• Journal of Environmental Science International
• /
• v.29 no.1
• /
• pp.95-108
• /
• 2020

Silver nanoparticles were loaded onto g-C₃N₄ (CN) with a nanoroll-type morphology (Ag/CN) synthesized using a co-polymerization method for highly selective conversion of toxic nitrobenzene to industrially-valuable aminobenzene. Scanning electron microscopy and high-resolution transmission electron microscopy (HRTEM) images of Ag/CN revealed the generation of the nanoroll-type morphology of CN. Additionally, HRTEM analysis provided direct evidence of the generation of a Schottky barrier between Ag and CN in the Ag/CN nanohybrid. Photoluminescence analysis and photocurrent measurements suggested that the introduction of Ag into CN could minimize charge recombination rates, enhancing the mobility of electrons and holes to the surface of the photocatalyst. Compared to pristine CN, Ag/CN displayed much higher ability in the photocatalytic reduction of nitrobenzene to aminobenzene, underscoring the importance of Ag deposition on CN. The enhanced photocatalytic performance and photocurrent generation were primarily ascribed to the Schottky junction formed at the Ag/CN interface, greater visible-light absorption efficiency, and improved charge separation associated with the nanoroll morphology of CN. Ag would act as an electron sink/trapping center, enhancing the charge separation, and also serve as a good co-catalyst. Overall, the synergistic effects of these features of Ag/CN improved the photocatalytic conversion of nitrobenzene to aminobenzene.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.10
• /
• pp.1388-1394
• /
• 2018

In this paper, the improvement of the control response by using the error compensator to improve the stability of the control in the power conversion system is verified. Typically a closed loop control method is used to improve the control response characteristics in a traditional power conversion system and this is accomplished by generating a PWM waveform. In this paper, the newly constructed Type3 compensator to overcome the existing such as PI controller or Type2 compensator has been developed to improve the control stability of these closed loop control systems and the effectiveness of the use of error compensation devices was verified by presenting technique to improve stability and select its parameters by expanding the range of phase gains. Stability improvements are shown by the extension of the phase gain range and parameter selection techniques and the effects of using the error compensation device are verified accordingly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.223-227
• /
• 2003

In this study, ultrasonic rotary motors using a bolted langevin type ultrasonic vibrator were designed and fabricated. The stator vibrator has a longitudinal transducer section composed of two metal blocks and two piezoelectric ceramic elements (thickness-polarized) and a mode conversion metal block section called a torsion coupler. And, three kinds of motors were studied by finite element analysis and experiments. So, as material of torsion coupler which generate mode conversion of vibration copper, brass, and phosphor bronze were used. As a result, speed and torque were changed in proportion to the electrical input Voltage, but it was saturated in high voltage. And bad efficiency which was different from a expectation was measured in this motors. So, various problems should be improved for practical use. Finally, The motor which has 1 [cm] diameter was fabricated to present a possibility of miniaturization of this type motors.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.195-203
• /
• 2011

This paper is to analysis technical characteristics occured in the eletric train power conversion device passing automatic changover system in neutral section of electric railway. Power conversion devices in electric train are classified according to the current type and voltage type. The results of this study is used to ensure the stability of electric train in neutral section of electric railway.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1880-1883
• /
• 1997

An Parallax-Barrier type autostereoscopic display system is implemented to overcome the handicap of current glass-typed stereo imaging system which gives operators unnatural feeling and reluctance. This system is composed of image mixing part of two input images, A/D transformation part, scan conversion part to eliminate the rainbow interference phenomenon, and pin-hole type barrier lens. For the fine display the accurate slit width of barrier is calculated in consideration of retina size, and the samsung 10.4" TFT-LCO was used as flat display monitor.itor.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.33 no.6
• /
• pp.203-211
• /
• 1984

