• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.534-546
• /
• 1990

In this work, an optimum shape synthesis for rolling contact components was done to minimize contact forces considering dynamic characteristics of the system. Even this method was applied to an OHC type cam follower system, it can be expanded to general rolling contact shape design problems which are strictly forced to follow predetermined motion. First, the follower optimum angular motion was derived to minimize the valve peak acceleration while satisfying all the constraints of valve motion. Then the cam and follower contact shape were synthesized to give the proposed follower motion. Theoretically, two components shape to generate a predetermined motion can not be uniquely determined. So the cam shape was syntehsized with parametric synthesis method to minimize the peak contact force between cam and follower when the follower shape is assumed as a circle or an ellipse.

• Journal of Surface Science and Engineering
• /
• v.35 no.2
• /
• pp.129-137
• /
• 2002

The purpose of solderability assessment is to predict the effectiveness of soldering process. It is important for companies pursuing zero defects manufacturing because poor solderability is the major cause of two third of soldering failures. The most versatile solderability method is wetting balance method. However, there exist so many indices for wettability in the wetting balance test e.g. time to reach 2/3 values of maximum wetting force, tine to reach zero wetting force, maximum withdrawal force. In this study, three solderability assessment methods, which were the maximum withdrawal force, the wetting balance and the dynamic contact angle (DCA), were evaluated by comparing each other. The wetting balance technique measures the solderability by recording the forces exerted from the specimen after being dipped into the molten solder. Then the force at equilibrium state can be used to calculate a contact angle, which is known as static contact angles. The DCA measures contact angles occurred during advancing and withdrawing of the specimen and the contact angles are known as dynamic contact angles. The maximum withdrawal force uses the maximum force during withdrawal movement and then a contact angle can be calculated. In this study, the maximum withdrawal force method was found to be an objective index for measuring the solderability and the experiment results indicated good agreement between the maximum withdrawal force and the wetting balance method.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.9
• /
• pp.86-93
• /
• 2010

Any relative deformation between the cutting tool and the workpiece at the machining point, results directly in form and dimensional errors. The source of relative deformations between the cutting tool and the workpiece at the contact point may be due to thermal, weight, and cutting forces. Thermal and weight deformations can be measured at various positions of the machine tool and stored in the compensation registers of the CNC unit and compensated the errors during machining. However, the cutting force induced errors are difficult to compensate because estimation of cutting forces are difficult. To minimize the error induced by cutting forces, it is important to improve the machining accuracy. This paper presents the pre-calculated method of form error induced by cutting forces. In order to estimate cutting forces, Isakov method is used and the method is verified by comparing with the experimental results. In order to this, a cylindrical-outer-diameter turning experiments are carried out according to cutting conditions.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.38 no.4
• /
• pp.204-212
• /
• 2022

Purpose: The aim of this study was to compare changes of bite force, occlusal contact area, and dynamic functional occlusion analysis after occlusal stabilization splint therapy during sleep for one month in a patient with bruxism. Materials and Methods: From October 2021 to July 2022, sleep bruxism of 30 patients who visited the Department of Oral Medicine at Yonsei University College of Dentistry Hospital were recruited. The participants were divided into two groups: using an occlusal stabilization splint during sleep (treatment; n = 15) and not using an occlusal stabilization splint (control; n = 15). Before using the occlusal stabilization splint and one month after, bite force, occlusal contact area and dynamic functional occlusion analysis (ratio of left/right bite forces, average bite forces, maximum bite forces, and maximum contact areas during lateral and anterior and posterior mandibular movements) were performed. Results: There was no difference in bite force and occlusal contact area between the treatment group using the occlusal stabilization splint and the control group not using the occlusal stabilization splint during sleep for one month. However, there were significant differences in the average bite force and maximum bite force in the lateral and anterior and posterior mandibular movements and the maximum contact areas in the anterior and posterior mandibular movements. Conclusion: The occlusal stabilization splint is helpful for sleep bruxism patients who lateral and anterior and posterior mandibular movements. In addition, further studies are needed a double-blind study with a large population.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1304-1317
• /
• 2020

