• Journal of Acupuncture Research
• /
• 제19권3호
• /
• pp.64-76
• /
• 2002

Objective : The purpose of this study is to investigate the mechanism and effect of moxibustion objectively and to be used as the quantitative data for developing the new thermal stimulating treatment by observing the combustion characteristics of commercial moxaes. Methods : We have selected two types(large-size moxa A(LMA), large-size moxa B(LMB)) among large moxaes used widely in the clinic. We examined combustion times, temperatures, temperature gradients in each period during a combustion of moxa. Results : 1. The ascending temperature gradient measured in the central point of non-contacted surface was fastest, the average ascending temperature gradient of both moxaes was $0.0384^{\circ}C/sec$, $0.0123^{\circ}C/sec$ respectively, 3.1 times faster in LMA. The maximum ascending temperature gradient was also about 2.9 times faster in LMA. The time required for the maximum ascending temperature gradient from ignition was 254sec, 411sec respectively. 2. The minimum descending temperature gradient in the retaining period was $-0.0250^{\circ}C/sec$, $-0.0090^{\circ}C/sec$ respectively and the average descending temperature gradient was $-0.0160^{\circ}C/sec$, $-0.0037^{\circ}C/sec$ respectively on the non-contact surface. 3. On the basis of the non-contact surface($A_I$), the time at which the effective stimulus period began to occur was about 264sec, 796sec respectively after an ignition, the time at which the maximum temperature began to occur was about 373sec, 1323sec respectively after an ignition, and the maximum temperature was $0.9^{\circ}C$ higher in LMA. The maximum ascending temperature gradient was also about 4.2 times faster in LMA. Conclusion : It was thought that not only the figure of moxicombustion device, but also the form and size of moxa had influence on the combustion characteristics deciding the performance of stimulus seriously.

• 한국의류산업학회지
• /
• 제21권3호
• /
• pp.336-345
• /
• 2019

This study evaluated the preference and wearing characteristics of existing fitness compression wear for elderly women and identified the problems and improvements of existing fitness apparel. Preference and wearing characteristics for 6 types (A-F) of upper and lower fitness compression wear were evaluated. Photos and drawings as well as the preferred designs and details were investigated after presenting the evaluation clothing. Evaluations were made on a 5 point Likert scale for the fitness, allowance, pressure, ease of movement, fabric material, and overall satisfaction after wearing. The design preference indicated that B type (26.6%) and C type (23.4%) were preferred in the top with C, E and F type preferred to the same ratio of 19.4% in the slacks. The fitness and allowance amount of the top B type were the most appropriate (${\geq}4$), the C type was in close contact (2.86), and the F type was inadequate in the neck circumference (1.77). The feeling of pressure was high in the waist, abdomen, thighs, and knees. The area where the elderly people want to improve their strength was the legs; in addition, a pattern design was needed to strengthen leg muscles when designing fitness compression wear. However, a design with excessive adhesion due to a muscle support band was shown to be not preferred. Therefore, depending on the activity, it is necessary to develop a fitness compression wear that applies an optimum stretching ratio of fabric based on body surface area changes.

• Bulletin of the Korean Chemical Society
• /
• 제28권10호
• /
• pp.1661-1664
• /
• 2007

Direct reaction of elemental silicon with a gaseous mixture of isopropyl chloride (1) and hydrogen chloride in the presence of copper catalyst using a stirred bed reactor equipped with a spiral band agitator gave isopropyldichlorosilane having a Si-H bond (2a) as a major product and isopropyltrichlorosilane (2b) along with chlorosilanes, trichlorosilane and tetrachlorosilane. A process for production of 2a was maximized using the 1:0.5 mole ratio of 1 to HCl and smaller size of elemental silicon at a reaction temperature of 220 °C. When a reaction was carried out by feeding a gaseous mixture of 1 [12.9 g/h (0.164 mol/h)] and HCl [2.98 g/h (0.082 mol/h)] to a contact mixture of elemental silicon (360 g) and copper (40 g) under the optimum condition for 45 h, 2a among volatile products kept up about 82 mol % until 35 h and then slowly decreased down 68 mol % in 45 h reaction. Finally 2a was obtained in 38% isolated yield (based on 1 used) with an 85% consumption of elemental silicon in a 45 h reaction. In addition to 2a, 2b was obtained as minor product along with chlorosilanes, trichlorosilane, and tetrachlorosilane. The decomposition of 1 was suppressed and the production of 2a improved by adding HCl to 1.