MOS silicon solar cells have been developed using the fixed (interface) charge inherent to thermally oxidized silicon to induce an n-type inversion layer in 1-10 ohm-cm p-type silicon. Higher collection efficiencies are predicted than for diffused junction cells. Without special precautions a conversion efficiency of 14.2% is obtained. A MOS silicon solar cell is described in which an inversion layer forms the active area which is then contacted by means of a MOS grid. The highest efficiency is obtained when the resistivity of the substrate is high.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.3
• /
• pp.123-127
• /
• 2004

Mode conversion type ultrasonic rotary motor using bolt tightened Langevin type vibrator was studied. Driving frequency of the motor, displacements and elliptical trajectories at tip of the coupler were simulated by finite element analysis program (ANSYS). Speed and torque of the fabricated motor were measured as functions of input voltage and load. As results, from FEA the driving frequency of 40.8[kHz] and useful elliptical trajectories were found. Fabricated motor rotated clockwise at frequency of 38.2[kHz]. Speed and torque of the motor were increased when the input voltage was increased. Maximum speed, torque and efficiency were 75[rpm], 0.14[Nm] and 6.28[％], respectively.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.55-60
• /
• 2009

The purpose of the research is to develop the high performance solar chemical reactor for producing hydrogen using steam reforming reaction of methane. A specific shape chemical reactor is suggested: spiral type reactor. The reactor is installed on the dish-type solar thermal system of Inha University. The temperatures, $CH_4$ conversion rates are measured. At specific condition, $CH_4$ conversion rates of the spiral type reactor are about 92%. The spiral type reactor gives reasonably good performance without any problems caused by highly concentrated solar radiation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.268-268
• /
• 2010

단일벽 탄소 나노튜브(SWCNT)는 그 뛰어난 전기적, 물리적 특성 때문에 반도체 공정에 있어서 중요한 p-type 채널 물질로 꼽히고 있다. 본 연구에서는 SWCNT를 성장하여 이를 이용한 전계효과 트랜지스터를 제작하고 또한, 부분적인 폴리머의 코팅으로 타입을 변화하는 연구를 보이고자 한다. Ferritin용액을 DI-water에 2000배 희석하여 SiO2 기판 위에 뿌린 뒤 Methanol을 이용하여 기판 표면에 촉매가 붙어있게 한다. 이 기판을 $900^{\circ}C$로 가열하여 유기물질을 제거한 뒤 화학 기상 증착(Chemical Vapor Deposition)방법으로 SWCNT를 성장하게 된다. 이렇게 성장된 SWCNT는 촉매의 농도에 비례하는 밀도를 가지게 되며 이 위에 전극을 증착하고 back-gate를 설치하여 FET를 제작한다. 메탈릭한 SWCNT는 breakdown 공정을 통하여 제거한 뒤, 전자 농도가 높은 NADH를 전체적으로 코팅을 한다. NADH는 기존의 다른 폴리머(polyethyleneimine: PEI)에 비교하여 코팅 후 전자 제공 효과가 크며 그 성질의 재현성이 높고 공기 중에서 안정성을 유지하는 능력이 있다. 이러한 NADH의 코팅으로 n-type으로의 SWCNT FET를 제작하였으며 type conversion 현상을 이용하면 국부적인 NADH의 코팅으로 homojunction-diode의 제작 등 다양한 소자의 제작에 적용될 것으로 예상한다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.23-26
• /
• 2003

An ultrasonic motor is a motor which uses vibration -a type of elastic vibration- to obtain a driving force, which then drives the motor using friction. In this paper, mode conversion type - single resonance mode ultrasonic rotary motor that use langevin type ultrasonic vibrator was studied. This model was proposed for the first time by Japanese Kumada in 1985. In this study, finite element analysis (FEA) of a stator and bidirectional driving characteristic of a rotor was newly obtained. The amplitude and phase of displacement and elliptical trajectory of beam was confirmed by FEA The fabricated motor was operated to clockwise and counterclockwise in 40.8 [kHz] and 44.2 [kHz] respectively. But bidirectional driving characteristics did not coincide each other.