• Membrane and Water Treatment
• /
• 제8권6호
• /
• pp.563-574
• /
• 2017

Antibacterial effective, high performanced, novel ZnO embedded composite membranes were obtained by blendig ZnO nanoparticles with polysulfone. IR, TG/DTG, XRD and SEM analysis were performed to characterize structure and morphology of ZnO nanoparticles and composite membranes. Contact angle, EWC, porosity and pore structure properties of composite membranes were investigated. Cross-flow filtration studies were performed to investigation of performances of prepared membranes. It was found from the cross section SEM images that ZnO nanoparticles dispersed homogenously up to additive amount of 2% and the membrane skin layer thicknesses increased in the presence of ZnO. Contact angle of pure PSf membranes were reduced from $70^{\circ}$ to $55^{\circ}$ after addition of 4% ZnO. Porosity of composite membrane contains 1% ZnO was higher about 22% than pure PSf membrane. BSA rejection ratio and PWF of 0.5% ZnO embedded composite membrane became 2.2 and 2.3 times higher than pure PSf membrane. It was determined from flux recovery ratios that ZnO additive increased the fouling resistance of composite membranes. Also, the bacterial killing ability of ZnO is well known and there are many researches related to this in the literature. Therefore, it is expected that prepared composite membranes will show antibacterial effect.

• 대한기계학회논문집A
• /
• 제21권12호
• /
• pp.2019-2028
• /
• 1997

It has been well established that resistant force and wear that occur during rolling motion depend on several factors such as material type, hardness, subsurface microstructure, applied load, and speed. The purpose of this work is to investigate the effect of microstructure and the state of deformed layer on the rolling contact characteristics in dry and lubricated rolling contacts. The results of this work show that the rolling resistance behavior depends on the state of the deformed layer. Also, lubrication can reduce the plastic flow at the surface but may still have an effect on the subsurface strain. The cross-sectional view of the microstructure shows that surface traction has a difinite effect on the morphology of the surface region. That is, significant slip seems to have taken place between the ball than those of the dry rolling case. The surface generation effects were significantly less compared to the case of dry rolling contact.

• 한국유체기계학회 논문집
• /
• 제17권2호
• /
• pp.30-34
• /
• 2014

Membrane distillation (MD) is a thermal driven separation process in which separation a hydrophobic membrane is a barrier for the liquid phase, letting the vapor phase pass through the membrane pores. Therefore, a porous and hydrophobic membrane should be used in membrane distillation. MD cannot work if water penetrates into the pores of the membrane (membrane wetting). Accordingly, it is necessary to prevent wetting of MD membranes and to remove water inside the pores of the wetted membranes if possible. In this context, our study aimed to develop methods to recover wetted membranes in MD processes. Poly-vinylidene fluoride (PVDF) membranes were used in this study. A laboratory-scale direct contact MD (DCMD) system was used to examine the effect of operating parameters on wetting. For dewetting the wetted membranes, specific techniques including the use of high temperature air were applied. The performances of the membranes before and after dewetting were compared in terms of flux, salt rejection and liquid entry pressure(LEP). The surface morphology of dewetted membrane was confirmed by scanning electron microscope (SEM).

• 전기학회논문지
• /
• 제63권5호
• /
• pp.671-675
• /
• 2014

This paper presents a fabrication of hydrophilic Poly(dimethylsiloxane) (PDMS) with periodic wrinkling surface. The proposed periodic wrinkling surface was fabricated using the sequential processes of typical curing process of PDMS, cutting process, platinum deposition process, and wrinkling transfer process. The surface morphology of the fabricated wrinkling surface was observed by using optical and dynamic atomic force microscopy and discussed. The measured period and amplitude of wrinkling was about $2.2{\mu}m$ and $0.31{\mu}m$, respectively. And, the contact angles of water droplets on the wrinkled surface were measured in order to understand effect of the wrinkling surface on surface modification of hydrophobic PDMS. Our new finding was that the proposed wrinkling surface was hydrophilic and the measured contact angle was about $62^{\circ}$. Moreover, it was found out from the simple cell culture test that the fabricated wrinkling surface was more effective for cell spreading and adhesion than the case of native PDMS substrate.

