• Journal of Biosystems Engineering
• /
• 제6권1호
• /
• pp.48-59
• /
• 1981

The major limiting factor on the determination of combine capacity is the frequent occurence of clogging over the some parts of machine when the crop is wet in the case of Japanese self-feeding type combine. And in the case of American conventional combine having big separating parts, the great grain loss and damage occur when the machine is used for rice harvesting. This experiment was carried out to develop the new type threshing and separating equipment. Proto-type thresher which consist of a conical threshing drum and a conical separating sieve rotating around the threshing cone was constructed and tested. In the case of 800 rpm of threshing cone speed, average threshing loss was below 1 percent, separating loss was about 1 percent, grain damage was about 0.4 percent, and average total power required was about 2.6 PS. This design has some problems such as higher power required or wrapping problems under the conditions of feeding long damp straw. But, compared with the conventional combine or thresher, this machine certainly has some potentials for this approach to combine development. The crop feed rate must be increased through improvement of the feeding portion of the threshing cone. And it is required to investigate further about some parameters causing wrapping phenomena.

• 한국의류학회지
• /
• 제36권8호
• /
• pp.791-801
• /
• 2012

We performed an assessment of wearing, purchasing, satisfaction, and the fit of brassieres according to body and breast type for college women to provide basic data on the manufacture of an ergonomic brassiere. The classifications of domed and conical breast type or projecting and conical breast type were unclear. Flat breast were dissatisfied with the shape of small and flat, and drooping breast were dissatisfied with the shape of big, projected, and drooping. In purchasing a brassiere, the majority of subjects were ignorant of their brassiere size, and over 80% of the subjects bought a brassiere without trying it on. Over 50% of those surveyed said they found it difficult to buy a well-fitted brassiere, particularly for the flat and drooping breast type. Over 70% of those surveyed wore a brassiere of 3/4 cup size, the slim body type wore a brassiere of 1/2 cup size; however, the obese body type wore a brassiere of full-cup size. The flat-breast or slim-body wore a brassiere of a thick pad type but projecting-breast or drooping breast wore brassiere of a thin pad type. Many of the subjects wore an unfitted brassiere in cup size and under bust size. In the classification of breast type, there were slight differences between the breast type that they recognized and the breast type that they were shown. There were distinctions in function, satisfaction, and fitness based on breast type. Therefore, the development of an ergonomic brassiere should considered the characteristics of breast type for fitness and comfort.

• 대한수학회보
• /
• 제30권2호
• /
• pp.223-228
• /
• 1993

In this paper, we use the Patterson-Sullivan measure and results of [H] to show that for a nonelementary discrete group of divergence type, the conical limit set .LAMBDA.$_{c}$ has positive Patterson-Sullivan measure. The definition of the Patterson-Sullivan measure for groups of divergence type is reviewed in section 2. The Patterson-Sullivan measure can also be defined for groups of convergence type and the details for that case can be found in [N]. Necessary definitions and results from [H] are given in section 3, and in section 4, we prove our main result.t.

• 복식
• /
• 제58권5호
• /
• pp.13-34
• /
• 2008

In Headgear and Ornaments for Diadem in the Period of the Three States there was Conical Cap(or Pointed Cap), Feathered Cap(Trim), and Crown[Tree-typed Diadem and Tree and Antler-typed Diadem] was excavated from the tombs. Feathered Trim is 5 types, Feathered Trim I-A, Feathered Trim I-B, Feathered Trim II-A, Feathered Trim II-B, Feathered Trim II-C in according to upper part of central insert plate style. Feathered Trim I-A, I-B, II-B type was general style that was found in most of the old tombs in ancient Silla, Gaya. Feathered Trim II-A type was excavated from the only Silla tombs and II-C type was excavated from Gaya tombs. The Ornaments for Diadem in Baekje was excavated from the tombs is adorned with a arranged leaf-stems on either sides and the flower-shaped. They were distinguished with the original mode of Goguryeo and ancient Silla at the time. Tree-typed Diadem is five part in according to the Mountain(;山)-typed piled up. Only one Mountain(;山)-typed one in three stand-up ornament(I-1 type), and three step one in three stand-up one(I-2 type), modification one (I-3 type), three step one of four and five stand-up ones(I-4 type), and four step one of four and five stand-up ones (I-5 type). Tree and Antler-typed Diadem is three part in according to the step of Mountain(; 山)-typed and cross-shaped of the upper part. Three one of three step one of Mountain(;山)-typed and two Antler- typed (II-1 type), cross-shaped one(II-2 type), four step one(II-3 type).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.31-34
• /
• 2004