The tubes in a heat exchanger, such as a steam generator (SG), are subjected to crossflow, and interaction between tubes and supports can happen, which can cause fretting wear of tubes. Although many experiments and models have been established, some detailed mechanisms are still not sufficiently clear. In this work, more attention is paid to obtain the regulation of impact and sliding in the complex process and many factors, such as excitation forces and clearances. The responses and contact forces were analyzed to obtain clear understanding of the influences of these factors. Room temperature tests in the air were established. The results show that the effect of clearance on the normal work rate is not monotonous and instead has two peaks. The force ratio can influence the normal work rate by changing the distribution of contact angles, which can result in higher sliding in the contact process. Fretting wear tests are conducted, and the wear surfaces are analyzed by a scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDX). The results of this work can serve as a reference for impactsliding contact analysis between AVBs and tubes in steam generators.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.179-184
• /
• 1995

A new cutting parameter is defined in the spherical part of ball end-mill cutter. A series of slot cutting experiments were carried out to obtain the cutting parameter. The cutter contact area is expressed as the grid posiotion in the cutting plane using Z map. The cutting forces in each grid are calculated and saved as force map, prior to the average cutting forces calculation. The cutting force, in the arbitrary cutting area, can be easily calculated by summing up the cutting forces of the engaged grid in the force map. This model was verified in the inclined surface cutting by cutting test of a cylindrical part.

• Proceedings of KOSOMES biannual meeting
• /
• 2003.11a
• /
• pp.127-133
• /
• 2003

In this study, the impact analysis for the steel fender system that designed for protection of collision between vessel and bridge was performed The size of objective collision vessel assumed as 3000 dead weight tonnage(DWT). The impact forces and the impact energies were estimated by formulas of several design codes, and the steel fender system was designed based on the estimated forces and energy. The bow of objective vessel was modeled as rigid body, and bridge substructure was modeled as fixed support. Since, the impact analysis have the dynamic nonlinear features, such as, material nonlinear, large deformation and contact, explicit structural analysis program was used The analysis results presented that the impact forces formulas in codes have the sufficient conservativeness.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.632-635
• /
• 1996

Flexible parts can be deformed by the contact forces during assembly on the con to rigid parts and thus their successful assembly requires informations about their deformation as well as a misalignment between mating parts. However, because of the nonlinear and complex relationship between parts deformation and assembly reaction forces, it is difficult to acquire all required informations from only the reaction forces during assembly. In this paper, we propose a sensing system consisting of a camera and multiple mirrors for flexible parts assembly. Simulation results show that the system can be effectively used for detecting parts deformation and a misalignment between mating parts.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.376-381
• /
• 2004

A rig was constructed to test the performance characteristics and compare the hydraulic forces exerted on a centrifugal type artificial heart impeller. A conventional shaft. seal and bearing system. while driven by a small electric motor. supported the impeller which was separated from the pump casing by a six degree of freedom force transducer (JR3 Ine). Radial (x. y) and axial (z) hydraulic forces were recorded and compared. At physiological operating conditions. the results indicate that the double entry/exit centrifugal pump encounters a smaller radial force and significantly reduced axial thrust. These experimental results are valuable in the design of a magnetic bearing system to suspend the impeller of a centrifugal artificial heart pump. This experimental technique may also be applied to evaluate the required capacity and predict the lifetime of contact bearings in marine pumps.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1438-1445
• /
• 1992

A new and efficient method is presented to evaluate contact force and motion of an electric railway simple catenary-pantograph system. Overhead lines are regarded as simple strings, and hangers connected to the strings are replaced with concentrated forces acting on them. The displacement of strings due to concentrated forces caused by hangers and pantograph is expressed using Green's function. A system of linear algebraic equations in terms of unknown forces is derived based upon the compatibility requirement at the location of hangers and pantograph. This procedure is more analytic in formulation compared to the existing methods such as finite difference method or normal modes method, and it is expected to be more accurate. Present method has additional advantage that it requires neither numerical differentiation nor system eigenvalues.