• Journal of the Korean Society of Safety
• /
• v.8 no.4
• /
• pp.120-126
• /
• 1993

This work was carried out to investigate the effects of solid mass flow rate, mean particle diameter and mesh number of screen packing material on minimum carrying velocity, which defined as the superficial gas velocity of the upper limit of chocking phenomenon. Vertical pneumatic conveying was studied on a 4.6cm 1. D. pipe, 180cm in length. Experiments were performed in both the empty and the screen-packed pipe. It was also examined the effect of superficial gas velocity, solid mass flow, mean particle diameter, and mesh number of packing material on pressure drop. Minimum carrying velocity in screen packed-pipe was lower than that in an empty pipe. besides minimum carrying velocity was decreased with increase in mesh number of screen packing material. The pressure drop In vortical packed-pipe was Increased with superficial gas velocity, mean particle diameter, and mesh number of screen packing material.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.2
• /
• pp.145-154
• /
• 2016

In this paper, a pneumatic device for the deployment performance verification of canards deployed by inertia has been designed and the performance of the pneumatic device has been proven through analysis and tests. The pneumatic conveying process, orifice opening process and piston movement process of the pneumatic device were investigated by using numerical methods. The orifice diameter, pressure in a pressure tank and type of gas were regarded as the main design parameters of the pneumatic device. The error rate between analysis and test results under the same conditions was within 4 %. The accuracy of numerical methods used in this study were validated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.1 s.244
• /
• pp.32-41
• /
• 2006

We analyzed the non-Newtonian and non-isothermal flow in the melt conveying zone in co-rotating and counter-rotating screw extruder system with the commercial code, STAR-CD, and compared the mixing performance with respect to screw speed and rotating direction. The viscosity of fluid was described by power-law model. The dynamics of mixing was studied numerically by tracking the motion of particles in a twin screw extruder system. The extent of mixing was characterized in terms of the residence time distribution and average strain. The results showed that high screw speed decreases the residence time but increases the shear rate. Therefore higher screw speed increases the strain and has better mixing performance. Counter-rotating screw extruder system and co-rotating screw extruder has the similar shear rate with the same screw speed in spite of different rotating direction. However, the counter-rotating screw has good mixing performance, which is resulted from longer residence time than that of co-rotating screw extruder.

• Korea-Australia Rheology Journal
• /
• v.18 no.3
• /
• pp.153-160
• /
• 2006

We analyzed the non-Newtonian and non-isothermal flow with Carreau-Yasuda viscosity model in co-rotating and counter-rotating twin screw extruder systems. The mixing performances with respect to the screw speed, the screw pitch, and the rotating direction have been investigated. The dynamics of mixing was studied numerically by tracking the motions of particles. The extent of mixing was characterized in terms of the deformation rate, the residence time distribution, and the average strain. The results showed that the high screw speed decreases the residence time but increases the deformation rate. Small screw pitch increases the residence time. It is concluded that the high screw speed increases the dispersive mixing performance, while the small screw pitch increases the distributive mixing performance. Co-rotating screw extruder has the better conveying performance and the distributive mixing performance than counter-rotating screw extruder with the same screw speed and pitch. Co-rotating screw extruder developed faster transport velocity and it is advantageous the flow characteristics to the mixing that transfers polymer melt from one barrel to the other barrel.

• Journal of Drive and Control
• /
• v.20 no.3
• /
• pp.35-41
• /
• 2023

Radish and Chinese cabbage are the most produced and consumed vegetables in Korea. The mechanization of harvesting operations is necessary to minimize the need for manual labor. This study to develop and evaluate the performance of a multi-purpose driving platform that can apply modular Radish and Chinese cabbage harvesting devices. The multi-purpose driving platform consisted of driving, device control, engine, hydraulic, harvesting, conveying, and loading part. Radish and Chinese cabbage harvesting conducted using the multi-purpose driving platform each harvesting module. The performance of the multi-purpose driving platform was evaluated the field efficiency and loss rate. The total Radish harvesting operation time 34.3 min., including 28.8 min., of harvesting time, 1.9 min., of turning time, and 3.6 min., of replacement time of bulk bag. During Radish harvesting, the field efficiency and average loss rate of the multi-purpose driving platform were 2.0 hr/10a and 3.1 %. Chinese cabbage harvesting operation 49.3 min., including 26.6 min., of harvesting time, 4.6 min., of turning time, and 18.1 min., of replacement time of bulk bag. During Chinese cabbage harvesting, the field efficiency and average loss rate of the multi-purpose driving platform 2.1 hr/10a and 0.1 %. Performance evaluation of the multi-purpose driving platform that harvesting work was possible by installing Radish and Chinese cabbage harvest modules. Performance analysis through harvest performance evaluation in various Radish and Chinese cabbage cultivation environments is necessary.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.131-140
• /
• 2001

