• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.350-355
• /
• 2009

The crysralline silicon solar cell where the solar cell market grows rapidly is occupying of about 85% or more high efficiency and low cost endeavors many crystalline solar cells. The fabricaion process of high efficiency crystalline silicon solar cells necessitate complicated fabrication processes and Ti/Pd/AG contact, This metal contacts have only been used in limited areas in spite of their good srability and low contact resistance because of expensive materials and process. Commercial solar cells with screen-printed solar cells formed by using Ag paste suffer from loe fill factor and high contact resistance and low aspect ratio. Ni and Cu metal contacts have been formed by using electroless plating and light-induced electro plating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on 0.2~0.6${\Omega}$ cm, $20{\times}20mm^2$, CZ(Czochralski) wafer.

• 한국의류산업학회지
• /
• 제20권1호
• /
• pp.101-107
• /
• 2018

The purpose of this study is to develop the electroconductive textiles based on polyurethane(PU) nanoweb and to explore that it is applicable to smart clothing. The electroconductive textiles developed by coating 2.0 wt% aqueous dispersed non-oxidized graphene paste on the surface of PU nanoweb. The fabricated electroconductive nanoweb was applied as a transmission line to connect the LED lamp, and the brightness of the LED lamp was measured to confirm its performance. The nanoweb transmission line was fixed by two methods(seam sealing tape, embroidering) to connect the LED lamp and AA batteries. The results as follows, the brightness of the LED lamp fixed with seam sealing tape was about 82 lux, and which fixed with embroidering was about 57 lux. It represents that the nanoweb transmission line which fixed with the seam sealing tape has better electrical signal transmitting because the lux value higher than the one fixed by embroidering. In order to compare the performance of the nanoweb transmission line and the metal wire, we connected the LED lamp with copper wire. The brightness of copper wire connected LED lamp was about 193 lux. Although the electrical signal strength of the nanoweb transmission line was weaker than the copper wire, it was reachable to operate LED lamp. The results of this study will provide a basic data to develop the textile based electronic devices, and conducting wire for smart clothing.

• 한국전기전자재료학회논문지
• /
• 제24권12호
• /
• pp.1010-1017
• /
• 2011

The use of plated front contact for metallization of silicon solar cell may alternative technologies as a screen printed and silver paste contact. This technologies should allow the formation of contact with low contact resistivity a high line conductivity and also reduction of shading losses. A selective emitter structure with highly dopes regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing. When fabricated Ni/Cu plating metallization cell with a selective emitter structure, it has been shown that efficiencies of up to 18% have been achieved using this technology.

• Journal of Welding and Joining
• /
• 제15권2호
• /
• pp.36-42
• /
• 1997

In this paper, stability of initial strength at solder joint with lead free solders, such as Sn-In (52-48%) and Sn-Ag (96.5-3.5wt%) was studied. To obtain at solder joint with high quality, it is very important to control the temperature at the interface of solder joints. It is found that the thermal EMF (electro motive force) occurs betwee lead frame and copper pad on a substrate during reflow soldering process using heated tip. As a result of control the temperature at interface of solder joints, variation of initial strength at solder joint decreases from about $\pm40%$ to $\pm20%$, and it is realized Pb free soldering process using Sn/In and Sn-Ag solder paste.

• Journal of Welding and Joining
• /
• 제16권5호
• /
• pp.100-107
• /
• 1998

This paper describes fluxless soldering of reflow soldering process using solder foil instead of solder pastes. There is an increasing demand for the reliable solder connection in the recent high density microelectronic components technologies. And also, it is problem fracture of an Ozone layer due to freon as which is used to removal of remained flux on the substrate. This paper discussed joining phenomena, boudability and joining processes of microelectronics devices, such as between outer lead of VLSI package and copper pad on a substrate without flux. The shear strength of joints is 8 to 13 N using Sn/Pb (63/37 wt.%) solder foil with optimum joining conditions, meanwhile, in case of using Sn/In (52/48 wt.%) solder foil, it is possible to bond with low heating temperature of 550 K, and accomplish to high bonding strength of 25N in condition heating temperature of 650K. Finally, this paper experimentally shows fluxless soldering using solder foil, and accomplishes key technology of microsoldering processes.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.107-108
• /
• 2000

