• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.23-30
• /
• 2016

In this study, the heat transfer and pressure drop characteristics were evaluated for multi-tube $CO_2$ water heaters with lengths of 4.5 m and 7.5 m. The evaluation was done using the -NTU method, and the results were compared with experimental data. Water flows through the shell side of the water heater, while $CO_2$ flows through 8 inner tubes. The heater uses a counter-current design to maximize the heat transfer efficiency. The energy balance equation describing the flows of $CO_2$ and water for each node is set up using the section-by-section method. The calculated heat transfer rates agree well with the experimental data within ${\pm}5%$ error. The outlet water temperature decreased linearly with the increase of the water flow rate. The calculated heat transfer rates agreed well with the experimental data within ${\pm}3%$ error. The results show that the heat transfer rate increases almost linearly with the increase of water flow rate or $CO_2$ inlet temperature in both the 4.5-m and 7.5-m water heaters, whereas the water outlet temperature linearly decreases with the increase of the water flow rate. The comparison of the $CO_2$ pressure drop between the calculation and experiment results shows good agreement at the high $CO_2$ flow rate within 5 % error, but the value is about 20 % higher in the experimental pressure drop at the low $CO_2$ flow rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.201-209
• /
• 2020

In this study, issues related to changes in base year, which have controversial effects on fees in service contracts, were reviewed. In this regard, sensitivity analysis was conducted on the effects of changes in base year on conversion factor by type. The benefits and disadvantages of each specific type of medical institution were examined. Main conclusions are as follows. First, changing the base year to be closer to the present time had a beneficial effect on the conversion factor of hospitals. Second, changing the base year to be closer to the current point of time had an adverse effect on the conversion factor of pharmacies and clinics and had a significant adverse effect on clinics. Third, assuming that a single conversion factor is collectively applied to all types, a favorable effect occurred in all cases when the base year was changed to be closer to the present time. Base year changes can bring about conflicts of interest between insurer and providers, and within providers. Therefore, changing the base year should be pursued upon mutual agreement on a reasonable basis for resource allocation. In addition, it is necessary to provide incentives for temporary compensation for the types of losses incurred.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2527-2536
• /
• 2015

This study of the data of the high school judo player is subject to induction leader leadership athletes to analyze the impact on the player satisfaction and performance - a man of 290 people 121 people (41.7%), female 169 people (58.3%) was used as a target sample of the study. Behavioral training and instruction to improve player satisfaction for the leadership of the induction leadership, democratic behavior, social support behavior, reward positive behaviors, and configure the survey on the leaders of the overall leadership behavior. The results showed that leadership is influencing the player satisfaction, appeared to reap good results in performance enhancement, the leader of the social support behavior, influenced by the order of the overall behavior of the leader, the higher the better player satisfaction will reap the results. In addition, the director of leadership training and instruction of the leaders in the impact on the play ability behavior, democratic behavior, social support act, the overall behavior was found to affect the performances. Therefore, if the progress is erected lead dozens of leaders exercise planning and career planning under an agreement rather than a coercive players and make a lot of good results to enhance the player experience and improve performances.