• 폴리머
• /
• 제32권5호
• /
• pp.497-500
• /
• 2008

폴리스틸렌발포체(스티로폼)를 비롯한 소수성 폴리머의 재활용과 친수성 표면개질의 한 방편으로 산소플라즈마 고정화와 그래프팅법을 이용하여 친수성인 아크릴산과 아크릴아미드단량체를 스티로폼 표면에 도입하였다. 플라즈마 처리에 의한 표면개질의 증거는 ESCA스펙트럼의 O/C와 N/C ratio의 증가, 전계방사현미경의 사진으로부터 박막생성 및 접촉각의 현저한 감소 현상의 관찰로부터 확인하였다. 접촉각은 $84^{\circ}$에서 $18{\sim}19^{\circ}$로 대폭 감소하였으며, 이는 아크릴산보다 아크릴아미드가 결정적 요인이 됨을 알 수 있었다.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.43-48
• /
• 2023

In this study, we investigate the tribological behavior of AISI 304 stainless steel pairs under deionized water and hexagonal boron nitride (h-BN) water dispersion lubrication. The specimen friction and wear properties are evaluated using a reciprocating ball-on-flat tribometer. The coefficient of friction remains nearly constant throughout the test under both lubricant conditions. The wear depth of the specimens under h-BN lubrication is smaller than that under deionized water lubrication, indicating the inhibition behavior of h-BN nanolubricants on direct metal-metal contacts. Optical micrographs and stylus profilometer measurements are performed to evaluate the severity of damage caused by the sliding motion and to determine the wear morphology of the specimens, respectively. The results show that h-BN nanolubricants does not have a significant effect on the friction behavior but demonstrates reduced wear owing to their trapping effect between the sliding interfaces. Moreover, scanning electron microscopy and energy-dispersive X-ray spectroscopy images of the specimens were acquired to confirm the trapping effect of h-BN between the sliding interfaces. The results also suggest that the trapped lubricants can distribute the contact pressure, reducing the wear damage caused by the metal-metal contact at the interface. In conclusion, h-BN nanolubricants have potential as an anti-wear additive for lubrication applications. Further investigation is needed to provide direct evidence of the trapping effect of h-BN nanoparticles between the sliding interfaces. These findings could lead to the development of more efficient and effective lubricants for various industrial applications.

• Tribology and Lubricants
• /
• 제40권3호
• /
• pp.71-77
• /
• 2024

Hydrogen has emerged as an eco-friendly and sustainable alternative to fossil fuels. However, the utilization of hydrogen requires high-pressure compression, storage, and transportation, which poses challenges to the durability of compressor components, particularly the diaphragm. This study aims to improve the durability of 304 stainless steel diaphragms in hydrogen compressors by optimizing their surface roughness and corrosion resistance through wet etching. The specimens were prepared by immersing 304 stainless steel in a mixture of sulfuric acid and hydrogen peroxide, followed by etching in hydrochloric acid for various durations. The surface morphology, roughness, and wettability of the etched specimens were characterized using optical microscopy, surface profilometry, and water contact angle measurements. The friction and wear characteristics were evaluated using reciprocating sliding tests. The results showed that increasing the etching time led to the development of micro/nanostructures on the surface, thereby increasing surface roughness and hydrophilicity. The friction coefficient initially decreased with increasing surface roughness owing to the reduced contact area but increased during long-term wear owing to the destruction and delamination of surface protrusions. HCl-30M exhibited the lowest average friction coefficient and a balance between the surface roughness and oxide film formation, resulting in improved wear resistance. These findings highlight the importance of controlling the surface roughness and oxide film formation through etching optimization to obtain a uniform and wear-resistant surface for the enhanced durability of 304 stainless steel diaphragms in hydrogen compressors.

