• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.3
• /
• pp.17-23
• /
• 2011

To estimate fuel consumption of a vehicle, a car can be tested on chassis dynamometer. In this case, test causes a lot of time and money. To predict the fuel efficiency of vehicles in the design stage or early stage of development, the development of computer simulation model is necessary. Using simulation to predict the fuel consumption, the driving model which consists of time-velocity profile and time-grade profile is necessary In this study, vehicle model is developed in MatLab/simulink to estimate real driving fuel consumption rate with time-velocity profile, time-shift gear profile and time-grade profile. Vehicle model consists of driver model, engine model, power train model, and so on. On-road vehicle tests to verify the vehicle model are carried out for analyzing the result of simulation and comparing with those of the experiments.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.2
• /
• pp.164-170
• /
• 2004

Recently, the demand for micro hard disk drive that provides high-capacity removable storage for handhold electronic devices is growing very rapidly Reducing power consumption is one of the primary control objectives in micro disk drives. The input power delivered to the seek servo system is consumed as heat by the transistors of power amplifier and motor coil resistance. In this paper, we present a new seek servo controller for minimizing the power consumption. We use a Fourier decomposition and nonlinear programming to determine the optimum seek profile that minimizes the power consumption. Also, the trajectory tracking controller is developed for exact tracking of the optimum seek profile. Finally, we present some experimental results using a commercially available micro disk drive in order to demonstrate the superior performance of the proposed controller.

• Smart Media Journal
• /
• v.8 no.4
• /
• pp.72-79
• /
• 2019

The automated demand response (DR) program encourages consumers to participate in grid operation by reducing power consumption or deferring electricity usage at peak time automatically. However, successful deployment of the automated DR program sphere needs careful assessment of appliances load profile (ALP). To this end, the recent method estimates frequency, consistency, and peak time consumption parameters of the daily ALP to compute their potential score to be involved in the DR event. Nonetheless, as the daily ALP is subject to varying with respect to the DR time ALP, the existing method could lead to an inappropriate estimation; in such a case, inappropriate appliances would be selected at the automated DR operation that effected a consumer comfort level. To address this challenge, we propose a more proper method, in which all the three parameters are calculated using ALP that overlaps with DR time, not the total daily profile. Furthermore, evaluation of our method using two public residential electricity consumption data sets, i.e., REDD and REFIT, shows that our energy management systems (EMS) could properly match a DR target. A more optimal selection of appliances for the DR event achieves a power consumption decreasing target with minimum comfort level reduction. We believe that our approach could prevent the loss of both utility and consumers. It helps the successful automated DR deployment by maintaining the consumers' willingness to participate in the program.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.231-233
• /
• 2005

For the low-power design of the mobile multimedia system architecture, this paper modeling the mobile multimedia system and analysis the power consumption profile about the whole communication environment. The mobile system model consist of air interface, RIP front-end, base-band processing module and human interface. For the result of power consumption profile analysis, the power consumption of multimedia processing is above 60% compare to the whole power consumption in mobile multimedia system. To minimize the power consumption in processing module which consumes the large power, this paper proposed the Microscopic DVS technique which applies the optimum voltage for the each multimedia frame. For the simulation result, proposed power minimization technique reduce the power consumption about 30%.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.3
• /
• pp.208-220
• /
• 2006

Energy of wheeled mobile robot is usually supplied by batteries. In order to extend operation time of mobile robots, it is necessary to minimize the energy consumption. The energy is dissipated mostly in the motors, which strongly depends on the velocity profile. This paper investigates various 3-step (acceleration - cruise - deceleration) speed control methods to minimize a new energy object function which considers the practical energy consumption dissipated in motors related to motor control input, velocity profile, and motor dynamics. We performed an analysis on the energy consumption various velocity profile patterns generated by standard control input such as step input, ramp input, parabolic input, and exponential input. Based on these standard control inputs, we analyzed the six 3-step velocity profile patterns: E-C-E, P-C-P, R-C-R, S-C-S, R-C-S, and S-C-R (S means a step control input, R means a ramp control input, P means a parabolic control input, and E means an exponential control input, C means a constant cruise velocity), and suggested an efficient iterative search algorithm with binary search which can find the numerical solution quickly. We performed various computer simulations to show the performance of the energy-optimal 3-step speed control in comparison with a conventional 3-step speed control with a reasonable constant acceleration as a benchmark. Simulation results show that the E-C-E is the most energy efficient 3-step velocity profile pattern, which enables wheeled mobile robot to extend working time up to 50%.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.6
• /
• pp.14-20
• /
• 2015

