• Journal of Power Electronics
• /
• 제5권2호
• /
• pp.99-103
• /
• 2005

In this paper, a novel circuit topology of a three-winding coupling inductor-assisting a high-frequency PWM boost chopper type DC-DC power converter with a high boost voltage conversion ratio and low switch voltage stress is proposed for the new energy interfaced DC power conditioner in solar photovoltaic and fuel cell generation systems. The operating principle in a steady state is described by using its equivalent circuits under the practical condition of energy processing of a lossless capacitive snubber. The newly-proposed power MOSFET boost chopper type DC-DC power converter with the three-winding coupled inductor type transformer and a single lossless capacitor snubber is built and tested for an output power of 500W. Utilizing the lower voltage and internal resistance power MOSFET switch in the proposed PWM boost chopper type DC-DC power converter can reduce the conduction losses of the active power switch compared to the conventional model. Therefore, the total actual power conversion efficiency under a condition of the nominal rated output power is estimated to be 81.1 ％, which is 3.7％ higher than the conventional PWM boost chopper DC power conversion circuit topology.

• 한국수소및신에너지학회논문집
• /
• 제24권6호
• /
• pp.535-542
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effect of bed insert geometry on CO conversion of WGS catalyst was measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and tablet shaped WGS catalyst and sand particle were used as bed materials. The cylinder type and the spring type bed inserts were used to hold the WGS catalysts. The CO conversion of WGS catalyst with the change of steam/CO ratio was determined based on the exit gas analysis. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. The measured CO conversion using the bed inserts showed high value comparable to previous results even though at low catalyst content. Most of input gas flowed through the bed center side when we charged tablet type catalyst into the cylinder type bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. However, the spring type bed insert showed good reactivity and good distribution of gas, and therefore, the spring type bed insert was selected as the best bed insert for SEWGS process.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -2
• /
• pp.1001-1004
• /
• 2000

RFID system is applied to identify, locate and track people, cars, animals. In RFID system, the passive transponder without battery has some benefits than active transponder, such as no restriction in battery exchange and in battery’s life. But it needs auxiliary RF-DC conversion circuit. RF-DC conversion circuit originated from Wireless Power Transmission (WPT). In this paper, RF-DC conversion circuit consists of a microstrip patch antenna and impedance matching circuit, Cock-croft Walton circuit. And RF-DC conversion circuits have two kinds of T-type and Cross-type impedance matching circuits.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.326-332
• /
• 2018

In this paper, the design process and the control method of the power conversion system (PCS) that consists of a bidirectional DC-DC converter and a 3-level T-type inverter for an energy storage system is presented. Especially the design method of the output LCL filter for a 3-lvel T-type inverter without complex mathematical process are proposed. The validity of the control method and design process in this paper are verified through simulation and experimental analysis.

• 반도체디스플레이기술학회지
• /
• 제16권2호
• /
• pp.19-26
• /
• 2017

The cure properties of ethoxysilyl bisphenol A type epoxy resin (Ethoxysilyl-DGEBA) systems with different hardeners were investigated, comparing with DGEBA and Diallyl-DGEBA epoxy resin systems. The cure kinetics of these systems were analyzed by differential scanning calorimetry with an isothermal approach, and the kinetic parameters of all systems were reported in generalized kinetic equations with diffusion effects. The Ethoxysilyl-DGEBA epoxy resin system showed lower cure conversion rates than DGEBA and Diallyl-DGEBA epoxy resin systems. The conversion rates of these epoxy resin systems with DDM hardener are lower than those with HF-1M hardener. It can be considered that the optimum hardener for Ethoxysilyl-DGEBA epoxy resin system is Phenol Novolac type. These lower cure conversion rates in the Ethoxysilyl-DGEBA epoxy resin systems could be explained by the retardation of reaction molecule movements according to the formation of organic-inorganic hybrid network structure by epoxy and ethoxysilyl group in Ethoxysilyl- DGEBA epoxy resin system.

