• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.12
• /
• pp.1885-1891
• /
• 2010

Torque control of wind turbines is important when the wind speed is below the rated speed. The main objective of torque control is to extract the maximum power from the potential aerodynamic power of the wind. Torque control methods for wind turbines are classified as torque-mode control and speed-mode control. In torque-mode control, which is well known and traditionally used in many wind turbines, the torque demand of the generator is proportional to the square of the generator speed. In speed-mode control, a PI controller is used to generate the appropriate torque demand of the generator. In this study, the two torque control methods mentioned above are applied to a 2.75-MW wind turbine; simulation results for real turbulence wind speeds are presented, and the response properties are compared.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1663-1674
• /
• 2017

This paper deals with the robust speed regulation of a surface-mounted permanent magnet synchronous motor (SPMSM) that is subject to parametric uncertainties and external disturbances. The proposed approach retains a conventional cascade control configuration composed of an outer-loop speed control module and inner-loop current control modules. Baseline proportional-integral (PI) controllers are designed for nominal modular systems without accounting for the uncertainties to set a desired control performance of the closed-loop system. After studied in both frequency and time domains, a reduced-order proportional-integral observer (PIO), as a modular disturbance observer, is incorporated with each control module to maintain the ideal performance of the modules. Theoretical analysis confirms the desired performance recovery of the augmented system with modular PIOs to the nominal system. Comparative computer simulations and experimental results validate the proposed cascade control method for SPMSM speed regulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.2
• /
• pp.151-157
• /
• 1999

In this paper, an integrated nonlinear sliding mode observer and controller has been designed in order to control of an automotive engine idle speed. The primary objective of the engine idle speed control is to maintain the desired engine idle speed despite of various torque disturbances via estimating air mass flow at the location of the injector in intake manifold by using a sliding mode observer. Simulation results show that the case where both throttle angle and ignition time are used as control inputs outperforms the case where just only throttle angle is used as a control input.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.736-741
• /
• 1998

It is well known that an encoder or a resolver is necessary to obtain the position data for speed or position control Generally utilized speed sensors are mal-affected by the EMI, dusty, and high temperature surroundings. Therefore, the speed and position sensorless controls using observers have been studied widely. In this paper, the binary observer which is composed of two feedback regulation loops to control the speed of SRM(Switched Reluctance Motor) is applied. One loop compensates the control input directly like the sliding mode control, and the other one compensates the system parameters indirectly. This observer is constructed on the foundation of variable structure control on the foundation of variable structure control theory and has the inertial term for the varying parameter. The validities of this proposed method is proved by experiments.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.6
• /
• pp.2289-2297
• /
• 2017

Applying a periodic load torque to an AC motor generates a ripple, which is synchronized to the frequency of the periodic load torque, at the speed of the motor. Consequently, numerous studies have focused on reducing the speed ripple caused by the load torque. However, it is difficult to reduce the speed ripple when there is a time delay in acquiring speed information, such as that from a sensorless control. Therefore, we propose a speed control method for reducing speed ripples caused by a periodic load torque when there is a time delay in acquiring the speed information. The proposed method is verified by conducting simulations using the Simulink program from MATLAB, and by applying the method to an actual motor in which speed ripples occur due to a periodic load torque that is synchronized with the speed of the motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.1188-1193
• /
• 1993

For the HST(Hydrostatic Transmission) consisted of a variable displacement axial piston pump and motor, a speed controller with efficiencies considered is proposed. To consider a efficiency in speed control, the displacements of pump and motor which maximize a steady state efficiencies with a various load torque are calculated through computer simulation and these results are reflected to speed controller which has PI control structure with cross over control scheme. It is shown through computer simulation that the proposed controller gives better steady state efficiencies compared with the conventional controller and good transient responses.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.376-379
• /
• 1998

This paper be described the constant speed control of induction motor for high performance. Vector control system which is used the stator current, voltage of IM is modeled without the speed, flux sensor. The proposed control system be simulated using Matlab with Simulink. Results include the fast response of the constant speed and torque in proposed system. For high performance, this paper presents the robust characteristics of field oriented control system for IM.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.2
• /
• pp.81-87
• /
• 1996

Time delay control(TDC) law has been recently suggested as an effective control technique for nonlinear time-varying systems with uncertain dynamics and/or unpredictable disturbances. This paper focuses on the applications of the TDC algorithm to torque control of an engine system and speed control of an engine/automatic transmission system. Through the stability analysis of the engien system based on TDC, determination of the appropriate time delay and control factor is investigated. It was revealed that the size of time delay of the TDC law should be greater than that of transport delay of the system for both stability and better control performance. Simulation and experimental results for the engine torque control and engine/automatic transmission speed control systems show both relatively good command following and disturbance rejection properties. However, TDC controller shows rather slow responses when applied to the system with large transport delay.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1115-1119
• /
• 2007

Five control methods (Speed Control, PID Gain Scheduling, Loop Time Control, Simple PID, Switching Control) have been applied to the control of an Inline Co-axial valve by the simulation of AMESim. The simulation results have shown that the speed control method is the most stable and the fastest way to reach to the set point in the simulation of the flow control. Moreover, It has been found that the five control methods have the almost same characteristics in the power consumption, the counter electromotive force, and the motor angular velocity. According to the analysis results, the fast and stable control characteristics of the speed control method is the most suitable for the flow control using a inline co-axial valve with a DC(BLCD) motor.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.12
• /
• pp.541-554
• /
• 1986

This paper presents the results of driving performance analysis of permanent magnet synchronous motor using a microprocessor based control system. The system consists of three phase power transistor inverters, three phase controlled rectifier, three central processing units, and sensors. The three CPUs are, respectively, used to generate PWM control signals for the inverter generating three phase sine wave, to generate the gate control signals for firing the converter, and to supervise other two CPUs. The supervisor is used to compute PI control algtorithm to three phase reference sine wave for the inverter. It is also used to maintain a constant voltage frequency ratio for the converter operating as a constant torque controller. The inverter CPU retrieves precomputed PWM patterns from look up tables because of computation speed limitations found in almost available microprocessors. The converter CPU also retrieves precomputed gate control patterns from another look-up tables. For protecting the control ststem from any damage by extraordinary over currents, the supervisor receives the data from current sensor, CT, and break down the CB to isolate the circuits from source. A resolver has a good performance characteristics of overall speed range, especially on low speed range. Therefor the speed control accuracy is impoved. The microprocessor based PM synchronous motor control system, thus, has many advantages such as constant torque characteristics, improvement of wave, limitation on extraordinary over currents, improvement of speed control accuracy, and fast response speed control using multi-CPU and look-up tables.