• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.1033-1036
• /
• 2005

The effect of surface roughness on the contact fatigue was investigated in this study. To accomplish this goal, contact analysis based on the influence functions and the rectangular patch solution was performed to obtain the subsurface stress. Mesoscopic multiaxial fatigue criterion is then applied to predict fatigue damage. Suitable counting method and damage rule were used to evaluate the fatigue life of random loading caused by rough surface. As a result of the analysis, relationship between the life and roughness as well as the creack initiation depth was revealed. Below the critical roughness, It is observed that the fatigue life has hardly changed and creack is initiated around the depth at which the maximum shear stress occurs. Different behavior, however, is observed in case that the roughness is above the critical value.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.8
• /
• pp.849-855
• /
• 2008

An experimental method based on contact resonance is developed to extract the contact parameters of mechanical joints under various clamped conditions. Mechanical joint parameters of shear contact stiffness and damping were extracted for different physical joint parameters such as surface finish of the mating surfaces, the presence of lubrication, the effect of the clamping pressure, and shear load. It was found that the shear contact stiffness values decreased with increasing clamping load and increased with increasing shear loading. Contact damping ratio values were almost constant with clamping load, but decreased with increasing shear load. Moreover, rough surfaces exhibited the highest shear stiffness and contact damping compared to smooth surfaces.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.4
• /
• pp.249-261
• /
• 1997

A basic study on the lifting lug design has performed through the rational and systematic process. In order to evaluate the proper design-load distribution around lug eye investigation of contact force between lifting lug and shackle pin is performed using non-linear parametric analysis idealized by gap element models. Gap element modeling and nonlinear analysis procedures are illustrated and discussed based on MSC/NASTRAN. Some analysis and design guides are suggested through the consideration of several important effects such as stress distribution pattern, circumferential contact force distribution along the lug eye face, loading share rate between lug main plate and doubler, effect of loading direction, relation between applied force and deflection and size effect of shackle pin radius. Additionally optimum design studies are performed and general trends according to the variation of design parameters are suggested.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.399-405
• /
• 2014

Porous alumina with different porosities, 5.2 - 47.5%, were coated with cover-glass having a thickness of $160{\mu}m$, using epoxy adhesive. We investigated the effect of the porosity of the substrate layer on the crack initiation load, and the size of cracks propagated in the coating layer. Hertzian indentations were used to evaluate the damage behavior under a constrained loading condition. Typically, two types of cracks, ring cracks and radial cracks, were observed on the surface of the glass/porous alumina structure. Indentation stress-strain curves, crack initiation loads, crack propagation sizes, and flexural strengths were investigated as a function of porosities. The results indicated that a porosity of less than 30% and a higher substrate elastic modulus were beneficial at suppressing cracks occurrence and propagation. We expect lightweight mechanical components with high strength can be successfully fabricated by coating and controlling porosities in the substrate layer.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.23 no.1
• /
• pp.69-78
• /
• 2007

This study was performed to compare the stress distribution pattern in the crestal cortical bone and cancellous bone using 3-dimensional finite element stress analysis when 2 different Young's modulus(high modulus, model 1; low modulus, model 2) of cancellous bone was assumed. For the analysis, a finite element model was designed to have two square-threaded implants fused together and located at first and second molar area. Stress distribution was observed when vertical load of 200N was applied at several points on the occlusal surfaces of the implants, including central fossa, points 1.5mm, 2mm, 3mm and 3.5mm buccally away from central fossa. The results were as follows; 1. In both model, the maximum Von-Mises stress in the crestal cortical bone was greater when the load was applied at the central point, points 1.5mm and 2mm buccally away from central fossa than other cases. 2. In the cortical bone around first and second molar, model 2 showed greater Von-Mises stress than model 1. It is concluded that when the occlusal contact is afforded, the distribution of stress varies depending on the density of cancellous bone and the location of loading. More favorable stress distribution is expected when the contact load is applied within the diameter of fixtures.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.779-784
• /
• 2014

This study provided the analytical model describing the friction-induced noise in the ball joint system under the edge loading condition. The frictional and conformal contact kinematics between the spherical bearing and the hemispherical socket was derived and the dynamic equations of the perturbed motion were established. The numerical results revealed that the bending modes of the ball joint system can become unstable due to friction, and the axial load and contact stiffness strongly influenced the dynamic instability. In contrast, the tilting angle of the socket was not found to significantly contribute to the dynamic instability of the ball joint.

