• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.3
• /
• pp.54-62
• /
• 2002

This paper describes a development of the integrated controller system for car electrical signal and sensor input/output control with CAN communication protocol. In order to improve the system reliability and effectiveness for the conventional controller using the wiring harness, a detailed integrated control system is introduced and discussed. The CAN communication protocol is a robust control method with serial bus system for the control of distributed module in the multiplexed network. Therefore, this has high reliability and flexibility in the overall control system implementation. This paper proposes an integrated system with high reliability and stability for control of various car signal, and evaluates the effectiveness of the system using the actual implementation. For these purposes, after a brief of the main features of the CAN will be addressed, this paper presents the result of development of the integrated hardware system and overall control program.

• Journal of Korean Society of Transportation
• /
• v.26 no.5
• /
• pp.63-72
• /
• 2008

Signalized intersections are operated without a signal preemption control strategy in Korea, thus there is no priority treatment for an emergency vehicle passing through the intersections. In this paper, a signal preemption control strategy is introduced to improve the safety and operational efficiency of an emergency vehicle. Using the micro simulation tool, the effects on delay and travel speed of the signal preemption control strategy are analyzed for various traffic conditions to identify the general performance trends. Then, another simulation analysis is performed to verify the feasibility of the control strategy using real network data collected from field study. Results show that the preemption control strategy provides the positive impact on emergency vehicles' operation, but the positive impact is reduced as the v/c ratios increase. As expected, the average delays of the normal vehicles are slightly increased, but the magnitude is not significant. Therefore, it is expected that the introduction of the preemption control strategy in Korea would produce the positive social benefits.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1381-1386
• /
• 2019

As traffic congestion in cities becomes more serious, intelligent traffic control is actively being researched. Reinforcement learning is the most actively used algorithm for traffic signal control, and recently Deep reinforcement learning has attracted attention of researchers. Extended versions of deep reinforcement learning have been emerged as deep reinforcement learning algorithm showed high performance in various fields. However, most of the existing traffic signal control were studied in a single intersection environment, and there is a limitation that the method at a single intersection does not consider the traffic conditions of the entire city. In this paper, we propose a cooperative traffic control at multi-intersection environment. The traffic signal control algorithm is based on a combination of extended versions of deep reinforcement learning and we considers traffic conditions of adjacent intersections. In the experiment, we compare the proposed algorithm with the existing deep reinforcement learning algorithm, and further demonstrate the high performance of our model with and without cooperative method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.6
• /
• pp.890-896
• /
• 2022

In this paper, gimbal camera control through smart gloves was implemented to increase convenience and accessibility to the control of drones used in various fields. Smart gloves identify human gestures and transmit signals through Bluetooth. The received signal is converted into a signal suitable for the drone through a GCS (Gound Control Station). Signals from smart gloves are expressed in a quaternion method to prevent gimbal locks, but for gimbal cameras, conversion is required to use Roll, Pitch, and Yaw methods. The data conversion mission is performed in the GCS. The GCS transmits an input signal to the control board of the drone through Wi-Fi. The control board generates and outputs the transmitted signal in a PWM manner. The output signal is input to the gimbal camera through the SBUS method and controlled. The input signal of the smart glove averaged 0.093 s and up to 0.099 s to output to the gimbal camera, showing that there was no problem in real-time use.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1231-1234
• /
• 2003

A sensor working in outdoor may generate some faulty signal owing to dust and high temperature. This paper describes an intelligent sensor system and controller which has a reconstruction mechanism for faulty signal. The faulty signals are dievided into two types as linear distortion and non linear distortion, respectively. The linear distorted signal is due to dust, and non linear distorted signal is due to physical breakdown of sensor or high temperature. These distorted signal have been reconstructed by the proposed method based on polynomial regression method and principal component analysis approach.. The proposed method has been applied to sun tracking system working in outdoor. For a robust and precision control of sun tracker, a fuzzy controller was also proposed. The fuzzy controller controls the tracker by using the collected sensor signal. The tolerance of the position control is within 1.5 degree. To show the validity of the developed system, some experiments in the field were illustrated.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.4
• /
• pp.11-21
• /
• 2013