A new extrusion process of the circular section product with helical fins could be developed by using rotating extrusion dies. The twisting of extruded product is caused by the twisted conical die surface connecting the die entrance section and the die exit section linearly. But, until now, because the process has used fixed extrusion dies, it needs high pressure in order to twist billet and form fin shape on the surface of billet. So, during extruding billet, in order not to twist billet, the extrusion dies is needed to rotate itself instead of twisting billet. And in order to rotate dies, the shape of inside contour of extrusion dies must have conical type with twisted Inclined die surface connecting the die entrance section and the die exit section linearly. The results of experiments show that, in spite of using twisted extrusion dies, twisting of the billet should not happen because of rotating dies in the opposite direction of twisting direction of billet during extruding billet, and, from the results, it shows that it can decrease the power of extrusion pressure and could prevent crack of teeth for fin forming.

• Wind and Structures
• /
• 제8권5호
• /
• pp.357-372
• /
• 2005

Mean and extreme pressure distributions on a large cantilevered flat roof model are measured in a boundary layer wind tunnel. The largest peak suction values are observed from pressure taps beneath conical "delta-wing type" corner vortices that occur for oblique winds, then the characteristics and causes of the local peak suctions are discussed in detail. Power spectra of fluctuating wind pressures measured from some typical taps located at the roof edges under different wind directions are presented, and coherence functions of fluctuating pressures are also obtained. Based on these results, it is verified that the peak suctions are highly correlated with the conical vortices. Furthermore, according to the characteristics of wind loads on the roof, an aerodynamic solution to minimize the peak suctions by venting the leading edges and the corners of the roof is recommended. The experimental results show that the suggested strategy can effectively control the generation of the conical vortices and make a reduction of 50% in mean pressures and 25% in extreme local pressures at wind sensitive locations on the roof.

• Nuclear Engineering and Technology
• /
• 제54권4호
• /
• pp.1421-1430
• /
• 2022

The computation of the solid angle and the detector efficiency is considering to be one of the most important factors during the measuring process for the radioactivity, especially the cylindrical γ-ray NaI(Tl) detectors nowadays have applications in several fields such as industry, hazardous for health, the gamma-ray radiation detectors grow to be the main essential instruments in radiation protection sector. In the present work, a generic numerical simulation method (NSM) for calculating the efficiency of the γ-ray spectrometry setup is established. The formulas are suitable for any type of source-to-detector shape and can be valuable to determine the full-energy peak and the total efficiencies and P/T ratio of cylindrical γ-ray NaI(Tl) detector setup concerning the truncated conical radioactive source. This methodology is based on estimate the path length of γ-ray radiation inside the detector active medium, inside the source itself, and the self-attenuation correction factors, which typically use to correct the sample attenuation of the original geometry source. The calculations can be completed in general by using extra reasonable and complicate analytical and numerical techniques than the standard models; especially the effective solid angle, and the detector efficiency have to be calculated in case of the truncated conical radioactive source studied condition. Moreover, the (NSM) can be used for the straight calculations of the γ-ray detector efficiency after the computation of improvement that need in the case of γ-γ coincidence summing (CS). The (NSM) confirmation of the development created by the efficiency transfer method has been achieved by comparing the results of the measuring truncated conical radioactive source with certified nuclide activities with the γ-ray NaI(Tl) detector, and a good agreement was obtained after corrections of (CS). The methodology can be unlimited to find the theoretical efficiencies and modifications equivalent to any geometry by essential sufficiently the physical selective considered situation.

