• KSTLE International Journal
• /
• 제1권1호
• /
• pp.63-68
• /
• 2000

Angular contact ball bearings are mainly used in the spindle, which requires high speed and stiffness. The heat generation is studied by experiments and simulations using a pair of angular contact ball bearings. The temperature variation of inner and outer races and the temperature increment distribution are measured by using thermocouples for the rotational speed, preload, viscosity of lubricant. The measured values from experiments are used to estimate the heat conduction rate. The method of oil-air lubrication is used for the experiment. The amount of conduction heat transfer to the test spindle and the convection heat transfer coefficients long the spindle are computed by using inverse method with temperature increment distribution. Total heat generation rate is estimated with the heat partition rate which is calculated from temperatures of inner and outer races. In addition, the empirical factor of oil-air lubrication method for Palmgren's heat generation model is suggested. The empirical friction coefficients, which are obtained from the experiments, depend on the preload condition, and can give us more accurate estimation of the heat generation in ball bearings.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권2호
• /
• pp.136-143
• /
• 1995

With the contact angle of phase dropping epoxy resin on the inorganic filler(glass plate) surface treated with air plasma, we have studied about the interfacial wettability between epoxy resin and glass plate as a simple model of glass fiber reinforced composite materials. The contact angle on the inorganic filler surface varied with surface treatment conditions. The contact angle significantly depends on plasma treating time and environment temperature in the oven. From the view point of plasma treatment condition in this work, when discharge conditions were pressure 200mtorr, voltage 800V, magnetic flux density 8OGauss, optimum treatment time were proved as 3,4 and 5 minutes for the environment of >$80^{\circ}C$, >$100^{\circ}C$ and >$120^{\circ}C$, respectively.

• 소성∙가공
• /
• 제20권5호
• /
• pp.344-349
• /
• 2011

Variation of contact pressure causes change of friction coefficient, which in turn changes stress distribution in the sheet being formed and final springback. In the present study, U-draw bending experiments were carried out under constant blank holding force(BHF) and different blank sizes, and finite element analysis was conducted with and without considering contact pressure effect on friction. When the BHF was sufficiently high, the degree of springback was different between constant blank holding pressure condition and that with varying blank holding pressure. Finite element analysis considering the influence of contact pressure effect on friction could explain the occurrence of springback.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.71-74
• /
• 2000

In this study, the optimal condition of surface treatment for aluminum panel was determined by measuring the contact angle and T-peel strength. The contact angle was measured for various mixture ratios of acetylene gas and nitrogen gas. The mixture (acetylene gas to nitrogen gas) ratios used were 1:9, 3:7, 5:5, 7:3, and 9:1. The contact angle was also measured as a function of time of surface treatment. The results showed that the contact angle was a minimum for mixture ratio of 5:5. T-peel strength was a maximum for the treatment time of 30 second.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.950-955
• /
• 2004

Slip displacement is brought into focus to study the tube fretting wear that occurs on the contact by the springs. An oscillating tube was in contact with plate support springs. The contact condition was varied as normal force 5 N, and gaps of 0.1 and 0.2 mm in the experiment. The oscillation range of the tube was also varied as 0.2, 0.3, 0.4 and 0.7 mm. Formulas for predicting the slip displacement range were derived in terms of the vibration amplitudes measured during the tube oscillation. It was found that the slip displacement in transverse direction was much higher ($720{\sim}33000$ times) than that in axial one. This resulted in the severer wear on the contact suffered from transverse slip.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 춘계학술대회 논문집
• /
• pp.590-596
• /
• 2002

Contact wires are made by metallic materials and exposured at atmosphere. We have investigated mechanical properties and the present condition of air pollution as to the messenger wires and ACSR wires of these contact wires. Mechanical properties between new contact wires and used, the used one's tensile strength and elongations was decreased by effect from corrosion. We observed a fatigue properties which was investigated by fatigue test because contact wires were affected with amplitude vibration everytime the train passed through the railways. In the evaluation of fatigue test, it was also shown that fatigue life of the used wires was decreased 50 ∼ 60% compared with that of new ones in average by effect from corrosion.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.724-729
• /
• 2005

Winter weather condition can cause icing and ice coats on 25 kV overhead contact wire. This generates shocks at the mechanical interface of the collecting strips of the pantograph and the contact wire and extra electrical resistance, which may affect quality of current collection at the contact wire / collecting strips of pantograph interface. De-icing operations should he performed just before train operation to avoid the formation of another ice layer. Thus, the work in this paper is investigation and analysis of de-icing system which could be applied to the electric car line of railways.

• 한국철도학회논문집
• /
• 제12권2호
• /
• pp.236-242
• /
• 2009

본 연구에서는 철도차량의 차륜과 레일에 대해 플랜지 접촉을 포함하여 모든 위치예서 차륜-레일간 접촉 위치를 수치 해석적으로 구하는 방범을 제안한다. 이를 위해 차륜과 레일의 형상은 매개변수로 표현되는 3차원 곡면함수로 나타내었다. 기구학적 구속조건식을 Newton-Rhapson 방법을 이용하여 구하는 것과 차륜과 레일간 최소거리가 0이 된다는 최적화 방법을 동시에 이용하여 정확하고 효율적으로 계산하는 새로운 방법을 제안하였다.

• 한국전기전자재료학회논문지
• /
• 제23권1호
• /
• pp.10-13
• /
• 2010

The plasma processing technologies of thin film deposition and surface treatment technique have been applied to many industrial fields. This study is purposed Large-area uniformity and surface treatment on the stainless substrate. We treat surface of stainless by $CF_4$ plasma. $CF_4$ plasma is generated by using SPM(Scanning plasma method)which is kind a of CVD. Generally, SPM has been used for uniform surface treatment using a crossed electromagnetic field. The optimum discharge condition has been studied for the gas pressure, the magnetic flux density and the distance between substrate and electrodes. In result, contact angle is increased by surface treatment using $CF_4$ Plasma. Therefore we expect that SPM to control contact angle is applied to many industries.

• Journal of Welding and Joining
• /
• 제22권1호
• /
• pp.43-49
• /
• 2004

Contact tip is located so near to welding arc that it is heated to high temperature during long time welding. In such a situation, tip changes in its microstructure and in turn its mechanical properties. This study was intended to investigate those changes by using simulated heat treatment. As a result of this study, it was confirmed that tip of Cu-P alloy hardened with severe cold deformation lose its initial hardness to a large extent within 60 min due to the occurrence of rapid recrystallization while that of Cu-Cr composition hardened by proper aging treatment can preserve its intial hardness for about 1,000 min or longer. Based on these results, suggested was a guideline that can classify contact tips into two different grades: deformation-hardened type and precipitation-hardened type. Following a guideline, a tip with Cu-Cr composition can be classified into the deformation-hardened type if it is in the over-aged condition. Such a guideline is well described.