• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1439-1447
• /
• 1994

Test results of friction-factor for the flow of air in a narrow channel lined with various honeycomb geometries show that, generally, the friction-factor is nearly constant or slightly decreases as the Reynolds number(or Mach number) increases, a characteristic common to turbulent flow in pipes. However, in some test geometries this trend is remarkably different. The friction factor dramatically drops and then rises as the Mach number increases. This phenomenon can be characterized as a "friction-factor jump." Further investigations of the acoustic spectrum indicate that the "friction-factor jump" phenomenon is accompanied by an onset of a normal mode resonance excited coherent flow fluctuation structure, which occurs at Reynolds number of the order of $10^4$. New empirical friction-factor model for "friction-factor jump" cases is developed as a function of Mach number and local pressure.ach number and local pressure.

• 동력기계공학회지
• /
• 제17권1호
• /
• pp.64-70
• /
• 2013

The heat transfer and friction factor characteristics of turbulent flows in three stationary channels have been investigated experimentally to check out the effect of divergence ratio. These are a constant cross-sectional channel and two diverging channels with ratio of divergence(Dho/Dhi) of 1.16 and 1.49. The measurement was conducted within the range of Reynolds numbers from 15,000 to 89,000 and the dimension of uniform cross-sectional test section is $100mm{\times}100mm$ at the cross section and 1,000 mm in length. The measurements of heat transfer coefficients and friction factors in the uniform channels were conducted as a reference. Because of the streamwise flow deceleration, the heat transfer and friction factor characteristics in the diverging channel were quite different from those of the constant cross-sectional channel. The effective friction factors and convective heat transfer coefficients increased with increasing the ratio of divergence of the channel.

• 소성∙가공
• /
• 제3권2호
• /
• pp.215-228
• /
• 1994

The purpose of this paper is to pursue a general method to determine both the flow stress of a material and the friction factor by ring compression test. The materials are assumed to obey the expanded n-power hardening rule including the strain-rate effect. Ring compression is simulated by the rigid-plastic finite element method to obtain the database used in determining the flow stress and friction factor. The Simulation is conducted for various strain hardening exponent, strain-rate sensitivity, friction factor, and compressing speed, as variables. It is assumed that the friction factor is constant during the compression process. To evaluate the compatibility of the database, experiments are carried out at room and evaluated temperature using specimens of aluminum 6061-T6 under dry and grease lubrication condition. It is shown that the proposed test method is useful and easy to use in determining the flow stress and the friction factor.

• 한국해안·해양공학회논문집
• /
• 제22권2호
• /
• pp.73-78
• /
• 2010

파에너지는 쇄파되기 이전까지 주로 해저면과의 마찰력에 의하여 감소한다. 파마찰력을 산정하기 위한 연구는 여러 연구자들에 의해 진행되어 왔으며 어느 특정지점에서의 파마찰력 또는 파마찰손실률은 선형파이론으로 주어지는 해저면 입자유속과 연관된 파마찰계수의 도입으로 상당히 정확하게 간단하게 산정할 수 있다. 그러나 장구간에 걸쳐 파마찰력에 의하여 점차적으로 감소되는 파고변이는 상당한 반복 과정을 거쳐야 산정할 수 있었다. 본 연구에서는 기존 경험식을 이용해 전난류, 완난류 경우에 대해 일정경사면에서 천수효과와 마찰손실에 의한 파고 변화를 비교적 간단한 방법으로 추정하는 방법을 제시하였다. 해빈경사가 일정할 때 파고 변이률은 천수계수와 파고 마찰손실계수의 곱으로 간단히 구할 수 있다. 실제 해안과 비슷한 조건의 경우에 대하여 반복시산 과정으로 구한 수치와 간편 산정식으로 간단히 계산한 결과를 비교하여 제시하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.49-56
• /
• 1999

A material was formulated with Phenol novolac and HEXA only. The cure kinetics and thermal characteristics of phenol novolac with various HEXA contents were peformed by differential scanning calorimetry and thermal gravimetric analysis. All kinetic parameters of the curing reaction including the reaction order, activation energy, and rate constant were calculated and reported. The results indicate that the curing reaction goes through an autocatalytic kinetic mechanism. The friction and wear characteristics of this material were determined using friction material testing machine. The friction coefficient of phenol novolac with various HEXA contents was determined using the PV(pressure & velocity) factor. The most stable and highest friction coefficient with a various pressure and velocity condition was found at HEXA 10 wt.% material. The specific wear rate per unit sliding distance with a various HEXA contents was reported.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권5호
• /
• pp.58-67
• /
• 1996

