• Smart Structures and Systems
• /
• 제25권6호
• /
• pp.751-764
• /
• 2020

Real-time monitoring of stiffness and strength in cement based system has received significant attention in past few decades owing to the development of advanced techniques. Also, use of environment friendly supplementary cementitious materials (SCM) in cement, though gaining huge interest, severely affect the strength gain especially in early ages. Continuous monitoring of strength- and stiffness- gain using an efficient technique will systematically facilitate to choose the suitable time of removal of formwork for structures made with SCM incorporated concrete. This paper presents a technique for monitoring the strength and stiffness evolution in hydrating fly ash blended cement systems using electro-mechanical impedance (EMI) based technique. It is important to observe that the slower pozzolanic reactivity of fly ash blended cement systems could be effectively tracked using the evolution of equivalent local stiffness of the hydrating medium. Strength prediction models are proposed for estimating the strength and stiffness of the fly ash cement system, where curing age (in terms of hours/days) and the percentage replacement of cement by fly ash are the parameters. Evaluation of strength as obtained from EMI characteristics is validated with the results from destructive compression test and also compared with the same obtained from commonly used ultrasonic wave velocity (UPV). Statistical error indices indicate that the EMI technique is capable of predicting the strength of fly ash blended cement system more accurate than that from UPV. Further, the correlations between stiffness- and strength- gain over the time of hydration are also established. From the study, it is found that EMI based method can be effectively used for monitoring of strength gain in the fly ash incorporated cement system during hardening.

• 한국분말재료학회지
• /
• 제15권1호
• /
• pp.31-36
• /
• 2008

In this study, the bottom-up powder metallurgy and the top-down severe plastic deformation (SPD) techniques for manufacturing bulk nanomaterials were combined in order to achieve both full density and grain refinement without grain growth of rapidly solidified Al-20 wt% Si alloy powders during consolidation processing. Continuous equal channel multi-angular processing (C-ECMAP) was proposed to improve low productivity of conventional ECAP, one of the most promising method in SPD. As a powder consolidation method, C-ECMAP was employed. A wide range of experimental studies were carried out for characterizing mechanical properties and microstructures of the ECMAP processed materials. It was found that effective properties of high strength and full density maintaining nanoscale microstructure are achieved. The proposed SPD processing of powder materials can be a good method to achieve fully density and nanostructured materials.

• 한국세라믹학회지
• /
• 제12권2호
• /
• pp.3-9
• /
• 1975

The continuous grading method of pyrophyllite particles was adopted to prepare the refractories for ladle. The optimum conditions of fabrication adjusting the binders, the amount of water, the forming pressure and the firing temperature were investigated. The various properties, such as strength, density, porosity, thermal shock, corrosion resistance to slag were measured and compared with properties of ladle bricks presently used at local steel plants. The specimen studied in the present investigation showed a rather superior properties to theconventional product available locally.

• 한국지반신소재학회논문집
• /
• 제7권2호
• /
• pp.1-5
• /
• 2008

일반적인 콘크리트 건축물이나 도로포장에서 발생되는 부등침하는 건물의 붕괴나 도로의 수명저하로 인한 비용을 증가시킨다. 이에 대하여 침하된 구조물 하부지반에 그라우팅 공법을 이용하여 지반침하복원을 실시한다. 그러나 기존 그라우트 공법의 경우, 강도발현기간이 길고, 보강효과가 지속적이지 못한 단점을 지니고 있다. 이를 보완하기 위한 주입재료로써, 고밀도 팽창 재료의 특성을 평가하였다. 지반상태와 팽창재료의 주입량의 변화에 따른 압축강도의 변화와 화학물질에 대한 안정성 시험 및 SEM 촬영을 통하여 특성을 연구하였다. 압축강도는 다른 물질과의 혼합으로 높은 강도가 발현되었으며, 화학적 저항성은 대부분의 조건에서 반응하지 않았으나 알코올계열에 변화가 발생하였다. SEM 촬영을 통하여 강도발현에 있어서 조직구성이 촘촘할수록 치밀하게 구성된다고 판단하였다.

