• Transactions on Electrical and Electronic Materials
• /
• v.17 no.4
• /
• pp.183-188
• /
• 2016

This paper presents the design and characterization of wide band ohmic microswitch with an actuation voltage as low as 20~25 V, and a restoring force of 14.1 μN. The design of the proposed switch is primarily composed of an electrostatic actuator, bridge membrane, cantilever (beam) and coplanar waveguide, suspended over the substrate. The analysis shows an insertion loss of −0.002 dB at 1GHz and remains as low as −0.35 dB, even at 100 GHz. The isolation loss of the switch is sustained at −21.09 dB at 100GHz, with a peak value of −99.58 dB at 1 GHz and up-state capacitance of 4 fF. To our knowledge, this is the first demonstration of a series contact switch, which works over a wide bandwidth (DC-100 GHz) and with such a high and sustained isolation, even at high frequencies and with an excellent figure of merit (f_c=1/2.pi.Ron.Cu= 39.7 THz).

• Journal of Korean Ophthalmic Optics Society
• /
• v.8 no.2
• /
• pp.119-127
• /
• 2003

We measured the effect of wettability of six MPSs for RGP lens. The used MPSs(multipurpose solutions) were OPTI-SOAK(ALCON), SOLO care hard(CIBA Vision), Total care(ALLERGAN), Simplicity(BOSTON). Wetting and Soaking Sol.(Bausch & Lomb) and Aquas-multi(Saehan). These MPSs keeps hydrophilic property of lens surface and increase the effect of cleaning or increase the effect of preservative effect. To compare with the effect of wettability we followed the way of contact angle measurement which was general way to measure wettability and compared lens which was conducted by each MPS made by different companies. As a control, 0.9% NaCl solution and artificial tears were used. The degree of the effect of wettability was decided by contact angle. It is hydrophilic property nearby $0^{\circ}$ of contact angle and it is closed by hydrophobic property as it increases. To compare with the effect of wettability we followed the way of contact angle measurement which was general way to measure wettability and compared lens which was conducted by each MPS made by different companies. As a control, 0.9% NaCl solution and artificial tears were used. The degree of the effect of wettability was decided by contact angle. It is hydrophilic property nearby $0^{\circ}$ of contact angle and it is closed by hydrophobic property as it increases. The results showed that every lens was nearby hydrophilic property within $25^{\circ}{\sim}36^{\circ}$. Also, it was differed by various factors. The surface tension showed various differences between 19.8 and 31.3(mN/m). In the viscosity, MPSs represented the highest viscosity between $4^{\circ}C$ and $20^{\circ}C$. It was much higher than compared with the viscosity of soft lens MPS. This experiment could be used to grasping the interaction between solutions used to MPS and the natural endowments of lens and to considering the relations of different factors effecting the wettability.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.1-8
• /
• 2011

5-axis NC machining has a good advantage of the accessibility of tool motion by adding two rotary axes. It offers numerous advantages such as expanding machining fields in parts of turbo machineries like impeller, propeller, turbine blade and rotor, reasonable tool employment and great reduction of the set-up process. However, as adding two rotary axes, it is difficult to choose suitable machining conditions in terms of cutter path and cutter posture at a cutter contact point. Therefore in this paper, it is proposed to decide suitable machining condition through an experimental method such as adopting various cutter paths, cutter postures types. Also, in order to increase the efficiency of 5-axis machining, it is necessary to minimize the cutter posture changes and create a continuous cutter path while avoiding interference. This study, by using an MC-space algorithm for interference avoidance and an MB-spline algorithm for continuous control, is intended to create a 5-axis machining cutter path with excellent surface quality and economic feasibility. finally, this study will verify the effectiveness of the suggested method through verification processing.

• Proceedings of the KOSOMBE Conference
• /
• v.1996 no.05
• /
• pp.22-26
• /
• 1996

In this paper, we designed 4-channel electrolyte analyzer that can measure simultaneousely the 4 electrolytes - pH, $pNa^{+}$, $pCa^{2+}$, and $pK^{+}-$ using 2-point calibration and implemented it. Developed electrolyte analyzer consists of singal processing part, actuator part and control unit for sample flow system. To implement reliable instrument, design considerations are emphasized on flow system and sample chamber that requires small sample volume and prevent air contact with sample solution. In addition to the hardware design, we developed system software which controls full measuring process. After system developed, we verified the system performance by the test measurement for pH, $pNa^{+}$, $pCa^{2+}$, and $pK^{+}$ value.