This study was conducted to develop a garlic separator which could to reduce the labor in preparation of seeding. After consideration of the design criteria of a garlic separator such as no additional conveying device, simple construction and operation, enhancement of separating efficiency, reduction of damage, degree a rotating corn type garlic separator was designed. The effects of design parameters such as height and angle of the inner and outer corns, rotating speed of inner corn on the separating performance of the prototype were estimated. In performance was compared with manual work. The results are summarized as follows. 1. Garlic bulbs were separated by a spiral movement in the gap between inner rotating corn and outer fixed corn. At constant feed rate of garlic bulbs, the capacity of garlic separation increased with increase of rotating speed of inner corn. Especially, the capacity was very high at the rotating speeds of 300 and 400rpm. 2. The damage degree of separated garlics increased with rotating speed of corn within 10%. Above 300rpm, separability of Uisung garlic was about 100% and incomplete separation of Namdo garlic was within 2%. 3. The capacity of prototype garlic separator developed in this study was 30 times as large as that of human being.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.4 no.6
• /
• pp.989-1005
• /
• 2010

Cooperative diversity is a technique with which a virtual multiple antenna array is established among the single antenna users of the wireless network to realize space diversity. Signal space diversity (SSD) is a bandwidth-efficient diversity technique, which uses constellation rotation and interleaving techniques to achieve diversity gain. A new cooperative diversity scheme with rotated constellations (RCCD) is proposed in this paper. In this scheme, data are modulated by using a rotated constellation, and the source and the relays transmit different components of the modulated symbols. Since any one of the components contains full information of the symbols, the destination can obtain multiple signals conveying the same information from different users. In this way, space diversity is achieved. The RCCD scheme inherits the advantage of SSD - being bandwidth-efficient but without the delay problem of SSD brought by interleaving. The symbol error rate of the RCCD scheme is analyzed and simulated. The analysis and simulation results show that the RCCD scheme can achieve full diversity order of two when the inter-user channel is good enough, and, with the same bandwidth efficiency, has a better performance than amplify-and-forward and detect-and-forward methods.

• Journal of Bio-Environment Control
• /
• v.14 no.1
• /
• pp.7-14
• /
• 2005

This study was conducted to develop a chain conveyor-type, row-spacing system for a plant factory. The developed system was evaluated for its practical use in growing plants. Results are intended to provide technical suggestions on the row spacing for hydroponically grown vegetables in a plant factory. The designed row-spacing system for a plant factory could be adjusted by four stages with a conveying speed range of $5.3\~15.8cm{\cdot}s^{-1}$ and with a row-space range of 10-25cm. The torque of driving shaft was measured with a torque range of 11.7-33.3 N$\cdot$m according as a trough weight changes with a range of $17\~935$ N. A measured value was $5.9\~9.8\;N{\cdot}m$ lower than a theoretical value. Travel reduction rate was shown up $1.6\~1.9\%$. The conveying time of trough was shown up 2.24 seconds in case that the designed value was 2.26 seconds. The system was evaluated to be functioning effectively according to the initial design factors in the test.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.342-350
• /
• 2009

Currently TMR feed produced in commercial plant is one of the major source to feed cattle for both beef and dairy farm. However, because of lack of cutting and mixing system for utilizing domestic produced firmly baled round roughage in commercial TMR plant, these commercial TMR feed can not satisfy to farmers both in quality and price points of view. In order to solve these problems, a farm group size TMR plant model was developed in this study. The model plant was consist of round bale receiving and cutting system, pneumatic conveying system for transfer the roughage which was cut at the cutter to TMR mixer through pneumatic conveyor, TMR mixer enable to soften the stiff rice strew and to mix with other ingredients, finished feed bin which can be transfer to either packing system or individual farm, packing system by tycon bag which contains 400 kg unit and bulk unloading system to individual farmer. Also, a simulation model ARENA was applied to the model system in order to evaluate and check the production rate in each unit process and operation rate of total system and to find out if there are any clogged unit system obstructing the smooth flow of the total process flow. Processing cycle for produce one batch of the model plant was less than 30 minutes. Thus, it will take less than four hours for producing 16 tons per day equivalent to 1,000 beef cattle's daily feed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2430-2435
• /
• 2015

In order to achieve high flexibility in manufacture, analysis of chip's shape is one of the most important problems. This paper describes the change of machining characteristics in workpiece materials depending on turning clearance angle. The experiments start from choosing three workpiece materials that are SM45C(machine structural carbon steel), STS303(stainless steel), SCM415 (chrome-molybdenum steel). Then, the experiments show specifically how features of selected materials changed when they were processed with diverse machining depths and with feed rate starting from fixed rotational speed. Especially, the experiments were also analyzed in chip's shape and wear of insert tip. In conclusion, these experiments show that chip's shape was changed by quality of the materials, depth of cut, and conveying speed. When machining feedrate and machining depth were 0.10mm/rev and 0.3mm respectively, workpiece materials showed the best shapes, not categorizing quality of the materials and machining characteristics.