• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1918-1923
• /
• 2010

In electic railway, 25kV is applied to AC sections of overhead contact lines and pantographs of Korea Train eXpress(KTX) make contact at speeds of 300km/h. Thus, there is a need to utilize wireless, optic, contact-less sensors to implement condition monitoring systems. This paper is based on describing and analyzing the condition monitoring system implementation technologies for efficient catenary current ratio characteristic assessment. The conclusion of this paper should be widely applied to design, diagnosis, completion of construction, current collection status, fault diagnosis, and selection of contact wires and suspension wires.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 하계학술대회 논문집
• /
• pp.261-264
• /
• 1990

The specific contact resistance(SCR) of metal-semiconductor interface is an important design parameter for VLSI interconnecting technology. As the critical feature size of the integrated structures decrease, the physical size of ohmic contacts will also decrease and the series contact resistance will increase. Al-Si contacts on the annealing condition are studied. The propreties of the contacts depend considerably on the annealing procedures. Barrier height is measured from Capacitance-Voltage characteristics. The specific contact resistance are analyzed using a modified four point method.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.13-18
• /
• 2001

In this paper, FFT(Fast Fourier Transform) analysis of friction was suggested as a method to interpret the contact conditions. Micro-grooves with various dimensions were fabricated on the silicon surface to investigate the frictional behavior with respect to the change in geometrical contact condition. Frictional forces between micro-grooved surfaces and spheres modeled as surface asperities were measured using a micro-tribotester which was built inside a SEM(Scanning Electron Microscope). The experimental results show that the relative dimensions and distributions of contact asperities between two surfaces can be predicted by the power spectrum and the main frequency in FFT-based analysis of friction coefficient. Also, it was shown that the friction coefficient for multi-asperities was the result of the superposition of that for each asperity.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.450-455
• /
• 2004

There is few research about contact problem for a rigid surface with an arbitrary shape in SPH. The variational equation based on the virtual work principle is derived and its solution is obtained by the penalty method. It is proposed a new method that can determine the parameters for a penetration and a penetration rate used in the penalty method. The reproducing condition is adopted to correct the deficiency of kernel on the boundary. In order to calculate a penetration of particles, after checking boundary particles for deformable body boundary normal vectors were determined on the rigid surface. Numerical simulations for models which have rigid surface with an arbitrary shape were conducted to validate the proposed method in 2D. The results of those analysis represent that the contact algorithm proposed in this study works properly.

• 대한기계학회논문집A
• /
• 제29권1호
• /
• pp.30-37
• /
• 2005

There is few research about contact problem for a rigid surface with an arbitrary shape in SPH. The variational equation based on the virtual work principle is derived and its solution is obtained by the penalty method. It is proposed a new method that can determine the parameters for a penetration and a penetration rate used in the penalty method. The reproducing condition is adopted to correct the deficiency of kernel on the boundary. In order to calculate a penetration of particles, after checking boundary particles for deformable body, boundary normal vectors were determined on the rigid surface. Numerical simulations for models which have rigid surface with an arbitrary shape were conducted to validate the proposed method in 2D Cartesian and cylindrical coordinate. The results of those analysis represent that the contact algorithm proposed in this study works properly.

• Tribology and Lubricants
• /
• 제25권4호
• /
• pp.231-235
• /
• 2009

In this study, the influence of contact pressure on the variation in coefficients of friction between porcine knee joint cartilage and Co-Cr alloy in a repeat pass sliding motion was investigated. Flat-ended cartilage pin specimens(9 mm diameter, 8 mm long) were prepared from porcine(6 months old) knee joints by a drill-type punch. Friction tests were conducted by using a pin-on-disk type friction tester for an hour in PBS lubricated condition under the contact pressures of 0.5, 1 and 2 MPa with 50 mm distance per a cycle at ambient condition. As a result, coefficients of friction increased as the test duration increased for all contact pressures. The maximum coefficients of friction were 0.082, 0.06 and 0.098 for 0.5, 1, and 2 MPa, respectively. It showed that coefficients of friction of porcine knee joint cartilage against Co-Cr alloy depended on the level of contact pressure and related to squeeze film lubrication mechanism.

