• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.11
• /
• pp.13-18
• /
• 2019

The DEM(Digital Elevation Model) is a three-dimensional spatial information that stores the height of the terrain as a numerical value. This means the elevation of the terrain not including the vegetation and the artifacts. The DEM is used in various fields, such as 3D visualization of the terrain, slope, and incense analysis, and calculation of the quantity of construction work. Recently, many studies related to the construction of 3D geospatial information have been conducted, but research related to DEM generation is insufficient. Therefore, in this study, a DEM was constructed using a MMS (Mobile Mapping System), UAV image, and UAV LiDAR (Light Detection And Ranging), and the accuracy evaluation of each result was performed. As a result, the accuracy of the DEM generated by MMS and UAV LiDAR was within ± 4.1cm, and the accuracy of the DEM using the UAV image was ± 8.5cm. The characteristics of MMS, UAV image, and UAV LiDAR are presented through a comparison of data processing and results. The DEM construction using MMS and UAV can be applied to various fields, such as an analysis and visualization of the terrain, collection of basic data for construction work, and service using spatial information. Moreover, the efficiency of the related work can be improved greatly.

• Journal of the Korea Concrete Institute
• /
• v.28 no.1
• /
• pp.59-65
• /
• 2016

Commercial synthetic resins with great amount of hydrogen atoms were investigated for neutron shielding aggregates. Total three types of resins were considered in this study: high density polyethylene (HDPE), polypropylene (PP), and ultra molecular weight polyethylene (UPE). When these resins replaced 20, 40, 60 vol% of fine aggregates, mechanical properties were first evaluated including compressive and tensile strengths, and then image/microstructure analyses such as cross-section analysis, SEM, and X-ray CT were performed. The results showed that the compressive and tensile strengths decreased with the increase of replacement ratio of HDPE and PP, which was found through image analysis that it was closely related to the distribution of resins at the failure surface of test specimens. The strength reduction of UPE was quite small compared to HDPE and PP but it abruptly increased when the replacement level exceeded 60 vol%. The results of microstructure analyses indicated that the replacement level significantly affected the amount of air void so that it is critical to determine the reasonable amount of UPE to make cementitous materials for neutron shielding.

• Journal of KIBIM
• /
• v.7 no.1
• /
• pp.45-53
• /
• 2017

Continuous research efforts have been made on acquiring location data on construction sites. As a result, GPS and RFID are increasingly employed on the site to track the location of equipment and materials. However, these systems are based on radio frequency technologies which require attaching tags on every target entity. Implementing the systems incurs time and costs for attaching/detaching/managing the tags or sensors. For this reason, efforts are currently being made to track construction entities using only cameras. Vision-based 3D tracking has been presented in a previous research work in which the location of construction manpower, vehicle, and materials were successfully tracked. However, the proposed system is still in its infancy and yet to be implemented on practical applications for two reasons. First, it does not involve entity matching across two views, and thus cannot be used for tracking multiple entities, simultaneously. Second, the use of a checker board in the camera calibration process entails a focus-related problem when the baseline is long and the target entities are located far from the cameras. This paper proposes a vision-based method to track multiple workers simultaneously. An entity matching procedure is added to acquire the matching pairs of the same entities across two views which is necessary for tracking multiple entities. Also, the proposed method simplified the calibration process by avoiding the use of a checkerboard, making it more adequate to the realistic deployment on construction sites.

• Journal of Construction Engineering and Project Management
• /
• v.2 no.3
• /
• pp.1-7
• /
• 2012

The reconstruction of surfaces from unorganized point clouds can provide very useful information for construction managers. Although point clouds are generally created using 3D scanners, they can also be generated via the structure-from-motion technique using a sequence of images. Here we report a novel surface reconstruction technique for modeling and quantifying earthworks that can be used for preliminary planning, project updates and estimating of earthwork quantities, as well as embedded planning systems in construction equipment. The application of structure-from-motion techniques in earth works is examined and its advantages and limitations identified. Data from 23 earthwork excavation construction sites were collected and analyzed. 3D surface reconstructions during the construction phase were compared to the original land form. Similar experiments were conducted with piles of earth and the results analyzed to determine appropriate ranges of use for structure-from-motion surface reconstructions in earthwork applications. The technique was found to be most suited to pile of materials with volumes less than 2000 m3. Piles up to 10 m in height and with base areas up to $300m^2$ were also successfully reconstructed. These results should be of interest to contractors seeking to utilize new technology to optimize operational efficiency.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.47-48
• /
• 2022