• Journal of Arbitration Studies
• /
• v.28 no.2
• /
• pp.111-135
• /
• 2018

As the disputes in the investment and civil/commercial sectors of China and Taiwan have increased due to active cross-strait economic exchanges, the Chinese government is addressing cross-strait disputes through various dispute resolution methods. In recent years, the Arbitration Center Across the Straits (ACAS) has been established to resolve disputes between cross-strait parties, while ACAS Arbitration Rules have been enacted and enforced. ACAS Arbitration Rules are prepared by referring to the Arbitration Act of China and Taiwan, the relevant provisions and practices of the China International Economic and Trade Arbitration Commission (CIETAC) Arbitration Rules and the cross-strait practical affairs of the China International Economic and Trade Arbitration Commission, and the cross-strait practical affairs giving consideration to the specificity of the cross-strait relationship and the characteristics of economic and trade disputes. Therefore, this paper has compared the features and main contents of the ACAS Arbitration Rules with those of the CIETAC Arbitration Rules. This refers to arbitration proceedings such as form and effect of arbitration agreement, decision of place of arbitration, and organization of arbitral tribunal; the provision of consolidation of multiple contracts and arbitration, and the provision of joinder of arbitration parties, which are implementing the "principle of party autonomy" with streamlining arbitration proceedings and reducing costs; "common, simple, and small sum arbitration proceedings which require shorter arbitration proceedings depending on the size of the arbitration object; and regulations on the "interconnection of mediation and conciliation" which is characteristic of China's arbitration system. Based on the above-mentioned main contents of the ACAS Arbitration Rules in China, there are some implications to be considered in the establishment of the Arbitration Rules of the South-North Commercial Arbitration Commission which will be applied to solve commercial and investment disputes arising from the Inter-Korean Economic Cooperation process, suggesting implications such as the need for the rapid composition and operation of the South-North Commercial Arbitration Commission, requirements for selecting arbitrators, expansion of the object of arbitration, specification of concreteness in deciding the place of arbitration, need to create a variety of arbitration proceedings, and application plan of the International Center for Settlement of Investment Dispute (ICSID) or Third Power Arbitration Agency.

• Journal of Digital Convergence
• /
• v.14 no.12
• /
• pp.645-655
• /
• 2016

The purpose of this study is to analyze the roles and functions of NGO 's International Solidarity in the establishment of' DMZ World Peace Park ', the mechanism of operation, and the policy formation of NGO' s international solidarity. The establishment of the DMZ World Peace Park is a matter that can be achieved as a result of dialogue efforts between the two parties based on the agreement between the DPRK and the ROK government, but should take a more relaxed approach to the process issues in order to achieve such results And should be done in a long-term, step-by-step plan. In the process of realizing this, South Korea's own efforts alone are difficult, and it is necessary to seek various channels of dialogue with the international community so that North Korea can have dialogue negotiations. This will be the role of NGO, It should be noted. As a result, in order to establish 'DMZ World Peace Park', it is necessary to establish concrete road map of DMZ World Peace Park. In the first stage, it is necessary to organize and operate 'DMZ World Peace Park Promotion Committee' under the directorship of the President or Prime Minister, It is necessary to select candidates, to appeal to North Korea and to support the international community, and to participate voluntarily by the private sector. Phase 2 requires final settlement. Phase 3 will require a step-by-step road map, such as rapid construction of the Peace Park, expansion of peaceful use of the DMZ, and expansion of ecology, history and cultural tourism in the DMZ border area.

• The Korean Journal of Air & Space Law and Policy
• /
• v.26 no.1
• /
• pp.93-125
• /
• 2011

The International Civil Aviation Convention (Chicago Convention) has been a backbone of international air transport system whereby air transport between States should be based on bilateral agreements, and in particular, international airfares, which are set up through IATA(International Air Transport Association) rate-fixing machinery could be approved by the governments concerned. International airfares are fares for transporting passenger and freight and their conditions between two or more countries. However, since U.S. pursued th deregulation policy in 1978 whereby routes, capacity and fares could be freely determined by airlines, many States have been following so called open-skies agreements. In many cases, aeronautical and competent authorities have been reviewing whether airlines' commercial activities including air fares could possibly conflict with free competition rules envisaged in relevant laws and regulations. As competition among airlines gets intense, airlines often resort to cooperation with other airlines in the forms such as equity exchange, M&A, code-sharing, fares consultation and resource pooling, mainly with a view to effectively use resources available and to avoid monopoly situation resulting from excessive and destructive competition among players. Whereas bearing in mind that application of competition laws is important to secure consumers' interests by preventing airlines's malpractices such as bargaining exorbitant fares, it is also important to comprehensively consider as many factors as possible, from that unilateral measure by governments may bring about retaliatory measures by the governments affected, to that airlines' cooperative practices may rather increase consumers' benefits by lowering air fares.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.3
• /
• pp.574-579
• /
• 2008