The Korea ministry of land, infrastructure and transport set the goal of cutting greenhouse gas emissions from the transport sector by 34.3% relative to the business as usual scenario by 2020. In order to achieve this goal, support is being given to education and information regarding eco-driving. As a practical measure, however, a vehicle control strategy for decreasing fuel consumptions and emissions is necessary. Therefore, this paper presents an optimized driving model in order to decrease fuel consumption. Scenarios were established by driving mode. The speed profile for each scenario applied to Comprehensive Modal Emission Model and then each fuel consumption was estimated. Scenarios and speed variation with the least fuel consumption were derived by comparing the fuel consumptions of scenarios. The optimized driving model was developed by the derived the results. The speed profiles of general driver were collected by field test. The speed profile of the developed model and the speed profile of general driver were compared and then fuel consumptions for each speed profile were analyzed. The fuel consumptions for optimized driving were decreased by an average of 11.8%.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.4
• /
• pp.300-306
• /
• 2011

In this paper, we suggest a usage profiles for electric home appliances. In Korea, it is published the records for total consumption of electricity in a house but the electric home appliance consumption records in a households are not. To build the data, we must collect the usage of every appliances in a house and the information of the household which live in the house. Unfortunately, it is hard to get the data because of the worry about the breach of privacy. In this paper, we make a scenarios on the electricity consumption pattern of a few households type. Based on the conjecture, we make the power consumption profiles for some home appliances. Comparison to the total electric consumption records for a house, we found our scenarios are quite reasonable.

• The KSFM Journal of Fluid Machinery
• /
• v.16 no.1
• /
• pp.5-10
• /
• 2013

The performance of screw air compressor is affected by rotor profile, lobe number, air end wrap angle, rotor L/D ratio, suction and discharge ports, revolutions of air end and load regulation control, etc. In general, an efficient screw compressor needs a rotor profile of which has a large flow cross-section area, short sealing lines and a small blow-hole. In this study, experimental study was performed with newly designed $5{\times}6$ rotor profile and various shapes of air end. Results show that the measured specific power consumption of the newly designed screw compressor appeared to be lower than any other published data for the equivalent screw compressors manufactured.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.585-592
• /
• 2009

The performance of screw compressor depends on lots of design parameters of rotor profile, such as length of seal line, wrap angle, blow hole, suction and discharge port size, number of rotor lobe, etc. The optimum rotor profile makes it possible to increase the compression efficiency with low energy consumption, and to minimize the loss of power. In this research, a new rotor profile design and performance analysis are done by computer simulation. It is expected that the volumetric efficiency is improved because the internal leakage is reduced due to the minimization of blow hole and clearance, and the stiffness of rotors is increased due to the reduction of length to diameter ratio. Also, the specific power consumption will be secured for use ranging from low to high operation speed.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.15 no.3
• /
• pp.108-113
• /
• 2007

The performance of a solar water heater incorporating evacuated tubes was evaluated using a transient simulation program, TRNSYS. Simulations were performed for $60^{\circ}C$ of hot water load temperature and for 280 liter of daily hot water volumes and three 400 liter of storage tank volumes. Three patterns of daily hot water consumption profile were used in the present study (morning, lunch and evening). The results show that the increase in solar fraction depends on the load profile, as well as the collector efficiency coefficient. Hot water draw profile has a large effect on the performance of the SDHWS, the morning load profile has the highest solar fraction. The annual solar fraction of the system, at the weather conditions of Jinju is approximately 84% at lunch load pattern, the 280 kg of load volume, 400 kg of tank volume and the $60^{\circ}C$ of load temperature.