• 융복합기술연구소 논문집
• /
• 제3권1호
• /
• pp.19-23
• /
• 2013

This study is concerned with air-conditioning system in use of thermoelectric device. It is introduced that the well designed structures for better cooling & heating performance with high efficiency. And also it is performed that the system performance test of four types trial products for the use of hybrid commercial vehicle. System performance is affected by many component parts, especially heat sink design & power control method. It is applied that dual extrusive fin tube with buffer zone for the effective radiating of circulating liquid in tube. And also it is applied that power supply method with constant-current system. It is attained that system cooling capacity is 1.2kW, COP is 0.95.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 A
• /
• pp.466-468
• /
• 2002

In order to newly define and specify the performance and the testing method of the high-voltage circuit breaker, IEC 62271-100 was published in May, 2001 and took place of IEC 60056 which had been used since 1987. This new standard intensifies the requirement and the test method of the circuit breaker and also domestic manufacturer makes progress the new product development. And, KERI also goes on the build-up project of short-circuit testing facilities for fulfilling the testing method requirements in new IEC 62271-100. This paper introduce the limiting method of short-circuit making current by controlling the time constant of dc component.

• Journal of Power Electronics
• /
• 제12권2호
• /
• pp.233-241
• /
• 2012

This paper presents a design of a 30kW 250V/530V bidirectional DC-DC converter to be used in an electrical car. A detailed explanation of the design is given. The system uses two phase shifted half bridge (boost and buck) topologies to reduce the ripple current in the output capacitor. The converter has an efficiency of 95% at nominal power. It works as a constant voltage in one direction and as a constant current in the other to charge the batteries. Simulations and measurement are done at high power to test the efficiency.

• 동력기계공학회지
• /
• 제15권2호
• /
• pp.42-48
• /
• 2011

440A martensitic stainless steels which were modified with reduced carbon content(~0.5%) and addition of small amount of nickel, vanadium, tungsten and molybdenum were manufactured. Effects of alloying elements and tempering temperatures on the uniform corrosion in the solution of lN H2S04 were investigated through the electrochemical polarization test. When tempering temperature is constant, corrosion current density in active-passive transition point, Icorr, decreased a little with an increase of austenitizing temperature. In addition to this, when austenitizing temperature is constant, longer holding time showed a little lower Icorr and Ipass, passive current density. And when austenitized at $1050^{\circ}C$ and tempered in a range of $350{\sim}750^{\circ}C$, best anti-corrosion properties were obtained at $350^{\circ}C$ tempering temperature while worst at $450^{\circ}C$ or $550^{\circ}C$. The specimens tempered at below $450^{\circ}C$ and above $550^{\circ}C$, similar and good anti-corrosion characteristics were obtained regardless of alloying elements added, showing anti-corrosion characteristics are influenced more by tempering temperature than by alloying elements.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.240-249
• /
• 2018

Individual DC voltage balance problem is an inherent issue for cascaded H-bridge (CHB) based converter. When the CHB-based static synchronous compensator (STATCOM) is operating at zero current mode, the software-based individual DC voltage balancing control techniques may not work because of the infinitesimal output current. However, the different power losses of each cell would lead to the individual DC voltages unbalance. The uneven power losses on the local supplied cell-controllers (including the control circuit and drive circuit) would especially cause the divergence of individual DC voltages, due to their characteristic as constant power loads. To solve this problem, this paper proposes an adaptive voltage balancing module which is designed in the cell-controller board with small size and low cost circuits. It is controlled to make the power loss of the cell a constant resistance load, thus the DC voltages are balanced in zero current mode. Field test in a 10kV STATCOM confirms the performance of the proposed method.