The positioning technology that measures the position of a person or object is a key technology to deal with the location of the real coordinate system or converge the real and virtual worlds, such as digital twins, augmented reality, virtual reality, and autonomous driving. In estimating the location of a person or object at an indoor construction site, there are restrictions that it is impossible to receive location information from the outside, the communication infrastructure is insufficient, and it is difficult to install additional devices. Therefore, this study tested the direct sparse odometry algorithm, one of the visual Simultaneous Localization and Mapping (vSLAM) that estimate the current location and surrounding map using only image information, at an indoor construction site and analyzed its applicability as an indoor positioning technology. As a result, it was found that it is possible to properly estimate the surrounding map and the current location even in the indoor construction site, which has relatively few feature points. The results of this study can be used as reference data for researchers related to indoor positioning technology for construction sites in the future.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.186-187
• /
• 2014

The principal government building of Kyungsanbuk-do was designed to show korean traditional architecture with tile-roofed house to reflect the image of Kyungsangbuk-do as the province of traditional culture. The roof of korean traditional architecture is the most importanat part that distinguishes the design character of a building and is important to determine degree of completion. As this is so, in the design phase, we reviewes the design documents about the proportional and slope of the roof, durability and sizes of component material and the structure of eaves. In the construction phase, it was required to cooperated with specialists of traditional architecture for realization of traditional beauty of the buildings as designed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.618-625
• /
• 2003

The recent development of PSC girder bridges are mostly dedicated for optimization of self-weight, simplification of girder section for easy construction and minimization of maintenance efforts. Moreover some of those bridges are required as a landmark facility which raises the image of locality and harmony with surroundings. An extradosed bridge is one of the best alternates which not only covers the longer span than PSC box girder and also performs the role of landmark facility with much cheaper cost than cable stayed bridge. Hyundai is carrying out the construction of unique style extradosed bridge which have central suspension system and uniform girder depth named Keong-An grand bridge on the Sungnam-Janghowon Express highway. In this paper, major process of design and construction features of Keong-An bridge is presented.

• International conference on construction engineering and project management
• /
• 2017.10a
• /
• pp.252-259
• /
• 2017

Nowadays, the existing manual method for recording actual progress of the construction site has some drawbacks, such as great reliance on the experience of professional engineers, work-intensive, time consuming and error prone. A method integrating computer vision and BIM(Building Information Modeling) is presented for indoor automatic progress monitoring. The developed method can accurately calculate the engineering quantity of target component in the time-lapse images. Firstly, sample images of on-site target are collected for training the classifier. After the construction images are identified by edge detection and classifier, a voting algorithm based on mathematical geometry and vector operation will divide the target contour. Then, according to the camera calibration principle, the image pixel coordinates are conversed into the real world Coordinate and the real coordinates would be corrected with the help of the geometric information in BIM model. Finally, the actual engineering quantity is calculated.

• International conference on construction engineering and project management
• /
• 2011.02a
• /
• pp.420-425
• /
• 2011

Corporate Social Responsibility has become a hot issue for modern enterprises recently. Under this trend, companies have to focus on what they can do for society instead of on just making profits. This paper is to explore the relationship between ecological corporate social responsibility and organizational performance in the construction industry in Taiwan. 192 samples were collected from Taiwan's general contractors and analyzed using factor analysis, correlation analysis and path analysis. This study found: (1) in general, the contractors in Taiwan don't devote much to realizing ecological corporate social responsibility, and there is still much room for improvement; (2) the correlation analysis results indicated there are significant positive relationships between ecological corporate social responsibility and organizational performance; and (3) according to the path analysis results, a contractor can improve its business performance by improving its realization of corporate social responsibility.

• Architectural research
• /
• v.12 no.2
• /
• pp.53-62
• /
• 2010

The purpose of this study is to examine design preferences for the sales spaces of duty-free shops (DFSs) by conducting image evaluations. The results will help improve quality by influencing designs for the construction, extension or remodeling of these shops. An image measurement method, the semantic differential method, was used to measure cognitive structure using photos of shops. Photos were collected of the DFS at Jeju Island, as well as photos of brand stores designed by architects. Two sets of 16 photos (32 different photos in all) were selected according to photo classification standards and design concepts, both decided by reviewing previous studies and related materials. The evaluation and survey were done by two sets of subjects: sales employees, who have experience and special knowledge of the evaluation of sales space; and students majoring in architecture. To strengthen the evaluation results, I conducted a preliminary survey and a main survey, verifying and complementing findings. 116 surveys were conducted, of which 14 were of poor quality and rejected, leaving and 102 to be analyzed. The collected surveys were statistically analyzed, using SPSS 12.0 for Windows. Reliability, image profile, factor and multi-dimensional scaling analyses were conducted. As a result, image evaluation structure and characteristics were obtained for sales spaces of DFSs, confirming the difference between them and other spaces.