• 전력전자학회논문지
• /
• 제9권4호
• /
• pp.372-380
• /
• 2004

본 논문은 기존의 2개의 전력 처리단을 갖는 컨버터를 단일 전력단으로 구성하고, ZVS기법을 이용한 고역률 단일전력단 고주파 공진 AC-DC 컨버터를 제안하고 있다. 입력단에 승압형 역률개선 인덕터를 연결하여 일정 듀티비와 가변 스위칭 주파수로 입력전류를 불연속 모드로 제어함으로써 입력 역률을 개선하는 것이 가능하였다. 종래의 2개 전력 처리단을 가지는 컨버터의 경우 역률 제어용 스위치가 별도로 필요하지만 전력 처리단을 하나로 단일화 시키므로써 컨버터의 구성이 간략화 되어져, 비용의 저감과 신뢰성을 증가시킬 수 있는 등의 장점이 있다. 본 연구는 고역률 단일전력단 AC-DC 컨버터의 동작원리와 무차원화 파라미터를 이용한 특성평가를 범용성 있게 행하여, 특성평가에서 산출한 특성값을 기초로 하여 실험장치를 제작하였으며, 실험치와 이론치를 비교ㆍ검토하여 제안 회로의 특성해석의 정당성을 입증하고 있다.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.300-305
• /
• 2000

We have investigated the dielectric and electrical characteristics of palmitic acid(PA) stearic acid(SA) and arachidic acid(AA) Langmuir-Blodgett(LB) films because these fatty acid systems have a same hydrophilic group and a different hydrophobic one(methylene group or alkyl chain length). The fatty acid systems were used as LB films and the status of the deposited films was confirmed by evaluating the transfer ratio the UV absorption and the capacitance. The dielectric characteristics such as the frequency-capacitance characteristics and the dielectric dispersion and absorption characteristics of PA SA and AA through-plane were measured. The relative dielectric constants of PA, SA and AA LB films were about 3.0~4.6, 2.7~3.0 and 2.4~3.0 respectively. That is the relative dielectric constants were decreased in proportion to the chain length of methylene group. Also the dielectric dispersion and absorption of each fatty acid LB films have arisen from spontaneous polarization of dipole polarization in the range of 10$^4$~10$^{5}$ ［Hz］. The conductivity of PA, SA and AA LB films obtained from I-V characteristics were about 9$\times$10$^{-14}$ , 3$\times$10$^{-14}$ and 5$\times$10$^{-15}$ ［S/cm］. respectively. These results have shown the insulating materials and could control the conductivity y changing the length of methylene group. Also we have confirmed that the barrier height of fatty acid systems were almost the same ones obtained from dielectric characteristics.

• 한국전기전자재료학회논문지
• /
• 제11권10호
• /
• pp.826-832
• /
• 1998

In this study the thin films with the structure of Si+SiO$_2$+TiN are made by RF supttering method. TiN, which has small diffusion coefficient and low resistivity, is evaporated between SiO$_2$ and Al layers. It investigates the V-R characteristics depending on the thickness of SiO$_2$ which is used as insulation layer and researches its effects on voltage stability of thin film and varistor. These films show very small resistance valus in negative(-) voltage and large and large value in positive voltage band, and with the increase of voltage, resistance value is rapidly reduced and the satisfactory characteristic of varistor is shown at +1[V]. It is found that resistance value of TiN thin film is small and also TiN thin film has more current than the thin film which is not evaporated by TiN thin film. When Al electrode is evaporated of SiO$_2$ thin film, spiking occurs, but the spiking can be prevented with evaporation of TiN between SiO$_2$ and Al layers and this thin films in made easily because of its good attachment. With the increase of voltage, the resistance is changed into non-linear pattern and the bidirectional varistor characteristic is shown and then its theory can be verified by this experiment. Accordingly, when TiN is evaporated of Si Wafer(n-100), it obtains better voltage-resistance than thin film which is not evaporated and also when varistor character is used electrically to automatic control element such as elimination of flame, power distribution arrestor and constant voltage compensation, satisfactory reproducibilities are expected.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 추계학술발표회 초록집
• /
• pp.1-2
• /
• 2000