• 한국표면공학회지
• /
• 제43권6호
• /
• pp.283-288
• /
• 2010

Ni-$TiO_2$ nano composite coatings were fabricated using pulse current electrodeposition technique at 100 Hz pulse frequency with a constant 50% pulse duty cycles and reference was taken with respect to the direct current (dc) electrodeposition. The properties of the composite coatings were investigated by using SEM, XRD, Wear test and Vicker's microhardness test. Pulse electrodeposited composite has exhibited enhancement of (111), (220), and (311) diffraction lines with an attenuation of (200) line. The results demonstrated that the microhardness of composite coatings under pulse condition was significantly improved than that of pure nickel coating as well as dc electrodeposited Ni-$TiO_2$ composite coatings. Wear tracks have shown the less plastic deformation in pulse plated composite. Coefficient of friction was also found to be lower in pulse plated composite coatings as compared to dc plated composite coatings.

• 조명전기설비학회논문지
• /
• 제25권1호
• /
• pp.93-100
• /
• 2011

This paper presents a technical study for the first short stroke lightning current generator using a crowbar device. The so-called crowbar-technology is most common to make 10/350[${\mu}s$] impulse currents with high amplitude, and the lightning current generator with crowbar device has an economic advantage than the nominal RLC current generator. But both the operating efficiency and the operating reliability of crowbar spark gap are very important to design the current generator. So, the peaking circuit which consists of small capacitors and a spark gap is applied. And the multi-step coil for controlling the circuit constant at the different test conditions is used. The presented test facility is designed to perform impulse tests with amplitudes up to 50[kA] of 10/350[${\mu}s$].

• 한국전자통신학회논문지
• /
• 제13권1호
• /
• pp.85-92
• /
• 2018

본 논문에서는 $-40^{\circ}C$에서 동작하는 150W급 LED조명용 전원공급장치(SMPS) 회로를 설계하였다. SMPS의 특성 해석을 위해서 150W급 LED 조명 구동 정전류 회로를 설계하고 시제품의 제작 및 성능을 측정하였다. 150W급 LED조명용 SMPS 회로의 동작온도범위는 $-40{\sim}70^{\circ}C$이며, SMPS 예측 수명은 24시간 기준으로 1.29~2.25년으로 예측되었다. 초가속수명시험 및 EMI 전도 시험을 통해 이상이 없음을 확인하였다.

• 전력전자학회논문지
• /
• 제16권3호
• /
• pp.258-265
• /
• 2011

본 논문은 다이어프램의 공기압력을 제어하기 위한 가변 주파수 전류 제어기를 제안한다. 제안된 제어기는 기존의 다이어프램의 공기압력을 제어하는 방법과는 달리 단상 인버터를 이용하여 상 전류와 주파수를 제어한다. 한 상의 전류는 다이어프램의 지령 공기 압력을 추종하도록 조절되고, 전류 주파수는 기계적인 진동을 줄이기 위해 변화한다. 일정한 공기압력으로 부드럽게 변화하기 위해서 전류 주파수는 전류 제어기에서 제어전압에 따라 제어되며, 이 때의 상전류가 일정한 공기압력에 만족하게 되면 전류주파수는 다이어프램의 진동을 줄이기 위해 증가된다. 제어 전압에 의한 상 전류가 지령값보다 높게 되면 전류 주파수는 공기압력을 추종하기 위해 감소된다. 제안된 제어방식은 상용 다이어프램을 이용한 실험을 통해 확인하였다.

• Journal of Welding and Joining
• /
• 제14권6호
• /
• pp.48-57
• /
• 1996

The weldability of high purity aluminum-lithium binary alloys has been investigated using the Varestraint test. Autogenous GTAW (gas-tungsten-arc-welds) were run along specimens of different lithium concentration using three sets of welding parameters. Welding voltage was held constant at 10 volts. Welding current (70∼100 amps) and travel speed (23∼33 cm/min) were the parameter varied. Hot-tearing susceptibility varied with lithium content and exhibited a steep peak at 2.6 weight percent lithium. Depth of penetration increased with increasing heat input and lithium concentration. The susceptibility is influenced by the wettability of dendrites by the interdendritic eutectic liquid as well as the time available for back-Siting by eutectic liquid. The welding condition of welding current 70A and travel speed 23 cm/min was showed good resistance to cracking in aluminum-lithium alloys. Suggestions for improving weld cracking resistance are also provided.