• 전기학회논문지
• /
• 제65권1호
• /
• pp.65-72
• /
• 2016

This paper presents the analysis of the analysis of thrust characteristics of linear induction motors(LIMs) according to secondary reaction plate. LIMs are well known as high speed transport systems, which can obtain thrust directly without gears and links, or auxiliary mechanisms. A simple structure, easy maintenance, and less environmental pollution are advantages of LIMs. In transport systems using LIMs, the secondary reaction plate is an important design factor, because it has considerable impact on the cost of the railway as well as the performance of the LIMs. This paper deals analyzed the characteristics of linear induction motor used for moving the vehicle of container scanner. Thrust, efficiency and load characteristic were interpreted with FEM regarding two models whose material of secondary reaction plate was copper and aluminum. It suggested the interpretation of thrust, efficiency and power factor characteristic along slip and compared the operation ability of linear induction motor through characteristics analysis along the load.

• 한국생산제조학회지
• /
• 제20권1호
• /
• pp.81-85
• /
• 2011

Recently, the electronic parts are to be thinner plate, smaller size, light weight material and CPU, HDD and DRAM in all the parts have been produced on the basis of the high speed and greater capacity. Also, conventional goods have replaced a LED (Light-Emitting Diode) in lighting products so; such industry devices need to have cooling. To maximize all the performance on the heat-radiated products, the area of heat-radiated parts is required to be cooled for keeping the life time extension and performance of product up. Existing cooling systems are using radiant heat plate of aluminum, brass by extrusion molding, heat pipe or hydro-cooling system for cooling. There is a limitation for bringing the light weight of product, cost reduction, molding of the cooling system. So it is proposed that an alternative way was made for bringing to the cooling system. EP (Engineering Plastic) of low-cost ABS (Acrylonitrile butadiene styrene Resin) and PC (Polycarbonate) was coated with brass and the coating made the radiated heat go up. The performance of radiant heat plate is the similar to the existing part. We have studied experimentally on the radiated heat plate for the light-weight, molding improvement and low-cost. From now on, we are going to develop the way to replace the exiting plate with exterior surface of product as a cooling system.

• 박물관보존과학
• /
• 제12권
• /
• pp.35-45
• /
• 2011

국립중앙박물관에서는 일제 강점기에 발굴된 미정리유물 정리사업의 일환으로 서봉총(瑞鳳塚), 식리총(飾履塚), 금령총(金鈴塚) 출토 행엽(杏葉) 중 일부를 선별하여 보존처리 및 제작기법을 연구하였다. 선별된 행엽은 편원어미형(扁圓魚尾形), 심엽형(心葉形), 이형(異形)으로 구분할 수 있으며 실체현미경관찰 및 XRF, SEM-EDS 분석결과 지판(地板)의 재질은 철(Fe)이며, 상판(上板) 및 문양판의 재질은 철(Fe), 구리(Cu), 은(Ag)이 각각 확인되었다. 편원어미형과 십자문심엽형행엽의 경우 세 분묘 모두 제작기법과 크기가 동일한 행엽이 각각 철(Fe)과 구리(Cu)로 제작된 것이 특징이다. 도금층이 존재하지 않는 이형행엽을 제외한 나머지 행엽의 도금층은 수은아말감도금이었다.

• 한국정보통신학회논문지
• /
• 제12권1호
• /
• pp.25-32
• /
• 2008

본 논문에서는 초고속 광대역 서비스를 제공하기에 적합한 주파수 대역인 60GHz 밀리미터파대역의 전파특성을 파악하기 위하여 직접 파를 제외한 반사파 및 투과파에 대한 신호세기를 측정하여 평균 전력 및 표준 편차를 분석하였다. 먼저, 장애물 투과에 의한 수신 신호 세기를 분석 한 결과, 철문, 동판 등은 약 40dB이상의 투과 손실치를 나타내어 투과가 거의 발생하지 않았으며, 고무, 스티로폼 및 유리등이 약 3dB의 투과 손실치로 가장 적게 나타났다. 입사각이 60도 인 경우 장애물에 의한 반사파 수신신호세기는 파티션에서의 손실치가 약 22dB로서 크게 나타났으며, 벽면 반사 손실치가 약 6dB로 가장 적게 나타났다. 이상의 결과는 반사파와 투과파가 서비스 영역 결정에 영향을 미치는 WPAN과 같은 피코셀 이동통신망의 설계에 이용될 수 있을 것으로 판단된다.

• 한국태양에너지학회 논문집
• /
• 제33권3호
• /
• pp.27-35
• /
• 2013

One of the most important factors that have a large influence on performance of the solar water heater system is performance of the solar collector, more detailedly, coating technology on the surface of the solar collector, which can provide high solar absorptance and low emittance. The core of the coating technology is to coat solar selective surfaces. In this study, various performance experiments are carried out using $Cr_2(SO_4)_3{\cdot}15H_2O$ coating technology. Here, IGBT(Insulated Gate Bipolar Transistor) of 5000A-15V was used as the surface processing rectifier which can stably output power and also can control voltage and current. The plating solution mainly contains black chrome$^{+3}$ concentration, H-y Conductivity, N-u Complex, NF Additive and NC-2 Wetter. Before applying the black chrome coating on the copper plate, optimal conditions are provided by using various preprocessing methods such as removal of fat, activation, electrolytic polishing, nickel strike, copper sulfate plating and bright neckel plating, and then the automatic continuous coating experiment are performed according to plating time and cathode current density. In the experiment, after the removal of fat, chemical polishing, nickel strike and activation processes as the preprocessing methods, the black chrome coating was performed in a plate solution temperature of $28^{\circ}C$ and a cathode current density of $18A/cm^2$ for 90 seconds. The thickness of chrome and nickel on the coated plate is $0.389{\mu}m$, $159{\mu}m$ respectively. As a result of the coating experiment, it showed the most excellent performance having a high solar absorptance of 98% and a low emittance of $5{\pm}1%$ when the black chrome surface had a thickness of $0.398{\mu}m$.

