• 한국추진공학회지
• /
• 제10권4호
• /
• pp.93-99
• /
• 2006

막냉각량과 작동점의 변화에 따른 축소형 칼로리미터의 열유속 특성을 실험과 해석을 통해 알아보았다. 칼로리미터의 실린더 부분은 8개의 채널로, 노즐부는 11개의 채널로 구성되어 있다. 설계점 연소시험 시 막냉각량이 전체 연료유량의 10.5%일 때 노즐목에서의 열유속은 막냉각이 없을 때보다 약30% 감소하였다. 또한 막냉각이 없을 경우, 고압-고혼합비 조건 연소 시험 시 노즐목에서의 열유속이 설계점 시험 시보다 약 31% 증가함을 보였다.

• 대한설비공학회지:설비저널
• /
• 제17권6호
• /
• pp.696-707
• /
• 1988

This study simulates a typical solar system using the transient simulation program TRNSYS, and calculates the maximum cooling load of the model room of $50m^2$. In this study, energy rate control method is used in calculating a maximum cooling load. On the ground of the maximum cooling load of the model room, the variables that have an effect on the solar collection performance of the solar system are made a selection. Also in this study the trend of the solar collection performance is shown as the variables change. The results show that the variables which have an effect on the collection performance are collector area, collector mass flow rate, collector slope and the volume of storage tank, and the optimal value of Ac/Vt is not constant but varies as the collector area and the collector mass flow rate. Also the results show that for cooling system the optimal value of the collector slope is latitude minus $15^{\circ}$ during the seasonal operations, and twenty percent of the maximum cooling load is saved with the aid of the solar energy.

• 열처리공학회지
• /
• 제4권3호
• /
• pp.39-46
• /
• 1991

The effects of austenitizing temperatures and times and cooling rate on the characteristics of continuous air cooling have been investigated for 0.3%C-Mn steels microalloyed with vanadium. Transformation start temperatures have been found to be measured from temperature-time curve directly obtained with continuous air cooling and to decrease with increasing austenitizing temperature, cooling rate and Mn contents. The coarsening behavior of austenite grain size has been measured to abnormally grow at $1050^{\circ}C$ and rapidly grow at $1200^{\circ}C$. It has been found that the volume fraction of pearlite was linealy proportional to the reciprocal square root of austenite grain size. The hardness has been measured to increase with increasing cooling rate up to $250^{\circ}C/min.$ and to remain relatively unchanged in the range of $250{\sim}400^{\circ}C/min.$ showing that hardness valves for steel with a higher Mn content increase more than those for steel with a lower Mn content. The impact property has been found to decrease with increasing of austenite grain size but does not linealy change with the reciprocal square root of austenite grain size.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.77-88
• /
• 1997

The heat rejection to coolant is a dominant factor for building vehicle cooling system such as radiator and cooling fan. Since the vehicle cooling system also has effects on fuel consumption and noise, the study of heat rejection to coolant has been emphasized. However, the study on heat rejection to coolant has been mainly focused on the field that related to the characteristics of combustion and localized heat loss. It is no much of use in design for the entire cooling system because it is focused on such a specific point. In this work, the heat rejection rate to coolant for four different engines are obtained to derive a simple heat transfer empirical formula that can be applied to the engine cooling system design, and it is compared with the other studies. Also, to observe effects of engine operation factors and heat transfer factors on coolant, we measured the metal temperature and the heat rejection rate. The heat rejection to coolant does not depend significantly upon the coolant flowrate, but mainly upon the amount of air fuel mixture and the air fuel ratio as long as the composition of coolant does not change. The reduction of heat rejection to coolant did not effectively improve the fuel consumption, but was mostly converted to raise the exhaust gas temperature and the oil temperature.

• 설비공학논문집
• /
• 제19권12호
• /
• pp.850-856
• /
• 2007

In a supercooled or capsule type ice storage system, aqueous solution (or water) may have trouble with non-uniform dissolution though the system contributes to the simplicity of system and ecological improvement. The non-uniform dissolution increases the instability of the system because it may cause an ice blockage in pipe or cooling part. In order to observe the supercooled state, a cooling experiment was performed with pressurization to an ethylene glycol(EG) 3 mass% solution in stationary state. Also, the effect of the pressurization from 101 to 505 kPa to the dissolution of supercooled aqueous solution was measured with the dissolution time of the supercooled aqueous solution at a fixed cooling rate of brine. At results, the dissolution of supercooled point decreased as the pressure of the aqueous solution in the vessel increased. Moreover, the dissolution point increased as the heat flux for cooling increased.