In the present study, the pressure distribution, wall shear stress distribution and friction factor of developing turbulent pulsating flows are investigated theoretically and experimentally in the entrance region of a square duct. The pressure distribution for turbulent pulsating flows are in good agreement with the theoretical values. The time-averaged pressure gradients of the turbulent pulsating flows show the same tendency as those of turbulent steady flows as the time-averged Reynolds number $(Re_{ta})$ increase. Mean shear stresses in the turbulent pulsating flow increase more in the inlet flow region than in the fully developed flow region and approach to almost constant value in the fully developed flow region. In the turbulent pulsating flow, the friction factor of the quasi-steady state flow $({\lambda}_{q, tu})$ follow friction factor's law in turbulent steady flow. The entrance length of the turbulent pulsating flow is not influenced by the time-averaged Reynolds number $(Re_{ta})$ and it is about 40 times as large as the hydraulic diameter.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.445-449
• /
• 2009

With the recent increase in the demand for the net-shape forming, numerical simulations are being commonly adopted to increase the efficiency and effectiveness of design of bulk metal forming processes. Proper consideration of tribological problems at the contact interface between the tool and workpiece is crucial in such simulations. In other words, lubrication and friction play important roles in metal forming by influencing the metal flow, forming load and die wear. In order to quantitatively estimate such friction condition or lubricant characteristic, the constant shear friction model is widely used for bulk deformation analyses. For this, new friction testing method based on the forward or backward extrusion process is proposed to predict the shear friction factor in this work. In this method, the tube-shaped punch pressurizes the workpiece so that the heights at the center and outer of punch (or mandrel) become different according to the friction condition. That is, the height at the center of punch is higher than that at the outer of the punch when the friction condition at the contact interface is severe. From this founding, the proposed friction testing method can be applied to effectively evaluate the friction condition in bulk metal forming processes.

• 대한기계학회논문집A
• /
• 제38권12호
• /
• pp.1317-1323
• /
• 2014

본 연구의 목적은 마찰교반용접된 Al7075-T651의 피로균열전파 거동에 미치는 시험편의 채취방향의 영향을 고찰하기 위한 것이다. 피로균열전파 실험은 마찰교반용접된 공시재로부터 모재와 용접재에 대하여 CT 시험편을 채취하여 일정응력확대계수범위 제어하에서 수행되었다. 균열이 용접선에 수직하여 전파하는 것(TL 시험편으로 명명)과 균열이 용접선과 나란히 전파하는 시험편(LT 시험편으로 명명)에 대하여 3가지 다른 응력확대계수범위에서 실험이 수행되었다. 시험편의 채취 방향에 따라 피로균열전파거동에 주요한 영향을 미침을 알 수 있었다. Paris 법칙에 적합시킨 결과 지수 m값은 WM-LT 시험편이 3.56으로 가장 높게 나타났다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.830-832
• /
• 2014

In this study, friction stick-slip vibration're interpretation of the phenomenon, we used a statistical model of friction. In a previous study using a definite friction factor, but to a dynamic simulation using a constantly changing during the integration time by a Monte Carlo simulation method, not the average coefficient of friction and the dynamic friction coefficient and a constant value in this study.

• 설비공학논문집
• /
• 제4권3호
• /
• pp.155-162
• /
• 1992

Theoritical Study is performed on heat transfer and fluid flow induced by square-ribbed roughness elements in a concentric annulus. The fluid properties were assumed to be constant, and the radius($r_m$) of the maximum speed point was found by using the principle of equation of Leung and Labib. The Nusselt number and friction factor as a function of the Reynolds number($R_e=10^4$, $5{\times}10^4$, $7{\times}10^4$, $10^5$) in artifical roughness $S/{\epsilon}=5,10,20,30$, $P/{\epsilon}=2,5,8$ and prandtl number = 0.72 have been discussed. In this study, it has been found that the Nusselt number and friction factor of rough wall are larger than those of smooth ones.