The conventional real-time signal control strategy for oversaturated situation generally requires a number of detectors at the intersection in order to identify the queue length at each approach. Also, existing strategy for the spillback has limited effect due to the temporal spillback control which only reduce the green split at the approach. In this study, a signal control system utilizing the imagery information from ITS roadside equipment is developed for operation of oversaturated intersections. The strategy calculates the saturation ratio based on the queue length extracted from ITS RSE, and designs the signal control variables according to the saturation ratio. The signal control strategy is divided into two phases: oversaturated and supersaturated. In oversaturated conditions, timing plan for main approach is optimized by the queue length. In oversaturated conditions where spillback might occur, the signal timing is designed in order to avoid the spillback. To increase field adaptability, the strategy is designed to adjust the split length, all-red-time, and clearance time, and keep the major signal control variables intact. The result of the simulation shows that in oversaturated conditions, the improvement is similar to the real-time signal control system. In case of, oversaturated conditions, however, the effect of the strategy is superior to that of a real-time system.

• The Journal of the Korea Contents Association
• /
• v.16 no.8
• /
• pp.671-680
• /
• 2016

This research suggested a new real-time traffic signal control algorithm using fusion data of the travel time and the occupancy rate. This research applied the travel time data of traffic information system to traffic signal operation, and developed the signal control process using the degree of saturation that was estimated from the travel time data. This algorithm estimates a queue length from the travel time based on a deterministic delay model, and includes the process to change from the queue length to the degree of saturation. In addition, this model can calculate the traffic signal timings using fusion data of the travel time and the occupancy rate based on the saturation degree. The micro simulation analysis was conducted for effectiveness evaluation. We checked that the average delay decreased by up to 27 percent. In addition, we checked that this signal control algorithm could respond to a traffic condition of oversaturation and detector breakdown effectively and usefully. This research has important contribution to apply the traffic information system to traffic signal operation sectors.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.5
• /
• pp.49-56
• /
• 2004

A low power consuming voice signal processing and control module was designed using a small $\mu$-controller for use in a totally implantable middle ear system. The module was designed that it can control the implanted system as well as process the fitting algorithm of input sound signal. In ordinary operation mode, the $\mu$-controller processes the applied sound signal for compensating the hearing loss of the patients. When the control signal is applied from the IR receiving module, the $\mu$-controller interrupts the signal processing and executes the order of the control signals such as power on/off, volume up/down. The designed module was implemented and verified the performance of the system through several experiments.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.2
• /
• pp.113-127
• /
• 2018

This study develops a fusion priority signal control algorithm to pass without delay in emergency events. Fusion priority signal control is method combined center control with local control. The center control method applies signal times for each signalized intersection on the emergency vehicle's route when an emergency call is received. As signals are controlled before the emergency vehicle leaves for its destination, it is possible to clear the queues at each intersection more effectively. However, since the traffic information (speed, position) of the real-time emergency vehicle is not used, the intersection arrival time predicted by center control and actual arrival time of the emergency vehicle may be different from each other. In the case, it is possible to experience a delay caused by the signal. Local control method operate priority signal use the real-time information of EV, but there is a limitation that queue elimination time can not be reflected. In this study, fusion(center+local) control algorithm is proposed to compensate the disadvantages of center and local control also maximizing its advantages. Proposed algorithm is expected to decrease delay time of EV in emergency situation.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.1127-1128
• /
• 2008

In this paper, we propose a control method to improve control performance for a Quad-rotor Unmanned Aerial Vehicle's stabilization. The proposed method is the Fuzzy+I control that contains a fuzzy controller which processes signals from the error and the change of error, and generates the control signal by summing up fuzzy output signal and integral signal. We simulated and experimented on the fuzzy+I control method by implementing Quad-rotor UAV that is able to hovering, for the purpose of verifying the effectiveness of the proposed fuzzy+I control method in comparison with general PID control, and we found out that fuzzy+I controller improved control performance of the system.