• Journal of the Korean Wood Science and Technology
• /
• 제20권1호
• /
• pp.15-22
• /
• 1992

This study was performed to investigate the corrosion of metal fasteners in waterborne preservative-treated wood. Of all the metal tested, steel exhibited the greatest amount of corrosion across all preservatives and exposure conditions whereas stainless steel was totally inert. Galvanized steel corroded at a much lower rate compared to steel and the corrosion of brass was negligible. Among the preservatives, CCA-Type B was the most corrosive system tested. The sequence for the average corrosivity across all metals was: CCA-type B>CCA-Type C${\geq}$ACC${\geq}$CCA-Type A. Across all metals and retentions the salt formulations were more corrosive than the oxide and the corrosion was increased with the increse in the amount of preservative loadings. The amount of corrosion was also increased with the increase in exposure relative humidity (RH) across all metals and presevatives However, at the 60% RH exposure condition, the corrosion of metals was very negligible. Consequently, it can be concluded that across all metals oxide-type preservatives should be used to prevent the corrosion problem of metal fasteners in contact with treated wood and the use of steel nail preservative-treated wood should be avoided without distinction of end-use location, i.e., exterior or interior, and the use of stainless steel or at least brass nail in damp exterior condition was strongly recommended.

• Journal of the Optical Society of Korea
• /
• 제9권4호
• /
• pp.135-139
• /
• 2005

We demonstrate a simple and effective wavelength-tunable add/drop filter suitable for coarse wavelength division multiplexing (CWDM) systems. The filter consists of two fibers in contact side by side, with identical long-period fiber gratings (LPG) in each fiber. The LPG couples the power in the fundamental core mode to one of the cladding modes, which is then coupled to the same order cladding mode in the other fiber through evanescent-field coupling between two fibers. Finally, the cladding mode in the second fiber is coupled to its core mode with the help of the other LPG. With an optimal longitudinal offset distance of 10 em, coupling efficiency as high as -1.68 dB and side lobes smaller than -24 dB were experimentally obtained. The experimental results agreed well with the theoretical ones. The operating wavelength of the proposed add/drop filter was tunable by varying the temperature. The temperature sensitivity was measured to be -0.43 nm/$^{\circ}C$.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.338-341
• /
• 2009

In this paper, three-dimensional finite element approach to determining the number of blows in hammer forging is presented. Energy efficiency which is a major factor affecting the number of blows in hammer forging is assumed to decrease linearly as die-material contact area increases. The approach is applied to predicting the number of blows in counterblow hammer forging of large crank shaft for medium sized ship engine.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.384.2-384.2
• /
• 2016

Recent publications reported the self-propelled jumping of coalescing dew droplets on superhydrophobic surfaces [1-2]. We further investigated the initial growth, coalescence, and removal by self-propelled ejection of nano and microscopic water droplets on the superhydrophobic surface of lotus leaves under condensing conditions. By using a high-speed digital camera mounted on an optical microscope, we have found: (1) sub-micrometer droplets form and grow on nanoscale waxy hairs; (2) growing droplets coalesce rapidly upon contact, but never jump off the surface unless the diameter of merged droplets exceeds ${\sim}15{\mu}m$; (3) the diameter and direction of jumping droplets are very narrowly distributed, centered at $20-30{\mu}m$ and ${\sim}20$ degrees from the surface normal, respectively. We present a rationale for these observations on the basis of: (a) the hierarchically rough surface structure on nano- and micro-scales; (b) its chemical composition; and (c) the balance among competing forces of cohesion (surface tension), adhesion and gravity.

• 대한전기학회논문지
• /
• 제32권7호
• /
• pp.234-238
• /
• 1983

이 논문은 단일 전하로 전달되는 이중(금속-반도체-금속) 접착 소자에서 일차원적인 수송 방정식을 정상 상태에서 마이크로 컴퓨터로 해를 구하였다. 수송방정식을 해석적으로 풀이 하기 위해 일반적으로 행하여왔던 대부분의 가정과 개략치는 본 논문에서는 배제하였다. 결과는 에너지 상태, 밀도상태, 전류-전압 특성등에 관하여 중점을 두엇다. 인가 전압의 함수로 나타낸 미분 정전 용얄의 컴퓨터에 의한 해를 제시히고 영상전하 효과로 수정법도 제시 하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1446-1449
• /
• 2005

The purpose of this study is the real-time shape measurement of three-dimensional object by using color coded information. The paper relates to non-contact optical measurements of surface profiles or displacements, because of optical measurement systems are advantageous over using mechanical sensing, their relatively high speed and non-destructive capabilities. Therefore is particularly useful for three dimensional sensing which requires high horizontal and vertical resolution of measurements over a wide range thereof. Each a red, blue, green by using a inherence colors of hue value are good point.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1473-1474
• /
• 2011

박막트랜지스터(Thin Film Transistor: TFT)의 게이트 절연층 에서는 박막의 전계강도, 고유전율 및 우수한 표면 특성이 요구된다. HD-PECVD(High Density - Plasma Enhanced Chemical Vapor Deposition)를 이용하여 $NH_3$ 유량 및 기판 온도를 변화시키면서 SiN 박막을 제작하고, 표면특성을 AFM 으로, CONTACT ANGLE로 접촉각을 측정하여 Young's Equation 으로 Surface Energy를 계산하였고 전기적 특성은 MIM 구조를 제작하고 C-V 측정을 하여 조사하였다.