In chip plating, several parameters must be taken into consideration. Current density, solution concentration, pH, solution temperature, components volume, chip and media ratio, barrel geometrical shape were most likely found to have an effect to the process yields. The 3 types of barrels utilized in chip plating industry are the onventional rotating barrel, vibrational barrel(vibarrel), and the centrifugal type. Conventional rotating barrel is a close type and is commonly used. The components inside the barrel are circulated by the barrel's rotation at a horizontal axis. Process yield has known to have higher thickness deviation. The vibrational barrel is an open type which offers a wide exposure to electrolyte resulting to a stable thickness deviation. It rotates in a vertical axis coupled with multi-vibration action to facilitate mixed up and easy transportation of components. The centrifugal barrel has its plated work centrifugally compacted against the cathode ring for superior electrical contact with simultaneous rotary motion. This experiment has determined the effect of barrel vibration intensity to the plating thickness distribution. The procedures carried out in the experiment involved the overall plating process., cleaning, rinse, Nickel plating, Tin-Lead plating. Plating time was adjusted to meet the required specification. All other parameters were maintained constant. Two trials were performed to confirm the consistency of the result. The thickness data of the experiment conducted showed thatbthe average mean value obtained from higher vibrational intensity is nearer to the standard mean. The distribution curve shown has a narrower specification limits and it has a reduced variation around the target value. Generally, intensity control in vi-barrel facilitates mixed up and easy transportation of components. However, it is desirable to maintain an optimum vibration intensity to prevent solution intrusion into the chips' internal electrode. A cathodic reaction can occur in the interface of the external and internal electrode. 2H20 + e $\rightarrow$M/TEX> 20H + H2.. Hydrogen can penetrate into the body and create pressure which can cause cracks. At high intensity, the chip's motion becomes stronger, its contact between each other is delayed and so plating action is being controlled. However, the strong impact created by its collision can damage the external electrode's structure there by resulting to bad plating condition.

• 청정기술
• /
• 제16권4호
• /
• pp.297-303
• /
• 2010

본 연구에서는 유체유동해석프로그램인 Fluent를 이용하여 연료극 지지채식 관형 고체산화물 연료전지(SOFC)에서의 연결재 구조에 따른 성능 변화를 고찰하였다. 실험적 사실과 부합되는 이론적 결과를 확보하기 위해서는 전기적으로 전극과 하나로 되어있는 연결재의 구조가 전지 성능에 어떠한 영향을 미치는지 살피는 것이 중요하다. 두께가 작은 연결재가 단전지 성능을 우수하게 하는 것으로 보아 옴(ohmic) 저항에 직결되는 연결재의 두께가 전지 성능에 있어 주요 변수임을 확인하였다. 일정 두께로 고정된 조건 하에 연결재 폭을 변화시킨 경우, 전지 성능은 상대적으로 큰 차이를 보이지 않았다. 이는 본 연구에서 고려한 SOFC의 관형 구조 특성상 연결재의 폭으로는 원주 방향으로 흘러가는 전류 경로를 효과적으로 단축시킬 수 없기 때문으로 사료된다.

• Structural Engineering and Mechanics
• /
• 제90권4호
• /
• pp.371-390
• /
• 2024

Investigating the impact of openings on the structural behavior of ferrocement I-beams with two distinct types of reinforcing metallic and non-metallic meshes is the primary goal of the current study. Up until failure, eight 250x200x2200 mm reinforced concrete I-beams were tested under flexural loadings. Depending on the kind of meshes used for reinforcement, the beams are split into two series. A control I-beam with no openings and three beams with one, two, and three openings, respectively, are found in each series. The two series are reinforced with three layers of welded steel meshes and two layers of tensar meshes, respectively, in order to maintain a constant reinforcement ratio. Structural parameters of investigated beams, including first crack, ultimate load, deflection, ductility index, energy absorption, strain characteristics, crack pattern, and failure mode were reported. The number of mesh layers, the volume fraction of reinforcement, and the kind of reinforcing materials are the primary factors that vary. This article presents the outcomes of a study that examined the experimental and numerical performance of ferrocement reinforced concrete I-beams with and without openings reinforced with welded steel mesh and tensar mesh separately. Utilizing ANSYS-16.0 software, nonlinear finite element analysis (NLFEA) was applied to illustrate how composite RC I-beams with openings behaved. In addition, a parametric study is conducted to explore the variables that can most significantly impact the mechanical behavior of the proposed model, such as the number of openings. The FE simulations produced an acceptable degree of experimental value estimation, as demonstrated by the obtained experimental and numerical results. It is also noteworthy to demonstrate that the strength gained by specimens without openings reinforced with tensar meshes was, on average, 22% less than that of specimens reinforced with welded steel meshes. For specimens with openings, this value is become on average 10%.

• The Korean Journal of Physiology and Pharmacology
• /
• 제26권5호
• /
• pp.313-323
• /
• 2022

Atrial fibrillation (AF) is the most common supraventricular arrhythmia, and it corresponds highly with exercise intensity. Here, we induced AF in mice using acetylcholine (ACh)-CaCl₂ for 7 days and aimed to determine the appropriate exercise intensity (no, low, moderate, high) to protect against AF by running the mice at different intensities for 4 weeks before the AF induction by ACh-CaCl₂. We examined the AF-induced atrial remodeling using electrocardiogram, patch-clamp, and immunohistochemistry. After the AF induction, heart rate, % increase of heart rate, and heart weight/body weight ratio were significantly higher in all the four AF groups than in the normal control; highest in the high-ex AF and lowest in the low-ex (lower than the no-ex AF), which indicates that low-ex treated the AF. Consistent with these changes, G protein-gated inwardly rectifying K⁺ currents, which were induced by ACh, increased in an exercise intensity-dependent manner and were lower in the low-ex AF than the no-ex AF. The peak level of Ca²⁺ current (at 0 mV) increased also in an exercise intensity-dependent manner and the inactivation time constants were shorter in all AF groups except for the low-ex AF group, in which the time constant was similar to that of the control. Finally, action potential duration was shorter in all the four AF groups than in the normal control; shortest in the high-ex AF and longest in the low-ex AF. Taken together, we conclude that low-intensity exercise protects the heart from AF, whereas high-intensity exercise might exacerbate AF.