• International Journal of Concrete Structures and Materials
• /
• v.1 no.1
• /
• pp.29-36
• /
• 2007

The purpose of this paper is the assessment of the capacity of the reinforced concrete (RC) elements of an arch bridge when they are subjected to contact and near-contact explosive charges of various amounts, and the estimation of the critical charges for these components. The bridge considered is the Tenza Viaduct, a decommissioned structure south of Naples, Italy. Its primary elements, deck, piers and arches were analyzed. The evaluation was accomplished via numerical analyses that made possible to obtain the elements dynamic response when they are exposed to blast loading conditions. To evaluate the member's capacities, failure criteria for deck, piers and arches were proposed based on concrete damage parameters. Additionally, curves relating the explosive charge to the residual capacity and to damage level of the elements were also developed. The results of this work were taken into account to investigate the progressive collapse of the global structure.

• Tribology and Lubricants
• /
• v.28 no.5
• /
• pp.203-211
• /
• 2012

Atomic force microscopy (AFM) has been used as a tool, not only for imaging surfaces, but also for measuring surface forces and mechanical properties at the nano-scale. Force calibration is crucial for quantitatively measuring the forces that act between the AFM probe of a force sensing cantilever and a sample. In this work, the lateral force calibrations of a V-shaped cantilever were performed using the finite element method, multiple pivot loading, and thermal noise methods. As a result, it was shown that the multiple pivot loading method was appropriate for the lateral force calibration of a V-shaped cantilever. Further, through crosschecking of the abovementioned methods, it was concluded that the thermal noise method could be used for determining the lateral spring constants as long as the lateral deflection sensitivity was accurately determined. To obtain the lateral deflection sensitivity from the sticking portion of the friction loop, the contact stiffness should be taken into account.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1352-1358
• /
• 2004

The mechanical spring is one of widely used machine elements. Among various kinds, flat-type spring loaded by a rotating pin was studied. A flat spring was simplified to a cantilever beam, and numerical analysis was attempted. Since the loading pin rotates about a separate axis from the fixed spring or vice versa, the location, direction, and magnitude of the contact force including normal contact and friction loads vary accordingly. Meanwhile, the spring is deformed substantially as the relative motion progresses. Therefore, this problem needs to be formulated taking the follower loading characteristics and geometrical non-linearity into account. Derived nonlinear differential equation was solved to yield the spring deflection, contact force and the torque to rotate the pin, and the result was compared with a finite element solution. Also, the influences of principal design parameters were studied. The proposed methodology is expected to be useful for the design of pin-loaded flat spring and the prevention of mechanical failures in the form of yielding or fatigue failure of spring or severe wear of the components.

• Journal of the Korean Ceramic Society
• /
• v.45 no.4
• /
• pp.238-244
• /
• 2008

Modeling and FEM analysis on Boron Nitride and/or Pyrolytic Carbon coating layers on SiC fibers under indentation contact loadings are investigated. Especially this study attempts to model the mechanical behavior of the SiC fibers with and without coatings. Tyranno S grade and Tyranno LoxM grade of SiC are selected for fiber and Boron Nitride and/or Pyrolytic Carbon as coating material. The modeling is performed by SiC fiber without coating layer, which includs single(BN or PyC) and double(BN-PyC or PyC-BN) coating layer. And then the analysis is performed by changing a type of coating layer, a type of fiber and coating sequence. In this study, the concepts of modeling and analysis techniques for optimum design of BN and PyC coating process on SiC fiber are shown. Results show that stresses are reduced when indentation contact loading applies on the material having lower elastic modulus.