• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.12
• /
• pp.660-667
• /
• 2013

This study presents a numerical investigation of the heat and mass transfer kinetics of a fin-tube-type adsorption bed using a two-dimensional numerical model with silica-gel and water as the adsorbent and refrigerant pair. The performance is strongly affected by the heat and mass transfer in the adsorption bed, but the details of the mass transfer kinetics remain unclear. The validity of inter-particle models used to simulate mass-transfer kinetics were examined, such as a constant pressure model and non-constant pressure model, and the valid ranges of the diffusion ratio for each model are proposed. The COP and SCP have been numerically calculated as the performance indexes according to the diffusion ratio. The constant pressure model, which is commonly used in previous research, was found to be valid only in a limited range of diffusion ratio.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.223-229
• /
• 2002

Spark plug ionization signal could be useful in an internal combustion engine as a feedback signal for combustion diagnostics such as misfire detection, knocking detection and lambda control, but the signal has high level of cyclic fluctuation in an internal combustion engine due to residual gas, pressure, temperature, mixture composition in the spark gap. Because of this reason it is very difficult to apply ion signal to commercial engine control. In this Study, a correlation between A/F and spark plug ionization signal was studied in a constant volume chamber. Constant volume chamber with gas phase fuel(Propane) has homogeneous fuel composition , no mixture flow, same pressure and temperature on each test. The results show that mean chemi-ion signal has the highest correlation with A/F and intial pressure change has on effect on the thermal-ion signal and not on chemi-ion signal.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.693-699
• /
• 2000

Casting behavior of Zr(Y,Ce)O2 TZP/Mullite suspension during pressure filtration was investigated to prepare multi-layered Functionally Gradient Materials(FGM). The dispersion stabilities of each layer suspension were investigated by examination of zeta potential and viscosity. The each suspensions with 20 vol.% solid loading and 100 첸 of viscosity was prepared after fix of the dispersing agent (Sodium hexa-meta phosphate) and the binder (Hydroxyethyl cellulose), and then the cakes were formed at the 2.5 MPa~10.0MPa pressure range. The cake thickness of all suspensions was increased with the square root of time at the constant pressure, and the relations between filtration pressure(P)a nd dehydration rate (Q=dh/dt) showed that the flows of filtrates in the consolidated layers were laminar. The permeabilities were nearly constant during filtration, and kozeny constants(Kc) of the suspensions were 4.8~6.7. These valumes were seen as close to 5, which might be homogeneous particle packing during filtration. On the basis of those data, the multi layered compaction with 9 mm thickness and 52.5% green density was prepared by continuous pressure filtration.

• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.3
• /
• pp.81-90
• /
• 1988

In recent, the requirement of remote control of hychaulic system is in- creasing. The actuator unit whose output position is proportional to input electrical signal needs a pressure reducer and a dump valve. The pressure reducer provides a constant regulated pressure and filters contaminants. The dump valve supplies proper pressure to the pressure reducer and unloads when the system is not operated. In this thesis, dump valve and pressure reducer with auxiliary function are studied. The choke in the pressure reducer prevents actuator from supplying higher pressure than necessary pressure at beginning, and the spring constant affects on the dynamic characterisics. In dump valve, it is proved that diameter of servo-slide hold and choke diameter of dump plunger affects on damping response.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.10
• /
• pp.704-709
• /
• 1999

The optical properties such as luminance and color coordinates for phosphor layer were studied with applied voltage and gas pressure, Xe mixing ratio, frequency using He and Xe mixing gas in chamber like AC PDP. The luminance of red phosphor layer at constant pressure(300Toor) is increased with increasing voltage, but color purity is not varied. The luminance of red phosphor layer at constant voltage(280V)is decreased with increasing pressure, but the color purity is not varied. But the luminance is increased with increasing Xe mixing ratio at constant pressure(200Toor). And also the color purity is improved by this process. The luminance is increased up to 40kHz, but the color purity with frequency is not varied.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.6
• /
• pp.429-433
• /
• 2013

PTFE composites for use of microwave substrate were fabricated by impregnation and heat treatment fabrication with glass fabric. This study shows dielectric properties such as dielectric constant and loss can be controlled by thickness of PTFE composite with change of pressure condition in heating press process. The dielectric constant of the PTFE composites has decreasing tendency as given higher pressure condition. The dielectric loss has similar result too. Especially, the case of the dielectric loss was affected by the condition of pressure at heating press and had the best performance under 3 MPa. In order to see the reason why thickness conditions make different, their microstructures were also observed.

• Journal of the Korean Society of Combustion
• /
• v.13 no.3
• /
• pp.9-16
• /
• 2008

In this study, a cylindrical constant volume combustion chamber is used to investigate the flow and combustion characteristics of methane-air homogeneous mixture under various initial charge pressure, excess air ratios and ignition times. The flame and burning speed, mean gas speed are calculated by numerical analysis to analyze the combustion characteristics. It is found that the mean gas velocity during combustion has the maximum value around 300 ms and then decreased gradually on the condition of 10000 ms, and that the combustion duration is shorten and flame speed and burning velocity have the highest value under the conditions of an excess air ratio 1.1, an initial charge pressure of 0.2 MPa and an ignition time of 300 ms in the present study. And, the initial pressure and burning speed are in inverse proportion, so that it is in agreement with Strehlow who presented that the initial pressure and burning speed are in inverse proportion when the burning speed is under 50cm/s.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.7
• /
• pp.1082-1091
• /
• 2004

Analyzed Parametrically was an internal combustion engine combined with gas turbine the cycle of which is splitted into compression side cylinder and expansion side one, and heat adding of which is during constant volume pressure, temperature process. The advantages of each measures were analyzed by means of thermal cycle diagram. The thermal efficiency of partial load cutting off firstly isothermal heat adding and secondly isobaric heat adding also was analyzed The authors suggested some potentials about the performance as for thermal efficiency, mean effective pressure and reducing emissions and noise supposed were the operating parameter of the engine set to some values and were some problems solved.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.1 s.106
• /
• pp.34-39
• /
• 2006

For the evaluation of the normalized impact sound pressure level, the reverberation time of the receiving room should be measured. This paper deals with the effect of the time constant of FFT analyzer and the measuring points on reverberation time. It is found that the time constant should be in the range between 10 ms and 35 ms. While the effect of measuring points on the reverberation time is significant when the bandwidth is narrow it is negligible in the evaluation of the normalized impact sound pressure level.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.75-82
• /
• 1990

To study on the behavior of the early stage of the spark kernel at constant pressure condition, the expressions of the thermal properties such as compressibility factor, thermal conductivity, and electrical conductivity of the high temperature air were newly suggested. The newly suggested simple expressions of the thermal properties of the high temperature air showed good results. Under the assumption of constant pressure, one dimensional numerical analysis was executed by varying surrounding conditions and discharging current of electrical spark. Numerical results show tat high surrounding pressure suppresses the growth of the spark kernel but supplies much electrical energy into the air, on the other hand high surrounding temperature increases the growth of the spark kernel but supplies less electrical energy. Also the result shows that , in case of direct current discharge, deposited electrical energy is able to be expressed in linear function of time approximately.