• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.75-82
• /
• 1990

To study on the behavior of the early stage of the spark kernel at constant pressure condition, the expressions of the thermal properties such as compressibility factor, thermal conductivity, and electrical conductivity of the high temperature air were newly suggested. The newly suggested simple expressions of the thermal properties of the high temperature air showed good results. Under the assumption of constant pressure, one dimensional numerical analysis was executed by varying surrounding conditions and discharging current of electrical spark. Numerical results show tat high surrounding pressure suppresses the growth of the spark kernel but supplies much electrical energy into the air, on the other hand high surrounding temperature increases the growth of the spark kernel but supplies less electrical energy. Also the result shows that , in case of direct current discharge, deposited electrical energy is able to be expressed in linear function of time approximately.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.1
• /
• pp.81-85
• /
• 1996

Microwave dielectric properties of 0.15(B $a_{x}$S $r_{0.05}$)O-0.15(S $m_{2}$(1-y)N $d_{2y}$) $O_{3}$-0.7Ti $o_{2}$(x=o.9~0.1[mol.], y=6[m/o]) ceramics were investigated with BaO compositional ratio. Sintered density and resistivity of specimens were independent on the BaO compositional ratio. In the specimen with x=0.975[mol.], dielectric constant, quality factor and temperature coefficient of resonant frequency had good values of 76.52, 3001(at 3[GHz]) and +0.71[ppm/.ceg. C], respectively. By comparing with the stoichiometric compositions of 78.14, 2938(at 3[GHz])+14.19[ppm/.ceg. C], dielectric constant and quality factor showed similar properties, but the temperature coefficient of resonant frequency was highly improved. (author). refs., figs., tabs.s.s.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.391-397
• /
• 2006

The soot yield has been studied by a premixed propane-oxygen-inert gas combustion in a specially designed disk-type constant-volume combustion chamber to investigate the effect of pressure, temperature and turbulence on soot formation. Premixtures are simultaneously ignited by eight spark plugs located on the circumference of chamber at 45 degrees intervals in order to observe the soot formation under high temperature and high pressure. The eight converged flames compress the end gases to a high pressure. The laser schlieren and direct flame photographs with observation area of 10 mm in diameter are taken to examine the behaviors of flame front and gas flow in laminar and turbulent combustion. The soot volume fraction in the chamber center during the final stage of combustion at the highest pressure is measured by the in-situ laser extinction technique and simultaneously the corresponding burnt gas temperature by the two-color pyrometry method. The changes of pressure and temperature during soot formation are controlled by varying the initial charging pressure and the volume fraction of inert gas compositions, respectively. It is found that the soot yield increases with dropping the temperature and raising the pressure at a constant equivalence ratio, and the soot yield in turbulent combustion decreases as compared with that in laminar combustion because the burnt gas temperature increases with the drop of heat loss for laminar combustion.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.111-117
• /
• 2001

The temperature dependence of dielectric constant and electrical conductivity for the BBPS glasses system was studied over a temperature range between $30^{\circ}C$ and $500^{\circ}C$ and at a frequency ranged from $10^3$ Hz to $10^7$ Hz. The dielectric constant ${\varepsilon}$ at room temperature of $xB_2O_3-yBi_2O_3-zPbO-5SiO_2 $ glasses was measured to be 15 at $10^5$ Hz for all samples and found to be almost frequency independent. At the relatively low temperature ranger (<$70^{\circ}C$), the dielectric constant was almost temperature independent and above that it increased with increasing temperature: the rate of increase being different at different frequencies. This behavior could be explained on the basis of the presence of molecular dipoles. The dielectric constant was found to depend on the composition as well as the crystalline phases formed in the glass matrix.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.260-268
• /
• 2006

The dielectric constants of used gasoline engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$ Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz,,and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 4% for gasoline engine oil.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.290-300
• /
• 2006

