• 항공우주시스템공학회지
• /
• 제9권1호
• /
• pp.12-18
• /
• 2015

The inter-conversion between different control laws in flight has a lot of risk. The SWM(Switching Mechanism) including logic and stand-by mode is designed to analyze the transient response of aircraft during inter-conversion between different control laws, based on the in-house software for non-real-time and real-time simulation. The SWM applies the fader logic of TFS(Transient Free Switch) to minimize the transient response of an aircraft during the inter-conversion, and applies the reset '0' type of the stand-by mode to prevent surface saturation due to integrator effect in the disengaged flight control law. The transition time is also important to minimize the objectionable transient response in the inter-conversion, as well as the transition control law design. This paper addresses the results of non-real-time simulation for the characteristics of transient response to different transition time to select the adequate transient time, and the real-time pilot evaluation, using SSWM(Software Switching Mechanism) and HSWM(Hardware Switching Mechanism), which is met for Level 1 flying qualities and assures safety of flight.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권10호
• /
• pp.464-470
• /
• 2006

In this paper, we develop a descriptor based on binary ECG conversion system that supports the conversion of a binary ECG format into XML-based HL7 aECG for the interoperability of ECG. HL7 aECG is a XML based standard for interoperability of ECG waveform. For the conversion of variety of ECG formats, we propose a binary ECG description mechanism. In order to describe binary ECG more efficiently, we develop a XML-based Binary ECG Description (BED) Language. One of the powerful features of using the XML-based ECG Description mechanism is that ECG data can read from various formats without the modification of source code of conversion system, and consequently it reduces conversion system maintenance costs.

• 전기학회논문지
• /
• 제56권6호
• /
• pp.1151-1156
• /
• 2007

In this paper, we develop a new conversion method for implementing binary ECG(Electrocardiogram) conversion scheme to improve our previous research works that supported the conversion of binary ECG files into HL7 aECG for enhancing interoperability of ECG data. HL7 aECG is a XML-based standard for interoperability of ECG waveform. To improve the performance of ECG data conversion, we utilize a compilation-based ECG conversion method on binary ECG files. Our new method supports both flexibility of BED-based ECG conversion mechanism and the performance of direct conversion mechanism.

• Korean Chemical Engineering Research
• /
• 제44권4호
• /
• pp.329-339
• /
• 2006

원유가 급등으로 메탄올에서 저급 올레핀을 제조하는 공정에 대한 관심이 높아지고 있다. 제올라이트와 SAPO 분자체 촉매에서 메탄올의 탄화수소로 전환 반응을 저급 올레핀 생성 단계에 중점을 두고 고찰하였다. 구조가 명확한 중간체를 근거로 하는 직접(direct) 반응기구와 구조가 애매한 탄화수소 뭉치를 활성점으로 보는 탄화수소 활성체(hydrocarbonpool) 반응기구의 합리성을, 메탄올 전환 반응의 유도기간, 생성물의 선택성, 활성 저하 등과 연계지어 비교하였다. 탄화수소 활성체의 구조 규명과 메탄올 전환 반응에서 촉매 활성점으로서 기능에 대한 1999년 이후 연구 결과를 검토하였으며, 메탄올에서 저급 올레핀을 생산하는 공정에 대한 전망도 기술하였다.

• 한국지능시스템학회논문지
• /
• 제17권1호
• /
• pp.123-129
• /
• 2007

On the Semantic Web, the content of the documents must be explicitly represented through metadata in order to enable contents-based inference. In this study, we propose a mechanism to convert the Conceptual Graph (CG) into Resource Description Framework (RDF). Quite a large number or representation languages for representing knowledge on the Web have been established over the last decade. Most of these researches are focused on design of independent knowledge description. On the Semantic Web, however, a knowledge conversion mechanism will be needed to exchange the knowledge used in independent devices. In this study, the CG could give an entire conceptual view of knowledge and RDF can represent that knowledge on the Semantic Web. Then the CG-based object oriented PROLOG could support the natural inference based on that knowledge. Therefore, our proposed knowledge conversion mechanism will be used in the designing of Semantic Web-based knowledge representation and inference systems.

