• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.3
• /
• pp.588-594
• /
• 2001

The aim of this paper is to develop the low temperature vacuum dryer, with low initial investments and operating costs, easy operating method and trouble-free operation Usally operations just below atmospheric pressure, as with direct dryers, but some are built for vacuum operation with pressure as low 50 mmHg abs. The lowers the boiling point to $39^{\circ}C$ The experimental data of quantitative analysis for using practically were obtained by the constant drying rate period and reducing drying rate period according to the temperature of hot water which is the experimental parameters of present experiment. As the results, it took about 20 hours for material to reach about 18% of the final moisture content is order to store products for a long time about 450% of the early moisture content at the beginning of drying and maximum drying rate comes to about 0.30 kg/m2hr at about 350% of the moisture content.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.25 no.3
• /
• pp.453-459
• /
• 1996

This study was carried out to determine the changes in quality during the drying process and the optimum drying condition for utilizing soybean curd residue. The quality criteria for soybean curd residue were acid value, peroxide value, fatty acid composition and microbial concentration. The acid values of soybean curd residue were 7.5, 4.5 and 5.9 KOH mg/g upon 12 hour drying with open-air sun, ambient-air blast and warm-air blast, respectively. The numbers of total aerobic bacteria and molds increased remarkably during drying with open-air sunlight, ambient-air blast and warm-air blast except for hot air blast. Among different drying methods, the hot air blast drying(1kg of sample) was the most effective methods, which completed in three hours. Also, the drying method demonstrated a typical drying curve ; settling down, constant rate drying and falling rate drying period were shown within one hour, from one and three hours and after three hours, respectively. Moreover, there was significant variation in the constant drying period for the quality of soybean curd residue.

• Journal of Biosystems Engineering
• /
• v.41 no.4
• /
• pp.342-356
• /
• 2016

Purpose: The drying of a thin layer of native cassava starch in a tray dryer was modeled to establish an equation for predicting the drying behavior under given conditions. Methods: Drying tests were performed using samples of native cassava starch over a temperature range of $40-60^{\circ}C$. We investigated the variation in the drying time, dynamic equilibrium moisture content, drying rate period, critical moisture content, and effective diffusivity of the starch with temperature. The starch diffusion coefficient and drying activation energy were determined. A modification of the model developed by Hii et al. was devised and tested alongside fourteen other models. Results: For starch with an initial moisture content of 82% (db), the drying time and dynamic equilibrium moisture content decreased as the temperature increased. The constant drying rate phase preceded the falling rate phase between $40-55^{\circ}C$. Drying at $60^{\circ}C$ occurred only in the falling rate phase. The critical moisture content was observed in the $40-55^{\circ}C$ range and increased with the temperature. The effective diffusivity of the starch increased as the drying temperature increased from 40 to $60^{\circ}C$. The modified Hii et al. model produced randomized residual plots, the highest $R^2$, and the lowest standard error of estimates. Conclusions: Drying time decreased linearly with an increase in the temperature, while the decrease in the moisture content was linear between $40-55^{\circ}C$. The constant drying rate phase occurred without any period of induction over a temperature range of $40-55^{\circ}C$ prior to the falling rate period, while drying at $60^{\circ}C$ took place only in the falling rate phase. The effective diffusivity had an Arrhenius relationship with the temperature. The modified Hii et al. model proved to be optimum for predicting the drying behavior of the starch in the tray dryer.

• Korean Journal of Food Science and Technology
• /
• v.14 no.4
• /
• pp.342-349
• /
• 1982

Filefish muscle in the form of thin plate $(5{\times}10{\times}0.4\;cm)$ was dried in a forced air dryer at $47.5^{\circ}C$ to study the relation between dehydration mechanism and water activity. The dryer was designed in such a way that the temperature, relative humidity and velocity of air could be controlled. The whole dehydration process of the filefish muscle was divided into two different drying rate periods, constant and falling rate period. During the constant drying rate period, the drying rate was proportional to the square root of air velocity under the conditions of constant temperature and relative humidity of air. The falling rate period was further divided into two different falling drying rate periods, first and second falling rate period. The first falling rate period was an unsaturated surface drying period caused by partial unsaturation of the drying surface with capillary condensed free water diffused from the internal part of the filefish muscle. At this stage he drying rate was mainly dependent on the relative humidity at constant air temperature, and case-hardening phenomenon started at the end of this stage. The moisture content and the water activity at which the second falling rate period started were not constant, because the drying rate of the first falling rate period was strongly dependent on the air humidity. The second falling rate period was again divided into two drying rate periods, former and latter period. The drying rates of both of these periods were independent on the external air humidity. During the former period of the second falling rate period, the dehydration was proceeded by diffusion and vaporization of capillary condensed free water in filefish muscle. The diffusion coefficient of water was $2.89{\times}10^{-10}m^2/sec\;at\;47.5^{\circ}C$. At this stage, the case-herdening continued until the water activity reduced to 0.7. The latter period of the second falling rate period started at the water activity of 0.45. The dedydration was proceeded by diffusion and vaporization of bound water, which adsorbed in multimolecular layers, through the hardened drying surface. The number of molecular layers was 4, and the diffusion coefficient of water during this stage was $4.38{\times}10^{-11}m^2/sec\;at\;47.5^{\circ}C$.