The dielectric constants of used diesel engine oils were obtained at a few temperatures and a frequency. Through analyzing the characteristics of dielectric constant, the related correlation between the changes in dielectric constants of oil and the degree of oil deterioration is going to be found. The dielectric constant was calculated using cross capacitances measured by a sensor tube. As results of the measurement of the fresh engine oil's dielectric constant, it was found that the value of dielectric constant was set down below $60^{\circ}C$ regardless changing frequency. Further, above 6 kHz, the dielectric constant was set down even if temperature was above $100^{\circ}C$. Therefore, for the measurement of used oils, it was selected the frequency of 6 kHz, and the temperature of $80^{\circ}C$ preventing a certain ionic-conduction effects on the measured dielectric constant and the evaporation of a certain fluid mixed with engine oil. Specially, the effects of the mixing fluid like coolant, water and fuel on the fresh engine oil's dielectric constant were studied. It was found that the oil mixed with coolant showed the highest value, next water, and the lowest fuel. As results of the measurement of the used engine oil's dielectric constant, it was found that the possible changed rate of the used engine oil's dielectric constant based on the warning limit for engine oil in service was below 10% for diesel engine oil.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.9
• /
• pp.1239-1246
• /
• 2000

The objective of this work is to measure space and time resolved wall heat fluxes during nucleate pool boiling of R113/R11 mixtures using a microscale heater array in conjunction with a high speed CCD. The microscale heater array is constructed using VLSI techniques, and consists of 96 serpentine platinum resistance heaters on a transparent quartz substrate. Electronic feedback circuits are used to keep the temperature of each heater at a specified temperature and the variation in heating power required to keep the temperature constant is measured. Heat flux data around an isolated bubble are obtained with triggered CCD images. CCD images are obtained at a rate of 1000frames/second. The heat transfer variation vs. time on the heaters directly around the nucleation site is plotted and correlated with images of the bubble obtainedby using the high speed CCD. For both of the mixture(R11/R113) and pure system(pure R11, pure R113), the wall heat fluxes are presented and compared to find out the qualitative difference between pure and binary mixture nucleate boiling.

• Electrical & Electronic Materials
• /
• v.10 no.10
• /
• pp.1005-1010
• /
• 1997

ZnS:Mn thin film was made by coevaporation with Electron Beam Evaparation(EBE) method. And structural and optical characteristics of ZnS:Mn thin films were investigated by substrate temperature annealing temperature and dopant Mn. When ZnS:Mn thin film was well deposited with cubic crystalline at substrate temperature of 30$0^{\circ}C$ its surface index was [111] and its lattice constant of a was 5.41$\AA$. Also When ZnA:Mn thin film was well made with hexagonal crystalline at substrate temperature of 30$0^{\circ}C$annealing temperature of 50$0^{\circ}C$and annealing time of 60min its miller indices were (0002) (1011), (1012) and (1120). And its lattice constant of a and c was 3.88$\AA$and 12.41$\AA$ respectively. Finally hexagonal ZnS:Mn thin film with dopant Mn of 0.5wt% had fundamental absorption wavelength of 342nm. And so its energy bandgap was about 3.62eV.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.123-126
• /
• 2001

The $0.98MgTiO_3-0.02BaTiO_3$ ceramics were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature and composition ratio by XRD, SEM and EDS. According to the X-ray diffraction patterns of the $0.98MgTiO_3-0.02BaTiO_3$ ceramics, the hexagonal $BaMg_6Ti_6O_{19}$ and ilmenite $MgTiO_3$ structures were coexisted. The dielectric constant$({\varepsilin}_r)$ and quality factor$(Q{\times}f_r)$ were decreased with increasing the sintering temperature in the range of $1275^{\circ}C{\sim}1350^{\circ}C$. In the case of the $0.98MgTiO_3-0.02BaTiO_3$ ceramics sintered at $1275^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 20.27, 76,845, $-46.6ppm/^{\circ}C$, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.1
• /
• pp.9-16
• /
• 2012

This paper describes a measuring apparatus that can be used to appraise the effectiveness of nanofluids as new heat-transfer-enhancing fluids. A couple of apparatuses using fine hot wires as sensors have been proposed for this purpose; however, they have a technical weakness related to the uncertain working conditions of the sensor. The present method uses the convective heat transfer coefficient from a hot wire as an indication of the heat transfer effectiveness of the nanofluid, where the temperature of the wire remains constant during the experiment. The operating principle and experimental procedure are explained in detail, and the validity of the system is tested with pure base fluids. The effects of particle concentration, velocity, and temperature on the heat transfer coefficients of the nanofluids are discussed comprehensively using the experimental data for graphite nanolubrication oil.