• Management Science and Financial Engineering
• /
• 제16권3호
• /
• pp.71-84
• /
• 2010

In this study, we present the exact methods of transforming the continuous solutions into the discrete ones for two types of bit-loading problem, marginal adaptive (MA) and rate adaptive (RA) problem, in multicarrier communication systems. While the computational complexity of existing solution methods for discrete optimal solutions depends on the number of bits to be assigned (R), the proposed method determined by the number of subcarriers (N), making ours be more efficient in most cases where R is much larger than N. Furthermore our methods have some strength of their simpler form to make a practical use.

• 한국임상수의학회지
• /
• 제39권6호
• /
• pp.353-359
• /
• 2022

Several suture patterns can be used for cystotomy closure, and a continuous suture pattern is the most commonly used. In this study, the fluid-tight ability and other suitabilities of continuous appositional sutures, such as the simple continuous suture pattern (SC), running suture pattern (RN), and Ford interlocking suture pattern (FI), were compared for cystotomy closure. Cystotomy closure was performed using each suture method in 10 cases of ex vivo swine bladders in each group. Suture time, leakage site, suture length, bursting pressure (BP), bursting volume (BV), and circular bursting wall tension (CBWT) were measured. Suture time and suture length were the shortest in RN and the longest in FI. Leakage occurred in two places: the incision line directly and the hole made by the suture. Leakage occurred through the incision line in 4 bladders of the RN group and 2 bladders of the FI group, but not in the SC group, and in the rest of the bladders, leakage occurred through the suture hole. The values of BP, BV, and CBWT increased in the order of FI, SC, and RN. Suture time and suture length can be considered as factors related to healing and side effects. In this study, leakage through the incision was found in a less appositional area; therefore, leakage through the hole could be considered an indicator of better apposition. Good apposition is one of the conditions required for ideal cystotomy closure. The bursting strength representing the fluid-tight ability can be expressed as the CBWT. RN is expected to be efficient and cause a small degree of foreign body reaction; however, it is expected to be less stable. FI has the greatest fluid-tightness ability, but it has been proposed that side effects due to foreign body reactions most frequently occur in FI. In conclusion, SC, which is expected to have a sufficient degree of fluid-tightness and appropriate recovery, is preferable to other continuous appositional suturing methods for cystotomy closure.

• Transactions on Electrical and Electronic Materials
• /
• 제1권3호
• /
• pp.23-28
• /
• 2000

A block-oxide layer was formed on the surface of Cu-based leadframe by chamical oxidation method in order to enhance the adhesion strength between Cu-based leadframe and epoxy molding compound (EMC) Using sandwiched double cantilever beam (SDCB) specimens, the adesion strength was measured in terms of interfacial fracture toughness, G$\sub$IC//Results showed that the black-oxide layer was composed of two kinds of layers: pebble-like Cu$_2$O layer and acicular CuO layer, At the initial stage of oxidation the Cu$_2$O layer was preferentially formed and thickened up to around 200 nm whithin 1 minute of the oxidation time. Then the CuO layer started to from atop of the Cu$_2$O layer and thickened up to around 1300 nm until 20 minutes. As soon as the CuO layer formed, the thickness of Cu$_2$O layer began to reduce and finally reached to around 150 nm. The pre-cleaned and the Cu$_2$O coated leadframes showed almost no adhesion of EMC, however, as the CuO precipitates appeared and became continuous, G$\sub$IC/ increased up to around 80 J/㎡. Further oxidation raised G$\sub$IC/ up. to around 100 J/㎡.

