in good agreement. The effectiveness of confinement was accessed through von-mises stresses, and it was found that the stresses in the concrete's core are higher with a 30 mm pitch (46 MPa) compared to a 60 mm pitch (36 MPa). The validated models are used to conduct parametric studies. In terms of axial load carrying capacity and member ductility, the effect of concrete strength, spiral pitch, and longitudinal reinforcement ratio are thoroughly investigated. The confinement effect and member ductility of a GFRP RC column increases as the spiral pitch decreases. It is also found that the confinement effect and member ductility decreased with increase in strength of concrete.

• Journal of the Korean Ceramic Society
• /
• v.43 no.7 s.290
• /
• pp.439-444
• /
• 2006

Artificial graphite generally manufactured by carbonization sintering of shape-body of kneaded mixture using granular cokes as filler and pitch as binder, going through pitch impregnation process if necessary and finally applying graphitization heat treatment. Graphite materials are used for core internal structural components of the High-Temperature Gas-cooled Reactors (HTGR) because of their excellent heat resistibility and resistance of crack progress. The HTGR has a core consisting of an array of stacked graphite fuel blocks are machined from IG-110, a high-strength, fine-grained isotropic graphite. In this study, crack stabilization and micro-structures were measured by bend strength and fracture toughness of isotropic graphite grade IG-110. It is important to the reactor designer as they may govern the life of the graphite components and hence the life of the reactor. It was resulted crack propagation, bend strength, compressive strength and micro-structures of IG-110 graphite by scanning electron microscope and universal test machine.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3665-3674
• /
• 2021

One of the important parts of the in-core fuel management is loading pattern optimization (LPO). The loading pattern optimization as a reasonable design of the in-core fuel management can improve both economic and safe aspects of the nuclear reactor. This work proposes the hybrid of fuzzy logic controller with harmony search algorithm (HS) for loading pattern optimization in a pressurized water reactor. The music improvisation process to find a pleasing harmony is inspiring the harmony search algorithm. In this work, the adjustment of the harmony search algorithm parameters such as the bandwidth and the pitch adjustment rate are increasing performance of the proposed algorithm which is done through a fuzzy logic controller. Hence, membership functions and fuzzy rules are designed to improve the performance of the HS algorithm and achieve optimal results. The objective of the method is finding an optimum core arrangement according to safety and economic aspects such as reduction of power peaking factor (PPF) and increase of effective multiplication factor (Keff). The proposed approach effectiveness has been tried in two cases, Michalewicz's bivariate function problem and NEACRP LWR core. The results show that by using fuzzy harmony search algorithm the value of the fitness function is improved by 15.35%. Finally, with regard to the new solutions proposed in this research it could be used as a trustworthy method for other optimization issues of engineering field.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.4
• /
• pp.379-382
• /
• 2014

In this paper, the cogging torques were calculated for 1kw double-sided axial flux permanent magnet (AFPM) generator with different stator core pole arrangements. The generator is composed of 18 stator pole and 24 rotating field magnets on each side. The cogging torques of the generator with three types of arrangements of stator poles were calculated using 3D finite element method and the optimum core shape was determined to minimize the cogging torque.