• 한국안광학회지
• /
• 제10권4호
• /
• pp.313-321
• /
• 2005

소프트 콘택트렌즈에서의 미생물 오염에 의한 정도를 알아보기 위해 각기 다른 방법의 2가지 실험이 실시되었다. 첫 번째 실험에서는, 소프트 콘택트렌즈 착용 시 각막염의 주된 원인균이 될 수 있는 Staphylococcus aureus, Pseudomonas aeruginosa 그리고 Enterobacter aerogenes의 현탁액을 이용하여 소프트 콘택트렌즈를 오염시킨 후, 렌즈표면을 주사전자현미경으로 관찰하였다. S. aureus로 소프트 콘택트렌즈를 오염시킨 지 1시간 경과 후에 다수의 세균이 렌즈에 유착되어 있는 것이 관찰되었으며, 시간의 경과(2, 4, 6, 12, 그리고 24 시간)에 따라 오염양상은 더욱 증가하였다. P. aeruginosa의 경우, 12시간 경과 후에 세균이 렌즈에 유착되어 있는 것이 관찰되었으며 또한, E. aerogenes는 24시간 경과 후에 세균이 렌즈에 유착되어 있었으며 무정형의 물질이 렌즈 표면 일부에서 관찰되었다. 두 번째 실험에서는, 안질환이 없는 20대 남녀 21명을 대상으로 소프트 콘택트렌즈를 4시간 착용시켜 봄으로써 소프트 콘택트렌즈에서의 미생물 오염양상 정도를 살펴보았다. 그 결과 다수의 세균류와 진균류가 관찰되었으며, 특히 세균류는 균의 색과 콜로니의 형태로 판별하여 단일종, 2종, 그리고 3종이 렌즈에 유착되어 있는 것이 관찰되었다.

• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1658-1667
• /
• 1993

In this research, a numerical algorithm has been developed, which can be applied to the large deformation and large displacement contact problems between two deformable bodies. The contact conditions expressed in terms of the rate of angle change have been proposed considering the change in geometric shape and rate of contact force. A set of linear simultaneous equations is constructed by adding the geometric shape change and contact conditions to the original stiffness matrix. A new method to determine time increment has been proposed based on Euler method, in which the condition to prevent the contact bodies from penetrating and overrunning each other has been taken into consideration. Practical application to contact problem is extrusion in which bodies are sliding along the contact boundary.

• 지질공학
• /
• 제8권3호
• /
• pp.215-224
• /
• 1998

LVDT에 의해 전체변형율이 측정되었고, 국부적 변형율은 변형율게이지에 의해 측정되었다. 또한 공시체에서의 응력 분포를 알기 위하여 유한요소법에 의한 축대칭 탄소성 해석을 하였다. 단면구속영향을 고려하면 H/D=1인 경우에 특히 구속영향을 크게 받는다. 또한 공시체 직경에 대한 공시체 길이가 길어질수록 영향을 적게 받는다는 것을 알 수 있다. 공시체와 재하판과의 접촉면에서 응력 및 변위 분포는 접촉하고 있는 두 재료의 탄성계수비와 접촉면의 마찰저항에 크게 좌우된다. 즉 암석공시체에 대한 재하판의 영향은 경암에서보다 연암에서 더 현저하다 또한 단면구속이 변형율 분포에 미치는 영향 및 치수효과는 강성이 큰 암석에서 현저하게 나타난다.

• 한국안전학회지
• /
• 제32권1호
• /
• pp.15-20
• /
• 2017

A large amount of research has been performed on the rolling contact fatigue(RCF) life of bearings, since it directly affects the safety and reliability of mechanical systems. It is well known that rolling contact fatigue life is influenced by several parameters including contact pressure, oil contamination by water or metal particles, and the surface conditions of bearings. However, the detailed damage mechanisms involved in rolling contact fatigue have not been clearly identified yet. In this paper the effects of water contamination of the lubricant and surface roughness of bearing steel on the rolling contact fatigue life were investigated. Two types of specimens with different surface roughness values were prepared through turning and lapping operations. They were tested under two different lubrication conditions, i.e. oil lubricant with 100% of oil and the water contaminated condition with 80% of oil and 20% of water using the rolling contact fatigue testing machine. The surface damage induced by the rolling contact fatigue was observed by using atomic force microscope(AFM). Experimental results show that the rolling contact fatigue life, $L_{10}$ was reduced by 24 to 33% depending on the lubrication condition. The reduction of fatigue life in the range of 53 to 57% was also observed at different surface roughness conditions.