• Journal of the Korean Physical Society
• /
• 제73권11호
• /
• pp.1650-1656
• /
• 2018

Photons generated via spontaneous parametric down-conversion (SPDC) have broad spectrums and suffer from dispersive broadening of the temporal wave packets when they are transmitted through dispersive media. In this paper we theoretically and experimentally study the detailed amount of the temporal broadening of the two-photon wave packets generated via both type-I and type-II SPDC with ${\beta}-BaB_2O_4$ of various lengths, by transmitting them through optical fibers. We interpret the results with respect to the spectral properties of the two-photon wave packets. We believe that our results will contribute to implementing protocols involving long-range distributions of photon pairs.

• 동력기계공학회지
• /
• 제17권1호
• /
• pp.27-35
• /
• 2013

SCR (Selective Catalytic Reduction) on DPF (Diesel Particulate Filter) is a multi-functional after-treatment device which integrates soot filtration and DeNOx function into a single can. Because of its advantage in package and cost, the SCR on DPF is considered as a potential candidate for future application. It inherently employes wall flow type monolithic reactor so ash included in exhaust gas may deposit inside the inlet channel of this device. This study is intended to identify the impact of ash deposit on SCR reaction under wall flow type monolithic reactor. Simulation approach is used so relevant species transport equations for wall flow type monolith is derived. These equations can be solved together with momentum conservation equations and give solution for conversion performance. Both ash deposit and clean catalyst case are simulated and comparison of these two cases gives an insight for the impact of ash deposit on conversion performance. Ash deposit can be classified as ash layer and ash plug. and impact of ash deposit is described along with different morphology of ash deposit.

• 한국실내디자인학회논문집
• /
• 제16권2호
• /
• pp.63-70
• /
• 2007

Analogy in problem solving is similarity-based reasoning facilitated by verbal and visual operation. This similarity-based reasoning generally supports initial phase of idea search. Therefore, this study intends to infer the types of problem solving by tracing the analogy use of verbal and visual representation through a experimental research. According to the result of this research, the types of problem solving by analogy are classified into 'evolving', 'divergent', and 'poor conversion' type. Firstly, 'evolving type' is distinguished between 'combination type' associated different contents to develope a new design and 'transformation type' associated similar words and sketches to be continuously revised and developed. In these types usually structural analogy rather than surface analogy is used. Secondly, in 'divergent type' associated words or sketches are individually represented, and among them one design solution is selected. In this type usually surface analogy is used. Thirdly, in 'poor conversion type' interaction between verbal representation and visual representation does not go on smoothly, and the generation of idea is poor. In here surface analogy is mostly used. These findings could form the basis of skill development of idea generation and conversion in design education.

• 한국수소및신에너지학회논문집
• /
• 제25권2호
• /
• pp.209-217
• /
• 2014

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor, a spring type bed insert was developed. In this study, effects of operating variables such as steam/CO ratio, gas velocity, syngas concentration on CO conversion were investigated in a fluidized bed reactor using the spring type bed insert to hold the WGS catalyst as tablet shape. CO conversion increased initially as the steam/CO ratio increased. But further increment of the steam/CO ratio caused decreasing of CO conversion because of increment of gas velocity and decrement of syngas concentration. Moreover, CO conversion decreased as the gas velocity increased and the syngas concentration decreased at the same steam/CO ratio. Continuous operation up to 48 hours (2 days) was carried out to check reactivity decay of WGS catalyst supported by spring type bed insert. The average CO conversion was 99.04% and we could conclude that the WGS reactivity at those conditions was maintained up to 48 hours.

• 한국인쇄학회지
• /
• 제16권3호
• /
• pp.133-146
• /
• 1998

The conversion of 1-Amino-4-(3'-Acetaminoanilino) Anthraquinone-2-Sulfonic Acid prepared by the Ullmann condensation have been investigated as a function of the reaction conditions such as catalysts, initial concentration of reactants, reaction temperature, pH, condensation agents and neutralizing agents. The experimental results showed that the Cu(I)-type catalysts had higher activity than the Cu(II)-type catalysts in this study. The conversion increased with increasing initial concentration of reactants but decreased at above critical concentration owing to agglomeration of reactants. It was also observed that the maximum conversion obtained at 7$0^{\circ}C$ and pH=7~8.