• Korean Journal of Food Science and Technology
• /
• v.33 no.6
• /
• pp.706-713
• /
• 2001

The influencing factor in drying characteristics of fluidized bed drying with different drying conditions for husked barley were carried out. This fluidized drying mechanism of husked barley was consisted of consecutive two falling rate parts, first falling rate period and second falling rate period without showing constant rate period. The drying rate constant was increased with decreasing charged amount and relative humidity and increasing air temperature and air velocity. Since the drying rate constant expressed by Arrhenius type equation in the falling rate period showed good linearity, the falling rate period was condsidered as the controlling step. The activation energy of first falling step was 1,100 cal/gmol, while for second falling step the values showed 1,600 cal/gmol.

• Applied Biological Chemistry
• /
• v.17 no.1
• /
• pp.42-48
• /
• 1974

Hot air thin layer drying method was studied for red pepper, Capsicum annum var. longum as the whole and cut pod states, at various temperature and air velocities. Drying curve of whole pod showed a settling down period followed by the first and second falling rate periods. By lowering the drying temperature, the first falling rate period approached to a constant rate one. Cut drying curve had simple falling rate period and also cut drying method could effectively shorten the drying time. Drying rate constant, k, was varied with time for both the drying methods and the plots of k vs. time in two methods sugested the different drying mechanisms. When an average k was taken as a constant value, the following equations; $M-M_e/M_o-M_e=e^{-0.118t}$ and $M-M_e/M_o-M_e=e(-0.342t^{0.128})$ were applicable for whole and cut drying, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.99-107
• /
• 1997

This study was executed to test the possibility of replacement for domestic Japanese larch(Larix leptolepis) for hardwoods and to acquire the information about the effects of drying temperature on internal temperature, moisture content and drying defects. In high-temperature drying, internal temperature increased rapidly to boiling point, immediately after that point the internal temperature rising rate was reduced. In the case of drying at temperature of $125^{\circ}C$, internal temperature could reach at boiling point in a very short time. Moisture content in high-temperature drying showed constant drying rate period and first period of falling rate drying together in 4 hours since experiment begun. There was no strong correlation between initial moisture content and final moisture content. Average drying rate at $115^{\circ}C$, $120^{\circ}C$ and $125^{\circ}C$ was 1.42%/hr, 1.88%/hr and 2.02%/hr, respectively; the case of drying temperature of $125^{\circ}C$ showed most rapid drying rate. Drying rate of $125^{\circ}C$ was so rapid that it showed more severe shrinkage, bow, collapse, end check, and internal check development than in other drying conditions. The result of this study showed the strong possibility of high-temperature drying for Japanese larch, and to dry Japanese larch optimally, dry bulb temperature should not exceed $120^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.2
• /
• pp.61-70
• /
• 1994

This study was executed to find the applicability of press drying of tree disk by investigating the shrinkage and drying defect and to form appropriate model by comparing the actual moisture content(MC) and internal temperature in respect of drying time with calculated values based computer simulation to which was applied finite difference method. In press drying disk, heating period, constant drying rate period maintained plateau temperature at 100$^{\circ}C$ and falling drying rate period were significantly distinguished. Actual MC and internal temperature were analogous to those calculated at comparing points. Heat transfer model formed by Fourier's law using specific heat of moist wood and conduction coefficient considering fractional volume of each element of wood cell wall, bound water, free water and air showed applicability as basic data to developing heat expansion, shrinkage and drying stress during press drying. Also mass transfer model formed by Fick's diffusion law using water vapor diffusion coefficient showed applicability. Longitudinal shrinkage was developed by pressure of hot press and tangential shrinkage was restrained by hygrothermal recovery. The heart check, surface check and ring failure were occurred differently in species, but V-shaped crack didn't develop.

• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.48-57
• /
• 1982

In order to improve the quality of traditionally sun-dried red peppers and to increase the efficiency of drying performance, three types of solar dryers were designed and built, and drying performance of the solar dryers was compared to traditional sun drying. Results obtained from the experiment are summarized as fallows: 1. The air temperature and relative humidity profiles over a 8-hour period measured at the specified locations in the drying chamber of solar dryers appeared to have large variation in each dryer. The rate of drying increased with the temperature rise in the drying chamber of the solar dryer. 2. In general. drying with solar dryers proceeded faster than traditional sun drying. With A'-type of solar dryer developed in the second experiment it was possible to dry red peppers in seven days from an initial moisture content of 80% to safe storage conditions. The drying time with the A'-type solar drier was 50% shorter compared to traditional sun drying. 3. Red peppers appeared to have an increasing or constant-rate drying period until the weight of the product was reduced to about one half the initial weight, followed by a falling-rate drying period. When the dried red peppers were exposed to the atmospere during the night, the moisture content increased as much as 6%, which is much higher than for the grains. 4. It was suggested from the experiment that either a heat storage system or a supplemental heating system in the solar dryer was desirable for more efficient drying operation. 5. It was shown that the solar dryer developed in this study may be suitable for drying other vegetables and fishes, and also offered additional advantages of saving in drying time, maintaining sanitation and minimizing contamination by dust, insects and unfavorable weather condition.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.58-66
• /
• 2016

This study was performed to investigate drying characteristics and quality properties of dried persimmon with vacuum drying process. Drying characteristic curve of the dried persimmon showed that the constant rate drying period and falling rate drying period exist definitely. $_{\circ}Brix$, sugar content and hardness value of the dried persimmon increased as the vacuum pressure and heating temperature increased, but L value of the dried persimmon lower. The results indicated that the optimal conditions were at vacuum pressure of 40~50kPa abs., heating temperature of $30^{\circ}C$ and drying time of 3~4days.