• Smart Structures and Systems
• /
• 제22권6호
• /
• pp.727-741
• /
• 2018

To mitigate vibrations, tuned mass dampers(TMD) are widely used for long span bridges or high-rise buildings. Due to some durability concerns, such as fluid degradation, oil leakage, etc., the alternative solutions, such as the non-contacted eddy current damping (ECD), are proposed for mechanical devices in small scales. In the present study, a new eddy current damping TMD (ECD-TMD) is proposed and developed for large scale civil infrastructure applications. Starting from parametric study on finite element analysis of the ECD-TMD, the new design is enhanced via using the permanent magnets to eliminate the power need and a combination of a copper plate and a steel plate to improve the energy dissipation efficiency. Additional special design includes installation of two permanent magnets at the same side above the copper plate to easily adjust the gap as well as the damping. In a case study, the proposed ECD-TMD is demonstrated in the application of a steel arch bridge to mitigate the wind-induced vibrations of the flexible hangers. After a brief introduction of the configuration and the installation process for the damper, the mitigation effects are measured for the ambient vibration and forced vibration scenarios. The results show that the damping ratios increase to 3% for the weak axis after the installation of the ECD-TMDs and the maximum vibration amplitudes can be reduced by 60%.

• 한국정밀공학회지
• /
• 제25권11호
• /
• pp.66-72
• /
• 2008

During the plate and foil cold rolling process, considerable values of the force of material pressure on the tool occur. These pressures cause the elastic deformation of the roll, thus changing the shape of the deformation legion. Rolled copper foils should be characterized by a good quality and light dimensional tolerances. Because of automation that is commonly implemented in flat product rolling mills, these products should meet the requirements of tightened tolerances, particularly strip thickness, and feature the greatest possible flatness. The shape of the roll gap is influenced by the elastic deformation of rolls parts of the rolling process affecter of the pressure force. However, to control roll deformation should be difficult. Because the foil thickness is very thin and the permissible deviations in the thickness of foil are small. In this paper, FE-simulation of roll deformation in thin foil cold roiling process is presented.

• 한국태양에너지학회 논문집
• /
• 제23권3호
• /
• pp.15-22
• /
• 2003

This study deals with the collection of solar energy and its storage in evacuated tubular collector systems for different types of header design, flow passage and heat transfer devices. In order to elicit the most efficient combination of header design, flow passage, heat transfer hardware and operating conditions, a series of tests were done for the four different types of solar collectors utilizing vacuum tubes. The systems studied here either has the evacuated collector tubes with a metal cap on one end or the all-glass evacuated solar collector tubes These evacuated tubular collectors are known to be more efficient than the flat-plate ones in both direct and diffuse solar radiation. Test results show that the system comprised of the all-glass evacuated tubes with U-shaped copper pipes inside outperforms the other configurations. Especially, a rolled copper sheet tightly placed along the inner surface of each inner tube enhances heat transfer between the heated collector surface and the water contained in the U-shaped copper pipe.

• 한국응용과학기술학회지
• /
• 제35권3호
• /
• pp.612-621
• /
• 2018

본 연구에서는 전기분해 방법을 이용한 질산성질소($NO_3{^-}-N$) 분해가 $TiO_2$ nanotube plate 및 구리, 니켈, 스테인리스 스틸, 알루미늄, 주석, 티타늄을 환원전극으로 사용하였을 때 가능한지를 평가하였다. 전극의 전기화학적 특성 평가는 임피던스 측정을 하여 비교하였고, $TiO_2$ nanotube plate의 표면 분석은 주사전자현미경을 통해 SEM 및 BET 분석법을 이용한 비표면적 분석을 통해 비교하였다. 질산성질소 전해실험의 경우 90분의 실험을 진행하였으며, 실험 결과 전극 표면의 부식이 수반되지 않은 $TiO_2$ nanotube plate가 기타 금속 전극에 비해 질산성질소 환원 반응속도가 가장 뛰어난 것으로 확인되었다.

• 설비공학논문집
• /
• 제20권3호
• /
• pp.189-196
• /
• 2008

The increase of system weight due to installation of cooling devices adds electrical and mechanical loads of humanoid robot, and in return, results in much heat. Therefore, the weight of cooling system is a critical issue for robot cooling. In this study, we propose non-metallic cold plates to deal with such problems. We compare thermal performances between one metallic cold plate and five different types of non-metallic cold plates. A metallic cold plate is totally made of copper. Five non-metallic PC(polycarbonate) cold plates, which are designed to reduce the overall weight of robot cooling system, are composed of a polycarbonate cover with different types of base plate. The overall heat transfer coefficients per unit mass and thermal resistances are obtained for the cold plates. The metallic cold plate shows the best thermal performance. It is interesting to note that the PC cold plate with an aluminum base plate with 18 channels shows the best overall heat transfer coefficient per unit mass. Most polycarbonate cold plates display fairly comparable thermal performance with more reduced system weight compared to the metallic cold plate.