• Journal of the Korean Society of Tobacco Science
• /
• v.17 no.1
• /
• pp.68-78
• /
• 1995

A study of expanding tobacco includes the steps of adjusting the moisture content of cut tobacco, without the use of exogenous impregnants by contacting the filler with a high velocity gaseous medium at elevated temperature such that heat is rapidly and substantially uniformly transferred from the medium to the filler for a total contact time sufficient to expand the tobacco leaves. Study is disclosed for drying and expanding cut tobacco by introducing the tobacco into an elongated tubular shaped conduit through which steam high temperature 150-35$0^{\circ}C$ and high velocity above the 18m1sec, super steam is recycled. moisture content of shreded tobacco leaves, immediately before treatment within the range of from 10% to 24% and, most preferably, within the range of from 18% to 21%. Expanding rate showed 70% in NC -82(B.3) and 42% in Burley -21(B.1) which is produced in 1993 under this condition. When expanding tobacco expanded tobacco did not change significally, but they were decreased at 27$0^{\circ}C$ very largely. The curtailment of cost price and physical and chemical properties of various items were improved in cigarettes. Key words : Expanding tobacco, Super steam tobacco expansion, Fast drying tobacco, High temperature treat tobacco, Puffing tobacco.

• Korean Journal of Organic Agriculture
• /
• v.29 no.1
• /
• pp.1-23
• /
• 2021

The form of agri-food transaction has taken a rapid change from the existing method since Covid-19. In response to changes in the market environment such as Covid-19, the integrated marketing organization in Jeollabuk-do was diagnosed from the point of view of innovation, and the future direction was examined. In order to improve the distribution structure of the production area, an integrated marketing organization was fostered, and both quantitative and qualitative growth were brought about. However, some regions still lack willingness to participate and lack of expertise. In particular, there is no infrastructure and strategy to prepare for the increase in non-face-to-face transactions post Covid-19. Online transactions also require economies of scale, so non-face-to-face transaction capabilities must be reinforced by adding a separate organization and experts in charge of online transaction functions within the integrated marketing organization. In the future, online sales are highly likely to expand not only to transactions between producers and individual consumers (C to C), but also to mass consumer (B to B) transactions. It will be an opportunity. In addition, it is necessary to efficiently use production area distribution facilities such as sorting and packaging. Since the non-contact transaction method will increase after Corona 19, it is necessary to strengthen marketing capabilities such as expansion of utilization rate, order placement, settlement, and customer management, and reorganization of specialized organizations.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1543-1545
• /
• 1997

In this work, properties of FRP insulation materials by thermal-accelerated degradation were investigated. Usually, most degradations cause the hydrophilic to decrease the contact angle and surface properties. But, in this work on thermal-degradated FRP, we can confirm the introduction of hydrophobic properties by cross-linking and the ablation of small-molecules rather than chain scission and oxidation. Hydrophobic introduction in thermal-degradated FRP caused the increase of electrical insulation on treated FRP surface. But, Tensile strength decreased steeply on FRP being exposed higher temperature.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1546-1548
• /
• 1997

We investigated microhardness, friction, wear and wettability of polyimide for finding out the influence of ion implantation on surface properties. For increasing doses microhardness increased. A reduction of the friction coefficient was most cases correlated with a reduction of wear. The contact angles of water for $B^+$, $N^+$ implanted polyimide decreased from $76^{\circ}$ to zero, as the fluences increased energy of 50, 200 keV.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.217-224
• /
• 2000

This paper proposes a new type of HDD suspension integrated with shape memory alloy(SMA) actuator in order to prevent the friction between the slider and the disk. A finite element analysis is undertaken to investigate modal characteristics of the proposed self loading/unloading slider. The dynamic model is formulated and its validity is proved by comparing the predicted displacement transmissibility with the measured one. A control model is then established by integrating experimentally-obtained SMA actuator dynamics. Subsequently, a sliding mode controller is designed to achieve non-contact start/stop(Non CSS) modes, and control results are presented in time domain.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.908-913
• /
• 2000

CoSi$_2$/p+/n diodes(bilayer diodes) were fabricated by using epitaxial CoSi$_2$grown from Co/Ti bilayer as a diffusion source. The I-V characteristics of p+/n diodes were measured and compared with those of diode made from Co monolayer (monolayer diode). Monolayer diodes showed typical p+n junction characteristics with the leakage current of as low as 10$^{-12}$ A and forward current 6-orders higher than the leakage current, when drive-in annealed at 90$0^{\circ}C$ for 20 sec.. On the other hand, bilayer diodes showed the Schottky-like behaviors with forward currents rather higher than those of monolyer diodes, but with too high leakage currents, when drive-in annealed at $700^{\circ}C$ or higher. However, when the annealing temperature was lowered to $700^{\circ}C$ and annealing time was increased to 60 sec., the leakage current was reduced to 10$^{-11}$ A and thus sho3wed typical diode characteristics. The high leakage currents for diodes annealed at $700^{\circ}C$ or higher was attributed to Shannon contacts formed due to unremoved Co-Ti-Si precipitates. But when annealed at 50$0^{\circ}C$, B ions diffused in the direction of the surface layer, and thus the leakage currents were reduced by removing Shannon contacts.