• 해양환경안전학회지
• /
• 제29권6호
• /
• pp.666-671
• /
• 2023

국제적인 선박 배출 가스에 대한 환경 규제가 점차 강화됨에 따라 전기추진 및 하이브리드 추진선박에 대한 관심이 증대되고 있으며, 이러한 선박에 적용하기 위한 다양한 솔루션이 개발 및 적용되고 있는데 특히 전력계통의 안정화, 시스템의 효율성을 높이기 위한 방안으로 직류배전시스템이 적용되고 있다. 또한, 선박용 직류배전시스템에 대한 안전 및 성능에 대한 검증 및 시험의 중요성이 요구되고 있다. 본 연구는 직류배전 테스트베드 구축 및 직류배전(가변속 발전)시스템에 대한 성능을 검증하고 연료소모량 분석한 결과로서 선박용 직류배전에 적용되고 있는 가변속 발전시스템을 적용하였으며, 발전기에서 출력되는 전력을 정류기를 통해 직류전력으로 변환하여 시스템에 연계하고 이러한 장치들을 감시 및 제어하기 위한 시스템을 개발하였다. 이러한 직류배전 시스템을 적용한 시험을 통해 최대 전압은 751.5V이고 최소전압은 731.4V가 계측되어 전압변동률은 2.7%로 3% 이내에서 안정적으로 전압이 공급되는 것을 확인하였고 부하변동에 따라 가변속 발전시스템을 적용하였을 경우 연료소모량이 기존 정속발전시스템과 비교하여 구간에 따라 최대 20%이상 연료절감이 되는 것을 시험을 통해 확인하였다.

• 융합신호처리학회논문지
• /
• 제19권2호
• /
• pp.61-67
• /
• 2018

용접예열은 본 용접 전에 금속이 융착되는 모재면을 일정한 온도로 가열하는 것을 의미한다. 냉각속도 조절에 따른 재료 경화 정도 감소, 불순물 편석억제, 열적 변형방지, 그리고 수분제거 등 인접 영향부의 균열을 방지할 수 있다. 이러한 이유에서 고품질의 용접을 위하여 반드시 필요한 작업이다. 유도가열은 전자기유도 현상을 응용하여 전기에너지를 열에너지로 변환시키는 효율적인 가열방식이다. 기체 및 액체를 이용한 연소발열과 비교하여 신속한 가열뿐만 아니라 청결하고, 안정적이며, 경제적이다. 단순한 구조로 주파수와 코일의 형태를 변형하여 가열체의 형상, 깊이, 재질에 관계없이 가열할 수 있다. 본 논문에서는 유도가열 기법을 이용하여 저주파 용접예열 시스템을 구현하였으며, 3종의 자동차 변속기 부품을 대상으로 권선코일 내에서 각 변속기 높이에 따라 권선코일 저항, 인덕턴스 및 자동차 변속기 부품의 온도변화를 관찰한 결과 전류의 변화는 저주파 가열에 있어 매우 중요한 요인으로 작용함을 확인하였다.

• Journal of Acupuncture Research
• /
• 제17권2호
• /
• pp.231-246
• /
• 2000

Acupuncture has been used for treatment of numerous diseases, especially for pain control in the oriental culture. However, the mechanism of pain control by acupuncture was not clear so far. The present study was examined that the effects of electro-acupuncture (EA) applied to the acu-point of extra-segmental area on modulation of formalin induced pain in Sprague - Dawley rats. In order to apply EA to acu-points in the plantar area of right fore paws, a pair of teflon - coated stainless steel wires were implanted in HT 7 (shin-mun) and PC 7 (dae-neong) 5 days before behavioral test. A behavioral test was performed by means of video camera after injection of 5% formalin ($50{\mu}l$) into the lateral plantar region of left hind paw. EA was delivered by a constant current stimulator at 4~5 mA, 2 ms, and 10 Hz for 30 min. The electromyographic activities were recorded in the biceps femoris muscle under chloral hydrate anesthesia. Test stimuli with 1~9mA were applied to the sural nerve territory including the medial portion of the 4th toe and the lateral portion of the 5th toe. Behavioral responses including favoring, flinching and bitting were occured in the biphasic pattern, such as the lst phase (0~5 min) and the 2nd phase (20~45 min) after formalin injection. However, EA (4~5 mA, 2 ms, 10 Hz) significantly inhibited Che behavioral responses. EMG activities of flexor reflex had a latency of 100~300 ms and thresholds of test stimuli for EMG were 4~5 mA in normal rats. Injection of formalin decreased threshold of test stimuli and increased EMG activities for 2hrs after injection. However, EA significantly inhibited EMG activities of flexor reflex increased by formalin and recovered EMG evoked thresholds. These results suggest that contralateral extra-segmental EA inhibits the first and second phases of formalin induced pain but their mechanism be needed to examine additionally.