• Current Optics and Photonics
• /
• 제2권5호
• /
• pp.395-399
• /
• 2018

This article investigates the mechanism of electronic signal phase noise degradation induced by laser phase noise in optical links comprising optical resonators. Through theoretical derivation, we find that the phase noise of the output electronic signal has the same spectral shape of optical intensity noise as the output of the optical resonator. We propose that the optical resonator transfers laser phase noise to light intensity fluctuation and then the intensity fluctuation is converted to electric phase noise through AM-PM conversion mechanism in the photodiode. An optical link comprising a Fabry-Perot resonator was constructed to verify the proposed mechanism. The experimental results agree with our theoretical prediction verifying that the supposition is correct.

• Bulletin of the Korean Chemical Society
• /
• 제31권9호
• /
• pp.2447-2448
• /
• 2010

• Elastomers and Composites
• /
• 제14권4호
• /
• pp.231-252
• /
• 1979

Polymerization of 2-pyrrolidone was carried out through anionic mechanism using $SO_2/KOH$ as catalyst. The effects of KOH concentration, $SO_2/KOH$ mole ratio and temperature on polymerization were investigated. The conversion and viscosity of polymers were measured at various polymerization conditions. It was observed that as the concentration of KOH was increased, equilibrium conversion was also increased. It was, however, found that after the concentration of KOH was reached above 8 mole percent, the equilibrium conversion was decreased. The highest rate of polymerization and maximum conversion were obtained when $SO_2/KOH$ mole ratio was around 0.5. It was also found that the rate of polymerization and the equilibrium conversion were higher at $50^{\circ}C$. than at $30^{\circ}C$. but the viscosity of polymer solution at $50^{\circ}C$. was not so high as expected. The rate constant, $K_p$ of polymerization, was determined by least square method: the value of $K_p$ was observed as 16 liter/mole hour at $50^{\circ}C$. and 2.6 liter/mole hour at $30^{\circ}C$., respectively. The mechanism of polymerization was also discussed.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.17-17
• /
• 2012

Magnesium alloys exhibit many attractive properties such as low density, high strength/weight ratio, high thermal conductivity, very good electromagnetic features and good recyclability. However, most commercial magnesium alloys require protective coatings because of their poor corrosion resistance. Attempts have been made to improve the corrosion resistance of the Mg alloys by surface treatments, such as chemical conversion coatings, anodizing, plating and metal coatings, are commonly applied to magnesium alloys in order to increase the corrosion resistance. Among them, chemical conversion coatings are regarded as one of the most effective and cheapest ways to prevent corrosion resistance. In this study, zinc phosphate conversion coatings on various Mg alloys have been developed by selecting proper phosphating bath composition and concentration and by optimizing phosphating time, temperature. Morphology, coatings composition, corrosion resistance, adhesion and its formation and growth mechanism of the zinc phosphate conversion coatings were studied. Results have shown some attractive properties such as simplicity in operation, significantly increased corrosion protective property. However, adhesions between coatings and substrate and also between coatings and paint are still not satisfied. Resolving the problems and understanding the mechanism of phosphating process are targets of our study.

• 한국경영정보학회:학술대회논문집
• /
• 한국경영정보학회 2008년도 춘계학술대회
• /
• pp.428-433
• /
• 2008

The online advertising industry's business model undertakes the change from CPM (cost-per-mille)-based to CPC (cost-per-click)-based. However, due to the problem of 'Click Fraud', CPA (cost-per-action) has been regarded as a new step. For CPA, publishers need to get information after a user clicks an advertisement. Therefore, in CPA, the key is to get Conversion Action Data (CAD). This paper introduces two existing mechanisms for getting CAD, compare their characteristics, and analyze their limitations. Then the two new mechanisms are introduced and their requirements and feasibility are analyzed. Lastly, we compare the existing two and the new two mechanisms, and point out each mechanism's business possibility, value and Application Area. This paper will help publishers choose the most appropriate mechanism on the basis of their situation.