• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.61-65
• /
• 1996

This paper experimentally describes the grinding characteristic of discontinuous grinding wheels in creep-feed grinding. In creep-feed grinding, grinding temperature increases rapidly and thermal damage such as a burn occurs on a workpiece. Discontinus grinding wheel with Conventional grinding wheel shows an exellent cooling effect has been developed. The wheels have 6, 12, 24 pieces of slotted which compare with characteristics of each wheels

• 한국정밀공학회지
• /
• 제15권9호
• /
• pp.145-151
• /
• 1998

In this study, the experimental and analytic investigation with cold air system has been performed for improving the working environment of the conventional grinding fluid. Very simple cold air system was developed which could replace by the conventional grinding fluid system. The identification of heat of grinding Bone is very important for precision grinding. The experimental data was analysed to investigate the heat which was transferred to the workpiece. It was found that 45∼55％ of the total energy for dry grinding, 22∼28％ for wet grinding, and 32∼35％ for cold air system are conducted to the workpiece in grinding with cubic boron nitride wheel. Cubic boron nitride wheel could reduce the residual stress and thermal demage comparing with aluminium oxide wheel, because cubic boron nitride wheel has very high extreme thermal conductivity.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.52-59
• /
• 1996

Conventionally, grinding of stainless steel, aluminium ally, copper alloy, and titanum alloy are difficult to obtain the high quality finish, because they have the mechanical properties such as low hardness, high toughness which result in the loading of wheel and the poor surface finish. Inorder to perform the grinding operations for these sorts of materials easily, the discontinuous grinding wheel with multi-porous grooves has newly been developed. The multi-porous grooves were formed during wheel production. This discontinous grinding wheel increases the grinding performance. It is desirable to use the discontinuous grinding wheel when grinding materials wiht high efficiency and accuracy which is impossible by conventional wheels. In this paper, the constructing and manufacturing method of grinding wheel with multi-proous grooves are explained, and the grinding charateristics of discontinuous grinding wheel are also illustrate.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1996년도 춘계학술대회 논문집
• /
• pp.108-113
• /
• 1996

Conventionally, grinding of stainless steel, aluminium alloy, copper alloy, and titanum alloy is difficult due to the mechanical properties such as low hardness, high toughness which result in the loading of wheel and the poor surface finish. In order to grind this sort of materials easily, discontinuous grinding wheel with multi-porous grooves was newly developed. The multi-porous grooves were formed during wheel production. This discontinuous grinding wheel drastically increases the grinding performance. It is desirable to use the discontinuous grinding wheel when grinding materials with high efficiency and accuracy which is impossible by conventional wheels. In this paper, the construction and manufacturing method of grinding wheel with multi-porous grooves are explained. The grinding charateristics of discontinuous grinding wheel was also illustrated.

• 대한기계학회논문집A
• /
• 제20권9호
• /
• pp.2866-2874
• /
• 1996

In the grinding of difficult-to-materials, the major problmes of conventional grinding are grinding burn, wheel wear, grinding surface crack, loading and glazing, When a conventioanl grinding wheel is used, wheel wear and grinding surface crack easily occur in low heat conductive material and annealed steel. Intermittent grinding is suitable for diffcult-to-matrical such as stainless steel, titanium alloy, aluminum alloy and copper alloy. The purpose of this paper is to develop a new type intermittent wheel of the grinding system for improving the problem of stainless steel grinding, to observe the effect of intermittent grinding on surface quality and grinding characteristics of stainless steel grinding using intermittent grinding wheel. The characteristics of intermittent grinding system improve surface quality, low grinding temperature and low loading.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.857-861
• /
• 1997

In discontinuous wheel grinding, temperature is different form conventional grinding. The characteristics of discontinuous grinding with respect to various slotted wheel were compared with those of general grinding. Thermal conditions vary with intermittent ratio, direction of fluid supply for discontinous wheel. According to three direction of grinding fluid supply and intermittent ratio,temperature and surface roughness were analyzed.

• 한국정밀공학회지
• /
• 제13권12호
• /
• pp.38-45
• /
• 1996

A new grinding wheel was developed for the high performance grinding of difficult-to-grinding materials. The grinding performance of the newly developed wheel including grinding forces, grinding ratio, and surface roughness of ground surface was evaluated through experiments. Experimental results show that the performance of the newly developed wheel is superior to the conventional alumina wheel and comparable to the Sol-gel wheel. An experimental investigation on the wear of alumina grinding wheel was also carried out. The experiments consist of the measurements of fracture strength of the abrasive grains, grinding force, and the area of wear flats of grinding wheels. Microscopic examination of abrasive grains was executed to observe the progress of wheel wear. The results indicate that the 32A grain, which has relatively lower fracture strength, wears out faster than 5SS and 5SG. The wheel wear occurs much faster in wet grinding than in dry grinding. It has also been found that the grinding forces increase logarithmically with increasing wear flats.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.118-123
• /
• 1995

A new grindignwheel was developed for the high performance gfinding of difficult-to-grind materials. Te grinding performance (such as grinding forces, grinding ratio, and surface roughness of ground surface) of the newly developed wheel was evaluated through experiments. Experimental results show that the performance of the newly developed wheel is superior to conventional alumina wheel and comparable to the S-G wheel.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.9-16
• /
• 2013

The comparisons of performance characteristics between the super-mirror face grinding machine using variable air pressure developed in this laboratory to grind precisely the sliding face of a surface hardened workpiece with thermal spray and the conventional one are investigated by measuring the surface roughness and hardness for a SCM440. To process variously workpiece according to shape, size and materials, the rotating and contacting forces of the developed grinding machine can be changed by air pressure. The surface roughness of processed workpiece can be also attained to state of mirror face by grinding precisely the sliding face with changing the rotating speed of diamond wheel. It is possible to be attached to the various machine tools because the super-mirror face grinding machine using variable air pressure is a small size. The grinding efficiency is elevated because it can be worked by two or more grinding machines attached to concurrently a machine tool for the large workpiece. In this study, results show that the cusp height of the super-mirror face grinding machine for the particle size of 100 and $1500No./mm^2$ is lower than that of the conventional one because the vibration is reduced by rotating very fast the diamond wheel with a pressed air and it can be processed by rotating the diamond wheel with a constantly varied air pressure perpendicular to workpiece surface, and that the workpiece in the super-mirror face grinding machine for the particle size of $3000No./mm^2$ can be processed to state of mirror face that is rarely seen by the cusp height. It is also found that the surface hardness of both the conventional and the super-mirror face grinding machines are increased as the particle size of diamond wheel is reduced, and the surface hardness of the super-mirror face grinding machine is HRC 1.1 ~ 1.8 higher than that of the conventional one.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.38-49
• /
• 1994

In this study, grindability of some representative engineering ceramics are experimentally investigated using resin bond diamond wheel with conventional surface grinding machine, and proper grinding conditions which can be obtained from various experimental results are established also for mechanical components which are proper to domestic circumstances with high reliability. And through the results of experiment, it is confirmed that grinding energies of the ceramics, especially in the case of $Al_2O_3$, are lower than steel with same machining condition in the conventional grinding because of their fine-brittle fracture mode type removal process, though the ceramics are well-known to unmachinable materials. And moreover, the total pass numbers needed for spark-out process to be completed are depend on their mechanical properties because that grinding stiffness is different from each other. The grinding force, ginding power and ground surface roughness are also measured and compared. Furthermore, the experiments carried out in this study, some useful results are obtained with can guide to grind engineering ceramics with conventional surface grinding machine.