• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.44-50
• /
• 2002

The connecting rod big-end bearing is one of the most heavily loaded components of the lubrication system of high-speed combustion engines. The supply oil flow has to pass to the main bearing and the rotating crankshaft before entering the connecting rod bearing. It is common knowledge that the centrifugal forces due to the crankshaft rotation influence the oil flow to connecting rod bearing through the oil supply bore, especially, when the oil supply system to the connecting rod bearing has a 180$^{\circ}$circumferential groove via a single drilling in the crankshaft. In this case, it should be confirmed that the groove oil pressure in the main bearing is sufficient to overcome these centrifugal forces. For the purpose, the dynamic oil pressure before entering oil supply bore to the connecting rod bearing was measured instead of averaged oil pressure in main gallery. Experimental test results show that the dynamic oil pressure in the oil groove was more useful than that of main gallery. And it was also found that the oil pressure fluctuation in the groove was sensitively affected by the reduction of the main bearing clearance.

• 한국정밀공학회지
• /
• 제16권4호통권97호
• /
• pp.79-84
• /
• 1999

This paper focus on investigating the influence of the amount of water ingestion and the engine speed on the joint reaction force of the connecting rod in engine. The connecting rod was modelled by MSC/PATRAN, the modal informations of it were obtained by the DMAP module in the MSC/NASTRAN, and the dynamic force history was computed through the flexible multibody dynamic simulation in DADS. To analyze the joint reaction force acting on the connecting rod, the 48 cases were investigated. The engine speed varies with 200, 700, 1600, 2400rpm and the volumetric ratio of water to the combustion chamber varies with 0, 10, 20, ..., 90, 95 and 97.5% . As the engine speed decreases and the amount of water ingestion increases, the joint reaction force increase. Especially when the amount of water ingestion exceeds the 70% of the volume of the combution chamber, the joint reaction force acting on the connecting rod is over the design strength.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권1호
• /
• pp.118-124
• /
• 2017

본 연구대상 디젤기관의 연접봉 볼트, 크랭크 핀 베어링 볼트 등의 손상원인을 조사 분석하기 위하여 수행한 현장검사, 파손부에 대한 시험 및 고찰, 참고문헌 및 연구자의 경험 등을 통하여 다음과 같은 결론을 얻었다. 파손된 크랭크 핀 베어링 볼트는 연접봉 볼트보다 늦게 파손된 것으로 추정된다. 파손된 연접봉 볼트는 충격적인 하중에 의해서 취성파괴된 것이 아니고, 비정상적인 반복하중(예를 들어 체결 볼트의 풀림 등)에 의해서 피로파괴가 되었다는 것을 그 파단면의 모습을 통하여 알 수 있다. 파손된 연접봉 볼트용 U 너트는 윤활유(고착방지제)의 부적절한 사용, 각 실린더와 연접봉 별로 구분되어 사용되지 않았던 것 등으로 인하여 표면 상태가 불량하게 되었고, 이것은 연접봉 볼트의 파손사고에 영향을 미쳤을 가능성이 있다고 할 수 있다. 그리고 파손된 국내 제작품인 연접봉 볼트와 크랭크 핀 베어링 볼트의 기계적 성질, 전조공정 등은 해당 볼트의 설계요건에 적합하다고 할 수 있다.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.142-147
• /
• 2014

Finite element analysis along with DOE scheme has been performed to obtain robust design of connecting rod assembly. An analysis was conducted with five loading steps. Fatigue analysis was done using commercial software FEMFAT and fatigue safety factors at the interested regions such as shank area of small end and big end were calculated. 27 design cases using 3 factors with 3 levels are constructed by design of experiment. Each case is simulated to find the most influential factors. Response for this study, maximum Von-Mises stress, has been used to determine main factors of connecting rod assembly. Among the 3 factors, compression load affected the response greatly. However, bolt assembly load and width of shank flat area showed a little influence to the response. Interaction effects among factors considered did not occur. Connecting rod assembly considered in this study showed its sensitivity to the noise factor such as compression load rather than design factor such as width of flat shank area.