• 대한치과보철학회지
• /
• 제41권4호
• /
• pp.393-404
• /
• 2003

Statement of problem. Higher incidence of prosthetic complications such as screw loosening, screw fracture has been reported for posterior single tooth implant. So, there is ongoing research regarding stability of implant-abutment interface. One of those research is increasing the implant diameter and prosthetic table width to improve joint stability. In another part of this research, internal conical type implant-abutment interface was developed and reported joint strength is higher than traditional external hex interface. Purpose. The purpose of this study is to compare stress distribution in single molar implant between external hex butt joint implant and internal conical joint implant when increasing the implant diameter and prosthetic table width : 4mm diameter, 5mm diameter, 5mm diameter/6mm prosthetic table width. Material and method. Non-linear finite element models were created and the 3-dimensional finite element analysis was performed to see the distribution of stress when 300N static loading was applied to model at $0^{\circ},\;15^{\circ},\;30^{\circ}$ off-axis angle. Results. The following results were obtained : 1. Internal conical joint showed lower tensile stress value than that of external hex butt joint. 2. When off-axis loading was applied, internal conical joint showed more effective stress distribution than external hex butt joint. 3. External hex butt joint showed lower tensile stress value when the implant diameter was increased. 4. Internal conical joint showed lower tensile stress value than external hex butt joint when the implant diameter was increased. 5. Both of these joint mechanism showed lower tensile stress value when the prosthetic table width was increased. Conclusion. Internal conical joint showed more effective stress distribution than external hex joint. Increasing implant diameter showed more effective stress distribution than increasing prosthetic table width.

• 생물환경조절학회지
• /
• 제29권1호
• /
• pp.36-42
• /
• 2020

본 연구에서는 국내에 가장 많이 보급되어 있는 1-2W 모델 연동온실에 대한 온실 규격 및 환기창 형태 실태 조사를 수행하고, 이를 바탕으로 연동온실의 천창 형태에 따른 유동 특성을 분석하기 위해 수치해석을 수행하여 자연환기효과를 분석하고자 하였다. 온실 실태조사 대상농가의 환기창면적 비율은 평균10%로 자연환기를 위한 시설면적 대비 환기창 면적 설계가 부족한 것으로 나타나 환기창 개선이 필요할 것으로 판단된다. 연동 온실의 천창 형태별 자연환기를 해석 및 분석한 결과, 온실 내 작물위치의 온도 분포 및 내외부 온도차는 몽골식 천창 온실에서 가장 낮고 외몽골식 천창 온실에서 가장 높게 나타났으나 추후 풍하중에 의한 구조적인 안전성을 평가해야할 것으로 판단된다.

• 한국어류학회지
• /
• 제24권4호
• /
• pp.247-252
• /
• 2012

한국산 송사리속 2종에 대한 섭이기관의 구조적 차이를 알아보기 위하여 악골 및 이빨 구조를 조사하였다. 악골에서 송사리 Oryzias latipes는 전상악골 중앙부의 등 쪽 가장자리에 움푹 들어가는 홈이 존재하였으나 대륙송사리 O. sinensis는 일직선이었다. 후반부의 위치에서 송사리는 중앙부와 일직선상에 존재하였으나 대륙송사리는 배 쪽에 존재하였다. 또한 송사리는 하악골의 구상돌기 아래로 이어지는 치골 뒷가장자리에 움푹 들어가는 홈이 존재한 반면에 대륙 송사리에서는 뒷가장자리가 일직선 모양을 하였다. 송사리는 성적이형으로서 수컷에서만 나타나는 큰 이빨이 하악골의 측면 방향으로 발달하였고, 대륙송사리는 등 쪽 방향으로 발달하였다. 한편 송사리의 이빨형태는 원뿔모양과 화살촉모양 2 types이 나타난 반면에 대륙송사리에서는 원뿔 모양 1 type만 나타나는 특징을 보였다. 이상과 같이 한국에 분포하는 2종의 송사리는 섭이기관에서 뚜렷한 종간의 특징을 잘 보여 주었다.