• Tribology and Lubricants
• /
• 제40권3호
• /
• pp.84-90
• /
• 2024

This study investigates the effect of the surface microstructure on the tribological characteristics of glass substrates. Chemical etching using hydrofluoric acid and ammonium hydrogen fluoride was employed to create controlled asperity structures on glass surfaces. By varying the etching time from 10 to 50 min, different surface morphologies were obtained and characterized using optical microscopy, surface roughness measurements, and water contact angle analysis. Friction tests were performed using a stainless steel ball as the counter surface to evaluate the tribological behavior of the etched specimens. The results showed that the specimen etched for 20 min exhibited the lowest and most stable friction coefficient, which was attributed to the formation of a uniform and dense asperity structure that effectively reduced the stress concentration and wear at the contact interface. In contrast, specimens etched for shorter (10 min) or longer (30-50 min) durations displayed higher friction coefficients and accelerated wear owing to nonuniform asperity structures that led to local stress concentration. Optical microscopy of the wear tracks further confirmed the superior wear resistance of the 20-minute etched specimen. These findings highlight the importance of optimizing the etching process parameters to achieve the desired surface morphology for enhanced tribological performance, suggesting the potential of chemical etching as a surface modification technique for various materials in tribological applications.

• Journal of Periodontal and Implant Science
• /
• 제48권5호
• /
• pp.326-333
• /
• 2018

Purpose: The present study investigated the outcomes of a newly-developed, simple, and practical nonsurgical treatment modality suitable for most forms of intrabony defects around failing dental implants using intrasulcular delivery of chlorhexidine solution and minocycline hydrochloride (HCl). Methods: Forty-five dental implants in 20 patients diagnosed with peri-implantitis were included. At baseline and the study endpoint, the probing pocket depth (PPD), clinical attachment level (CAL), and the presence of bleeding on probing (BOP) at 6 sites around each implant were recorded. The radiographic osseous defect morphology at the mesial or distal proximal aspect of each implant was classified as 1) narrow or wide and 2) shallow or deep. For a comparative analysis of bone changes according to the defect morphology, the distance from the implant shoulder to the most coronal bone-to-implant contact point (DIB) at the mesial and distal aspects of each implant was measured at baseline and the endpoint. Patients were scheduled to visit the clinic every 2-4 weeks for intrasulcular irrigation of chlorhexidine and delivery of minocycline HCl. Results: We observed statistically significant decreases in PPD, CAL, and BOP after treatment. At the endpoint, bone levels increased in all defects, regardless of the osseous morphology of the intrabony defect. The mean DIB change in deep defects was significantly greater than that in shallow defects. Although the mean bone gain in narrow defects was greater than in wide defects, the difference was not statistically significant. Conclusions: We propose that significant and sustainable improvements in both clinical and radiographic parameters can be expected when intrabony defects around dental implants are managed through a simple nonsurgical approach involving combined intrasulcular chlorhexidine irrigation and local delivery of minocycline HCl.

• 대한화장품학회지
• /
• 제24권3호
• /
• pp.134-145
• /
• 1998

Facial hyperpigmentation in women, which is considered to be a serious cosmetic disability and a cause of mental distress, requires proper management. Melanocyte dendricity is a crucial factor affecting epidermal pigmentation. We found that BQ-788, the endothelin-B (ETB) receptor antagonist, blocks the formation of multi-dendricity which is induced by cocultured keratinocytes. Melanocytes in vivo show numerous dendrites which are in close contact with multiple keratinocytes, forming the epidermal-melanin unit. While melanocytes transfer their melanosomes into the neighboring keratinocytes via dendrites, keratinocytes secrete many growth factors and cytokines that influence viability, morphology, and melanin formation of melanocytes. Endothelin-1 (ET-1), prostaglandin E2(PGE2), and leukotriene-C4 (LT-C4) have been suggested as the candidates for increasing dendricity. Other reports suggested that ET-1 has stimulatory effects on proliferation and melanin formation of melanocytes in vitro. In the present study, using type-specific ET receptor antagonists, we observed how the morphology of melanocytes could be modulated in a coculture system. In addition, the roles of ET-1 for morphology and proliferation on melanocytes were evaluated in different culture media. We suggest that ET-1 increases dendricity and proliferation of melanocytes, and that its dendrite-inducing effect and mitogenic effect are regulated independently.