• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.1-8
• /
• 2003

When solving the problems of electric power quality the converters with high Power factor are useful for the DC arc furnace power supply. In this paper, resonant converters of 50(60) Hz AC to DC arc described, where in each period of network voltage the capacitor and inductor of an oscillatory circuit are switched from series into parallel and vice versa parametrically. The duration of series and parallel connection and also the transformation ratio are dependent on load. Parallel oscillatory circuit restricts the short circuit current. These converters have high power factor from no-load to short-circuit and fit very well to supply are furnaces.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.149-152
• /
• 2006

In this paper, we researched and compared the properties of steel slag(is divided with electric arc furnace slag and converter slag) as concrete aggregate by measuring physical and chemical characteristics of it. The steel slag mainly contains SiO2 and CaO as the chemical composition. The reaction with water and a little of free CaO in the slag causes slag's volume to expanse. Therefore, we used several aging methods in order to decrease the characteristics of slag volume expansion. The physical properties of steel slag aggregate is researched and then the strength of concrete with the steel slag aggregate is measured.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.542-546
• /
• 2001

Converter slag has some compositional similarities to portland cement. But it has no hydration properties due to it's quite high concentrations of FeO(20-35%), MnO(4-6.5%). So it is needed to reduce the concentrations of iron and manganese of converter slag to use as cement additives by enhancing it's hydration properties. In this study, converter slag was modified it's composition by mixing of silica, alumina and quenched BF slag and reduced in induction furnace and quenched in running water. The hydraulic properties and structures of modified and quenched converter slag are significantly changed depend on the amount and kinds of additives. The addition of alumina up to 10% and BFQ slag up to 20% by weight on converter slag was effective to enhance the hydraulic properties of modified and quenched slag. The addition of reduced and quenched converter slag up to 20% by weight in replacement of portland cement in mixing of concrete mortar were shown higher compressive strength than 100% cement concrete mortar.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.318-321
• /
• 2003

Steel slag is produced during steel making process. Compared with the blast furnace slag, converter slag has the expansibility due to the reaction with water and free CaO. Therefore it is specified in Standard Specification for Concrete in Korea that steel slag aggregate must not be used in concrete. In this study, atomized steel slag aggregate is conducted from converter slag by the atomizing method. Atomized steel slag and conventional converter slag are same in its composite by nature in the converter but compounds of the composite become different because of different method of slag treatment. Especially atomized steel slag aggregate overcomes expansibility that is the weak point for usage. It is researched whether it has the possibility, suitability for fine aggregate in concrete. Slump and air content are measured in fresh concrete, compressive and bending strength in hardened concrete. These is compared with control concrete with washed sand.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.202-209
• /
• 2001

As a part of stringent emission regulations, OBD on a converter is requested by EU and CARB. It demands that MIL is light-on to inform the failure to the driver when the converter is failed in its function. Usually dual oxygen sensor method is used for converter OBD. For this, detail methods, like amplitude ratio, time delay and frequency ratio methods are adapted for vehicle application. Actually, the cars produced later than MY94 for US market are using one of these methods. In this study, OSCs of converters are investigated with an absolute measuring method. The converters are aged with a furnace aging, an engine bench aging and vehicle aging method to represent various aging condition in field applications. An OBD index that is used for TLEVs regulation is also investigated to find a relation between two parameters. The relations of these parameters with THC emission on vehicle are evaluated.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.10a
• /
• pp.117-118
• /
• 2016

This paper evalutes properties of extruding cement panel using Ca-extracted convert slag and air-cooled blast furnace slag. Flexural strength of extruding cement panel has measured in air dry and autoclave curing as basic study for use as silicious source. As a result, when Ca-extracted converter slag replaces 25% in autoclave curing, flexural strength measures 13.1MPa better than panel control mix. In result of using air-cooled blast furnace slag, Ca-extracted air-cooled blast furnace slag dose not show increase of flexural strength.

• International Journal of Automotive Technology
• /
• v.3 no.1
• /
• pp.33-40
• /
• 2002

Increasingly stringent emission regulations of EU and CARB (California Air resource Board) require mandatory OBD (On Board Diagnostics) far the catalytic converters of a vehicle. It demands that MIL(Malfunction Indication Light) should be tuned on to inform the driver of catalytic converter failures. Currently dual oxygen sensor method Is widely used for the converter OBD. However, since it works only alter converter light-off, it has a serious limitation when applied to TLEV or more stringent emission regulations where more than 85% of total emission is coming out before converter light-off. In addition, a recent development in catalyst material. coating technology and additive catalysts leads to a much improved OSC (Oxygen Storage Capacity) after converter light-off, current methods are very difficult to determine levels of converter aging. Therefore, it is desired to develop an OSC detecting method before converter light-off to diagnose converter failures with higher reliability. In this study, OSCs of converters are measured by an absolute measuring method and a dynamic measuring method, and some of fundamental ideas are suggested about converter OBD before converter light-off. The converters are aged with two different aging methods; those are a furnace aging and an engine bench aging: to represent aging conditions in actual field applications. Dual oxygen sensor method at the lower temperature than light-off is also studied at a model gas bench with the converters. It is fecund that there is a certain point in temperature lower than light-off where difference due to aging level becomes maximum, thus a proper dynamic method to effectively monitor catalytic converters could be implemented fur the range lower than light-off temperatures. With this result, the aging level of converters is examined at an engine bench.

• Journal of the Korean Society of Safety
• /
• v.18 no.2
• /
• pp.6-15
• /
• 2003

A method is presented for diagnosing the converter bearings by using acoustic emission. The flaking mechanism causing the large-scale bearing for furnace to flaw is investigated and a possibility of defect is verified by Finite Element method. he diagnosis logic is proposed fir detecting the flaw of a non-continuous rotating machine. It is proved that the acoustic emission energy can be used as a representative parameter for an acoustic event. Applying the method to the tilting bearings for steel mill in operation, the effectiveness of this logic is evaluated. It is shown that AE signal is generated only when the bearing is tilting, and the trend analysis can be focused upon this process.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.1
• /
• pp.35-40
• /
• 2011

Magnesia-carbon brick is used to refractory material in Converter and/or Ladle furnace for molten steel manufacturing. The rapid growth of steel making industry, molten steel industry is increased. Therefore, growth of molten steel industry lead to make waste magnesia-carbon brick by repair of Converter and/or Ladle furnace. These waste magnesia-carbon brick is abandoned all. Besides, as it is loosely composed of silt and clay including sand falling according to the type of gangue, rainwater inflows and outflows relatively easily, but silt or clay particles absorb water for a long period, weakening ground. This study tried to show that when colluvial soil is solidified using waste magnesia-carbon brick powder as a way to solidify strengthen the rigidity of colluvial soil.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.233-236
• /
• 1999

In this paper, we carried out fundamental experiments to use the steel manufacturing slag as a concrete aggregate. Generally there are two types of slag, the blast-furnace slag and the steel manufacturing slag. The latter is classified by the difference of manufacturing method of steel into the convertor slag and the electric-furnace slag. The steel manufacturing slag mainly contains SiO2 and CaO as the chmical composition. The reaction with water and a little of free CaO in the steel manufacturing slag makes the expansion of volume change. Therefore, we primarily investigated physical properties, expansion mechanism, pH value, aging effects and aging methods in the steel manufacturing slag. Then compressive strength of concrete with steel slag aggregate is measured.