• 한국자동차공학회논문집
• /
• 제24권6호
• /
• pp.716-723
• /
• 2016

A connecting rod is a crucial part for transmitting an explosive force to the crankshaft in the engine. Stress concentration in connecting rod due to the accumulation of the repeated load may initiate micro crack and result in a crucial break down of the component. Two approaches are adopted to obtain a robust design of connecting rod. Inner and outer array matrix based on combinations of control factors and noise factors are constructed for using Taguchi method. Calculated stress results for each element of matrix are plotted in the Goodman diagram. Robust design approach by Taguchi method reduces stress concentration occurred in small end fillet area of the default model. Variable stress approach using Goodman diagram also confirms a robust design by Taguchi method.

• 열처리공학회지
• /
• 제19권3호
• /
• pp.163-169
• /
• 2006

Fretting is a kind of surface degradation mechanism observed in mechanical components and structures. The fretting damage decreases into 50-70% of the plain fatigue strength. The connecting rod for automobile has been used in special environments and various loading conditions. Failure of connecting rod in automotive engine may cause catastrophic situation. In this study, we investigated the fatigue characteristic of connecting rod material for an automobile. Fatigue life is defined as the number of cyclic stress to failure by regular cyclic stress. Fatigue life of C70S6 specimen was obtained from 134,000 to 147,000 cycles. Fatigue limit showed 432MPa by normal fatigue test. The other hands, it was 96MPa in the case of fretting fatigue test. It was extremely lower than that of a normal fatigue test. From observation of fracture surface, it was confirmed that the fatigue crack was initiated at the boundary of a specimen and bridge pad.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.794-798
• /
• 1995

We performed analysis for crank shaft and connecting rod in driving device of Cold Heading Machine. The results of this study is following ; 1. The nominal pressure is happened at 8mm under bottom dead center. And then the theoretical angel of crank (.theta.) and connecting rod (.phi.) are .theta. = 25 .deg. 1' and .phi.= 6 .deg. 1' but the analysis angel are .theta. = 25 .deg. and .phi.= 7 .deg. 2. The load is loaded at theta. = 51 .deg. in crank angle. 3. The maximum stress of connecting rod is about290MPa. It is exited inner stress range in consideration of safety factor.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.393-398
• /
• 2001

This paper aims to work process of connecting rod die using CAD/CAM/CNC systems. CAD/CAM/CNC systems are consist of CAD(MDT4.0), CAM(Z-MASTER) software and CNC milling machine. CAM software is purpose to G-code generation for CNC programming. Then CAM software and CNC milling machine are connect to RS-232-C cable for data network.

• Tribology and Lubricants
• /
• 제14권3호
• /
• pp.39-45
• /
• 1998

Reynolds equation, which describes behavior of fluid film in journal bearings, basically satisfies mass conservation. But, boundary conditions usually used with this equation, e.g. half Sommerfeld or Reynolds boundary conditions, cannot fulfill this natural law of conservation. In the case of connecting rod bearing, where applied load is dynamic and its magnitude is relatively large, such unrealistic boundary conditions have serious influence on calculation results, especially on lubricant flow rate or power disspation which are important parameters in thermal analysis. In this paper, mass-conserving boundary condition was applied in the finite element analysis of connecting rod bearings. Lubricant flow rate and power dissipation rate were calculated together with journal center locus, minimum film thickness and maxmium film pressure. These computation results were compared with those of the case of Reynolds boundary condition. Balance between inlet and outlet flow rate was well achieved in the case of mass-conserving boundary condition.

• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.319-325
• /
• 2007

Preload of critical engine bolts affects the performance and durability of engines. In modern engines that pursue higher power outputs and which are of lighter weight, it becomes more difficult to select an optimal target preload in consideration of various factors such as the role and structural characteristics of joint members, joint load, and fatigue durability of bolts and joint members. A procedure to select the bolt preload using computer-aided engineering technology, especially the finite element method, has been developed. The procedure is illustrated with connecting-rod bolts for which an appropriate preload is known. The selection criteria of target preload and the finite element modeling technique for connecting-rod bolts are also explained.