• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.1
• /
• pp.150-158
• /
• 2010

Filtering is necessary for the SRC(sample rate converter), that is used to change the sampling rate of a digital signal. The larger the conversion ratio of the sampling rate becomes, the more signal processing is needed for the filter, which means more complexity on realization. Thus it is important to reduce the amount of signal processing for the case of substantial conversion ratios. In this paper it is presented an efficient design method of a multistage FIR(finite impulse response) filter, with which the rate conversion occurs in stages rather than in one step. In this method, filter searching is performed exhaustively over all possible factorization of the conversion ratio, and also the filter complexity is measured based on direct realization rather than on estimation. It has been shown a designed multistage filter to have a less number of multiplications for filtering operation in comparison with a conventionally designed one. It has also been found that by allowing some variations of the filter architecture such as a halfband filter or a filter with multiple transition bands, the number of multiplications can be reduced further.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.1
• /
• pp.33-38
• /
• 2008

The probability of an oscillation occurrence in M/W frequency conversion repeaters is low on account of the different operating frequency of the input and output signals. The probability of interference caused by the M/W frequency conversion repeaters to other systems is also low because the systems are used in the line-of-sight. Therefore M/W frequency conversion repeaters are generally used for retransmitting the signal received from base station to the islands. This paper describes the design and implementation of analog predistorter for M/W frequency conversion repeaters in mobile communications. The M/W repeaters convert IF frequency of 1010+/-10MHz to RF frequency of 11GHz. A predistorter can be designed for the M/W repeater operating in either IF or M/W frequency. In this paper IF predistorter operated in 1010MHz is designed and implemented because a M/W predistorter operated in 11GHz is difficult to implement. The IF predistorter can linearize RF modules in the repeater followed by IF stages. The performance test results show that the implemented analog predistorter improves ACPR of 10dB at the output power of 25dBm with the signal frequency of 10.805GHz.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.384-387
• /
• 1990

This paper describes the design of the power conversion system for the 3-ton prototype magnetic levitation system. Electric power needed for the propulsion and levitation system of the vehicle is supplied by the wayside rectifier through the power rail and is picked up by the on board power collector, and is supplied to the propulsion VVVF inverter and levitation chopper. In this paper, design characteristic of the VVVF inverter, chopper and power source unit which provides control power to the levitation controller and levitation power to the chopper is described.

• The Journal of Information Technology and Database
• /
• v.1 no.1
• /
• pp.9-30
• /
• 1994

The objective of this paper is to give a brief review of relational design methodology, and show how a relational schema can be converted into an object-relational schema. We first introduce relational terminology and describe the relational design process along with its limitations. Next we show how the relational model can be extended to overcome these limitations : these extensions form the core of an object-relational data model ; we use the UniSQL/X data model as an example. We illustrate the process or converting a relational schema into an object-relational schema, and show the benefits of this conversion with respect to queries. The conversion process is then summarized as a set of guidelines. Finally, we make our conclusions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.8
• /
• pp.490-495
• /
• 2015

This paper was proposed the theoretical research and optimal design 3,000 V IGBT for using electrical automotive, high speed train and first power conversion. To obtaining 3,000 V breakdown voltage, the design parameters was showed $160{\Omega}{\cdot}cm$ resistivity and $430{\mu}m$ drift length. And to maintain 5 V threshold voltage, we obtained $6.5{\times}10^{13}cm^{-2}$ p-base dose. We confirmed $24{\mu}m$ cell pitch for maintain optimal on state voltage drop and thermal characteristics. This 3,000 V IGBT was replaced to thyristor devices using first power conversion and high speed train, presently.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1002-1006
• /
• 2015

In this paper, design and analysis of permanent magnet synchronous generator for ocean thermal energy conversion (OTEC) considering magnetically coupled turbine-rotor system is discussed. In particular, the rotor dynamics considering bearing span and journal shaft diameter is highlighted. The two topologies of permanent magnet synchronous generator with magnetic coupling are employed for comparison of computed rotor dynamics and generating characteristics. The analysis results show that the critical speed of the turbine-rotor system is higher when the rotor is coupled by magnetically coupling. Finally, the experimental results confirmed the validity of the proposed design and analysis scheme and successful development.

• Current Optics and Photonics
• /
• v.1 no.2
• /
• pp.150-156
• /
• 2017

A diffraction limited optical system for head mounted displays (HMDs) was designed. This optical system consists of four modules, including 1:5 mm and 5:30 mm beam expanders, polarization grating-polarization conversion system (PG-PCS) and refractive/diffractive projection optical module. The PG-PCS module transforms the unpolarized Gaussian beam to a linearly polarized beam and it simultaneously homogenizes the spatial intensity profile. The optical projector module has a $30^{\circ}$ field of view, a 22 mm eye relief, and a 10 mm exit pupil diameter with a compact structure. Common acrylic materials were utilized in the optical design process; therefore, the final optical system was lightweight. The whole optical system is suitable for a 0.7 inch liquid crystal on silicon microdisplay (LCOS) with HDTV resolution ($1920{\times}1080$) and $8.0{\mu}m$ pixel pitch.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.12
• /
• pp.1009-1014
• /
• 2001

The ladder diagram (LD) for programmable logic controllers (PLCs) ar responsible for much important roles in advance industrial automation. As automated systems become more complex the design procedures of the system become more difficult as well. Hence. the design automation issues based on discrete event models(DEMs) are receiving more attention. One of the popular ways of tackling these problems is employing Petri nets. In this paper, we use the modified automation Petri net(MAPN) to model the manufacturing system and the modified token passing logic (MTPL) method conversion (ECC) algorithm based on the MAPN and the MTPL Finally, an example of the manufacturing system is provided to illustrate the proposed ECC algorithm.

• Korean Journal of Computational Design and Engineering
• /
• v.7 no.2
• /
• pp.121-130
• /
• 2002

The concept of Level Of Detail (LOD) was introduced and has been used to enhance display performance and to carry out certain engineering analysis effectively. We would like to use an adequate complexity level for each geometric model depending on specific engineering needs and purposes. Solid modeling systems are widely used in industry, and are applied to advanced applications such as virtual assembly. In addition, as the demand to share these engineering tasks through networks is emerging, the problem of building a solid model of an appropriate resolution to a given application becomes a matter of great necessity. However, current researches are mostly focused on triangular mesh models and various operators to reduce the number of triangles. So we are working on the multi-resolution of the solid model itself, rather than that of the triangular mesh model. In this paper, we propose multi-resolution representation of B-rep model by reordering and converting design features into an enclosing volume and subtractive features.

• Korean Journal of Optics and Photonics
• /
• v.9 no.5
• /
• pp.282-290
• /
• 1998

The equivalent lens conversion technique is applied to design achromatic doublet and aplanatic doublet. A thin doublet which has zero axial thicknesses, are corrected for the third order aberrations at first, and the thin doublet is converted into thick lens system by using the equivalent lens conversion. Two types of cemented doublets, the Fraunhofer type and the Steinheil type, are designed by using a crown glass BaK-2 and a flint glass SF-2. In the thin doublet design, there are two achromatic solutions and a aplanatic solution for the both types.