The evaporation heat transfer coefficient of $CO_2$ (R-744) in a horizontal tube was investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator (test section). The test section consists of a smooth, horizontal stainless steel tube of inner diameter of 4.57mm. The experiments were conducted at mass flux of 400 to $900kg/m^2s$, saturation temperature of 5 to $20^{\circ}C$, and heat flux of 10 to $40kW/m^2$. The test results showed the heat transfer of $CO_2$ has a greater effect on nucleate boiling more than convective boiling. Mass flux of $CO_2$ does not affect nucleate boiling too much. In comparison with test results and existing correlations, All of the existing correlations for the heat transfer coefficient underestimated the experimental data. However Jung et al.'s correlation showed a good agreement with the experimental data. Therefore, it is necessary to develope accurate predictions determining the evaporation heat transfer coefficient of $CO_2$ in horizontal tubes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.696-701
• /
• 2016

Multi-stage deep drawing is a widely used industrial manufacturing process, and its applications are gradually expanding to both small products and large metallic products. The USB C-type socket used in smart phones, for example, is manufactured using oval multi-stage deep drawing. The socket is very small and slender and it requires precise manufacturing. The thickness distribution of the final product is guaranteed only if it is uniform throughout the overall process. Therefore, minimizing the height difference between long and short sidewalls after the first operation is important for this goal. An initial blank optimization was performed for an oval-type drawing process based on finite element simulations. The goal was to determine an initial blank geometry that can maintain uniform height and thickness after the first draw operation. The initial blank shape of the sheet metal was optimized, and the results show that it satisfied the conditions of minimal thickness reduction and even thickness distribution. The geometry from the optimized simulation was compared with experimental results, which showed good agreement.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.302-307
• /
• 2016

The technology of multistage deep drawing has been widely applied in the metal forming industry, in order to reduce both the manufacturing cost and time. A battery can used for mobile phone production is a well-known example of multistage deep drawing. It is very difficult to manufacture a battery can, however, because of its large thickness to height aspect ratio. Furthermore, the production of the final parts may result in assembly failure due to springback after multistage deep drawing. In industry, empirical methods such as over bending, corner setting and ironing have been used to reduce springback. In this study, a bottoming approach using the finite element method is proposed as a practical and scientific method of reducing springback. Bottoming induces compression stress in the deformed blank at the final stroke of the punch and, thus, has the effect of reducing springback. Different cases of the bottoming process are studied using the finite element program, DYNAFORM, to determine the optimal die design. The results of the springback simulation after bottoming were found to be in good agreement with the experimental results. In conclusion, the proposed bottoming method is expected to be widely used as a practical method of reducing springback in industry.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.300-309
• /
• 2016

Curved beams are increasingly used in buildings, vehicles, ships, and aircraft, which has resulted in considerable effort towards developing an accurate method for analyzing the dynamic behavior of such structures. The stability behavior of elastic curved beams has been the subject of many investigations. Solutions to the relevant differential equations have traditionally been obtained by the standard finite difference or finite element methods. However, these techniques require a great deal of computer time for a large number of discrete nodes with conditions of complex geometry and loading. One efficient procedure for the solution of partial differential equations is the differential quadrature method (DQM). This method has been applied to many cases to overcome the difficulties of complex algorithms and high storage requirements for complex geometry and loading conditions. Out-of-plane buckling of curved beams with rotatory inertia were analyzed using DQM under uniformly distributed radial loads. Critical loads were calculated for the member with various parameter ratios, boundary conditions, and opening angles. The results were compared with exact results from other methods for available cases. The DQM used only a limited number of grid points and shows very good agreement with the exact results (less than 0.3% error). New results according to diverse variation are also suggested, which show important roles in the buckling behavior of curved beams and can be used for comparisons with other numerical solutions or experimental test data.