We propose the method which is possible to fabricate the electrodes with the fine pattern and low resistance by photolithography and electroplating. The widths of pattern fabricated were 30, 50, 70 and 100um and the thickness could be up to $10{\mu}m$. The resistivity of the copper electrode electroplated was below $2.0{\mu}{\Omega}$ cm which is about half of photosensitive silver electrode. Dielectric layer was coated on the electrodes by screen printing and the pores harmful to the discharge were not formed after heat treatment. In the viewpoint of resistance and patterning, this method has much higher potential for large area display than other methods like screen printing, photosensitive conductive paste method and sputtering.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1076-1077
• /
• 2006

Conductive pastes consist of conductive fillers( Au, Ag, Ni, Cu etc.), organic binders, solvents and additives. Meanwhile, there are some metal powders such as copper, nickel etc that are used for pastes which have serious surface corrosion problems. This problem leads to change of the color and decrease in conductivity and affect storage stability of conductive pastes. By using silane coupling agent and dispersion agent, we can ensure both the corrosion stability and long term storage stability, and enhance the high performance electrical and mechanical properties of EMI shielding silicone sealant.

• 대한화학회지
• /
• 제40권5호
• /
• pp.341-346
• /
• 1996

$(Cin)Cu(NO_3)_2$으로 변성된 턴소반죽전극을 제작하여 $I^-$이온을 벗김전압전류법을 이용하여 정량하였다. $I^-$이온은 변성제인 $(Cin)Cu(NO_3)_2$착물에 배위된 $NO_3^-$와 이온교환에 의해 변전극에 감응하며, 산화전위는 +0.72 V였다, $I^-$ 이온의 최적분석 조건은 다음과 같다: 농축용액의 조성은 0.1 M $KNO_3$, 농축시간은 10분, 탄소분말에 대한 변성제의 함량은 40%(w/w). 선형주사 양극벗김전압전류법(Linear Sweep Anodic Stripping Voltammetry)에 의한 $I^-$이온의 검출한계는 $1.0{\times}10^{-6}M$이며, $2.0{\times}10^{-5}M$에서 구한 상대표준편차는 ${\pm}5.5%$였다. 여러 음이온에 대하여 방해작용을 검토한 결과 $Cl^-,\;Br^-,\;C_2O_4^{2-},\;ClO_4^-$ 등은 $I^-$이온의 정량에 영향을 주지 않았지만, $SCN^-$ 이온은 $I^-$ 이온의 산화전류를 약 32% 감소시켰다.

• 한국표면공학회지
• /
• 제49권1호
• /
• pp.54-61
• /
• 2016

Screen printing of commercially available Ag paste is the most widely used method for the front side metallization of Si solar cells. However, the metallization using Ag paste is expensive and needs high temperature annealing for reliable contact. Among many metallization schemes, Ni/Cu/Sn plating is one of the most promising methods due to low contact resistance and mass production, resulting in high efficiency and low production cost. Ni layer serves as a barrier which would prevent copper atoms from diffusion into the silicon substrate. However, Ni based schemes by electroless deposition usually have low thermal stability, and require high annealing process due to phosphorus content in the Ni based films. These problems can be resolved by adding W element in Ni-based film. In this study, Ni-W-P alloys were formed by electroless plating and properties of it such as sheet resistance, resistivity, specific contact resistivity, crystallinity, and morphology were investigated before and after annealing process by means of transmission line method (TLM), 4-point probe, X-ray diffraction (XRD), and Scanning Electron Microscopy (SEM).

• 한국재료학회지
• /
• 제19권7호
• /
• pp.349-355
• /
• 2009

Metal thin film patterns on a LTCC substrate, which was connected through inner via and metal paste for electrical signals, were formed by a screen printing process that used electric paste, such as silver and copper, in a conventional method. This method brought about many problems, such as non uniform thickness in printing, large line spaces, and non-clearance. As a result of these problems, it was very difficult to perform fine and high resolution for high frequency signals. In this study, the electric signal patterns were formed with the sputtered metal thin films (Ti, Cu) on an LTCC substrate that was coated with protective oxide layers, such as $TiO_2$ and $SiO_2$. These electric signal patterns' morphology, surface bonding strength, and effect on electro plating were also investigated. After putting a sold ball on the sputtered metal thin films, their adhesion strength on the LTCC substrate was also evaluated. The protective oxide layers were found to play important roles in creating a strong design for electric components and integrating circuit modules in high frequency ranges.