• 대한토목학회논문집
• /
• 제30권6A호
• /
• pp.513-523
• /
• 2010

I-거더 형식의 연속교 교각 부근에서는 큰 부모멘트가 작용하게 되며 이로 인하여 소성힌지가 생성된다. 소성힌지가 형성됨에 따라 교각 부근의 부모멘트는 감소하게 되며, 정모멘트부의 휨모멘트는 반대로 증가하게 된다. 이러한 모멘트 재분배가 원활히 발생하기 위해서는 소성힌지가 충분한 휨연성 혹은 단면회전 능력을 가지고 있어야 한다. 하지만 고강도 강재에 있어 재료연성이 다소 떨어지는 경향이 있고, 재료의 항복응력이 증가할수록 I-거더의 탄성 변형량은 이에 비례하여 증가하므로, 소성변형 능력 및 휨연성이 감소하는 것으로 알려져 있다. 따라서, 고강도 강재를 I-거더 형식의 연속교에 적용할 때 동일한 수준의 휨연성을 확보할 수 있는 방안에 대한 연구가 필요하다. 본 연구에서는 유한요소해석 및 실험 연구를 통하여 항복강도 680 Mpa급 강재 적용 I-거더의 휨연성 평가 및 휨연성 확보 방안에 대하여 연구를 수행하였다. 연구 결과 재료의 인장 강도가 증가함에 따라 탄성 변형이 증가하며 소성 변형 능력이 저하됨으로 I-거더의 휨연성이 현저하게 감소하는 것으로 나타났으며, I-거더의 휨연성 확보를 위하여 부등간격으로 가로보를 배치하는 방안을 제안하였다. 최종적으로 가로보부등배치가 I-거더의 휨연성에 미치는 영향을 실험적으로 검증하였다.

• BMB Reports
• /
• 제37권5호
• /
• pp.629-633
• /
• 2004

NADPH-cytochrome P450 reductase (CPR) transfers electrons from NADPH to cytochrome P450, and catalyzes the one-electron reduction of many drugs and foreign compounds. Various forms of spectrophotometric titration have been performed to investigate the electron-accepting properties of CPR, particularly, to examine its ability to reduce cytochrome c and ferricyanide. In this study, the reduction of 1,1-diphenyl-2-picrylhydrazyl (DPPH) by CPR was assessed as a means of monitoring CPR activity. The principle advantage of DPPH is that its reduction can be assayed directly in the reaction medium by a continuous spectrophotometry. Thus, electrons released from NADPH by CPR were transferred to DPPH, and DPPH reduction was then followed spectrophotometrically by measuring $A_{520}$ reduction. Optimal assay concentrations of DPPH, CPR, potassium phosphate buffer, and NADPH were first established. DPPH reduction activity was found to depend upon the strength of the buffer used, which was optimal at 100 mM potassium phosphate and pH 7.6. The extinction coefficient of DPPH was $4.09\;mM^{-1}\;cm^{-1}$. DPPH reduction followed classical Michaelis-Menten kinetics ($K_m\;=\;28\;{\mu}M$, $K_{cat}\;=\;1690\;min^{-1}$). This method uses readily available materials, and has the additional advantages of being rapid and inexpensive.

• 한국주조공학회지
• /
• 제22권3호
• /
• pp.130-136
• /
• 2002

The growing use of aluminum for castings over the past decade has brought with it the increased scrutiny of component properties. One area that has received much attention is the effect of in inclusions - or impurities particles held in the metal - on casting properties. A new method of electromagnetic separation for removal of inclusions in aluminum alloy melts is proposed. The principle is that as the electromagnetic force induced in metal acts on inclusions due to low electric conductivity, they are moved to the direction opposite to electromagnetic force and can be separated and removed from the melt. Experiments were carried out on A356 melt mixed alumina particles and commercial Al alloys of ADC 10 and 12. In the experiment using A356, it was proved that $Al_2O_3$ particles was separated and removed continuously from matrix melt by electromagnetic force. Based on these results, the continuous separation experiment that used ADC 10, 12 was carried and the cleanliness of melt was assessed by the amount of porosity, hydrogen contents, PoDFA and mechanical properties through tensile test. As the results of analyses, the amount of porosity and hydrogen contents decreased without variation of chemical composition in the specimen that passed the electromagnetic continuous separator. In addition, tensile strength and elongation of this specimen increased by $20{\sim}30%$ because of reduction of inclusions.