• 설비공학논문집
• /
• 제23권8호
• /
• pp.562-570
• /
• 2011

In this research, an experimental study is performed to investigate the effects of system operating variables on the cooling and heating characteristics of heat pump system using geothermal heat source and carbon dioxide as a refrigerant. System variables analyzed include compressor frequency, electronic expansion valve opening, refrigerant charge, secondary fluid temperature and flow rate. Results show that optimum refrigerant charge and electronic expansion valve opening position exist at the maximum point of COP curve, and both cooling and heating capacity increase but COPs decrease with the increase of compressor frequency. The change of a secondary fluid temperature leads to variation of overheat area and enthalpy difference in the evaporator and gas cooler. which again results in considerable variations of cooling and heating capacity and COP. In the case of effects of secondary water fluid flow rate, both cooling capacity and COP increase with the increase of secondary flow in evaporator or gas cooler, whereas heating capacity and COP decrease with the increase of flow rate in gas cooler.

• 설비공학논문집
• /
• 제19권9호
• /
• pp.647-653
• /
• 2007

In dynamic ice storage system(DISS), ice slurry is formed not only from solution freezing by mechanical removing parts but also supercooled solution. However, in order to perform continuous ice formation in the system without mechanical moving parts, supercooled aqueous solution should be formed stable through cooling heat exchanger and be dissolved uniformly in storage tank. In previous study, the time of ice slurry increased as the pressure of the cooling heat exchanger(PHX) increased. In this study, a cooling experiment of an ethylene glycol 7mass% solution was performed with various inlet temperature of the PHX, which has constant brine inlet temperature of $-7^{\circ}C$. The temperature in the storage tank maintained to freezing point of the solution. At results, the time of ice slurry formation increased as the supercooling degree decreased and the cooling rate increased.

• 대한건축학회논문집:구조계
• /
• 제35권11호
• /
• pp.181-188
• /
• 2019

The purpose of this study is to evaluate the cooling energy saving effects of CRAH supply air temperature(SAT) and design flow rate changes when applying air-side economizer in the data center. MLC(Mechanical Load Component), which is cooling performance indicator of data center, was used to assess the effectiveness of cooling energy savings. It was computed with energy simulation (DesignBuilder) to evaluate the cooling energy performance of 8 different alternatives in a data center. The MLC was 0.31~0.32 regardless of CRAH supply temperature without air-side economizer, and 0.15 to 0.19 value with air-side economizer. That is, cooling energy can be reduced by approximately 40~55% when applying economizer. As the CRAH SAT and design flow rate changed, the MLC values were 0.16 to 0.18 and 0.15 to 0.19, respectively.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.189-193
• /
• 2005

로켓엔진에서 선형 연소 안정한계에 미치는 유한화학반응의 열적 효과와 막냉각 효과를 조사하였다. 안정한계를 평가하기위해 3차원 연소실에서 유한화학반응을 채택한 반응 유동장 계산으로부터 구한 유동변수들을 사용하였다. 주요 유동변수들의 값은 유한화학반응 모델의 채택으로 인해 상당히 달라졌으며 결과적으로 안정한계도 수정되었다. 유한화학반응은 열적 관점에서 안정성 향상에 기여함을 알았다. 또한, 막냉각을 한 경우, 안정성 경향이 향상됨을 알 수 있었다.

• 설비공학논문집
• /
• 제23권11호
• /
• pp.747-753
• /
• 2011

The purpose of this study was to quantify the impact of the ventilation rate on heating and cooling energy consumption in a detached house. For it, a series of simulations for the application of the diverse ventilation rate (ACH) were computationally conducted for a prototypical detached residential building in the cold climate (Detroit, Michigan) and hot/humid climate (Miami, Florida) of USA. Analysis revealed that ventilation is a significant heat losing source in the cold climate; thus, the higher ventilation rate significantly increases the heating energy consumption and energy cost in the cold climate; while the impact on energy increase for heating and cooling energy consumption is similar in hot/humid climate with less significancy compared to cold climate. The research outcome of this study could be a fundamental data for determining the optimal ventilation rate in terms of indoor air quality, but also building energy performance well.