• 한국수소및신에너지학회논문집
• /
• 제19권2호
• /
• pp.163-170
• /
• 2008

Carbon nanofibers with nano-sized structures were evaluated as a active material using supercacitor electrode which could store electrochemical energy reversibly. A feasibility of EDLC electrode was estimated with specific surface area measurement by BET method and mesopore structure of carbon nanofiber surface could be explained electrochemical absorption-desorption in aqueous electrolyte. A capacitance of carbon nanofiber electrode was increased gradually, depending on the ratio of Ketjenblack as a conducting material. Ketjen Black $20{\sim}25\;wt.%$ ratio in electrode was observed a suitable amount of conducting material by cyclic voltametry results.

• 한국전기전자재료학회논문지
• /
• 제18권9호
• /
• pp.827-832
• /
• 2005

Dual band internal antennas were fabricated with Ag conducting paste of various preparation conditions and different print thickness by silk screen print. We have investigated microwave properties were compared Ag conducting paste antenna with copperplate antenna at 800 MHz and 1,800 MHz. Gain of Ag conducting paste antenna was improved when preparation conditions were the single size Ag particle, using dry type resin and high Ag containing percent. However, it was lower than that of copperplate antenna within $0.1\~2.0dBi$ at 800MHz. In addition, it was improved at 800MHz when thickness of Ag conducting paste was printed more than skin depth but it was held after critical print thickness. On the other hand, it was reached level of copperplate antenna at 1,800MHz.

• 한국전기전자재료학회논문지
• /
• 제15권2호
• /
• pp.153-161
• /
• 2002

Stable polyaniline-dodecylbenzenesulfonic acid(PANI-DBSA) fully dissolved in toluene was obtained by a direct one-step emulsion polymerization technique. By using the proper molar ratio of APS/aniline monomer and DBSA/aniline monomer, the highest conductivity(7 S/cm) of PANI was obtained. The UV-Vis absorption spectrum of PANI confirmed PANI is emeraldine salt form. PANI/styrene polymers (polystyrene and styrene-butadiene copolymer) blends were prepared by mixing PANI solution with polymers in toluene. These blends exhibited the conductivity of 10$\^$-4/-10$\^$-3/ S/cm at 1 wt. % of PANI content. The mechanical property of conducting blend was decreased and TGA thermograms of conducting blends were similar to that of PANI. It had been checked that the flatness of coating layers of conducting blends decreased with increasing conducting components. It was also found that the morphology of blends was setting closer to that of PANI at higher conducting component contents.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.497-500
• /
• 1997

Conducting polymer is new material in lithium secondary battery. conducting polymer has a lot of merit which is flexible and good handing so that this material is used battery system, solid polymer electrolytes airs used PEO(Polyethylene oxide) and PEO/PMMA branding material adding by liquid plasticizer or lithium salt polymer electrolyte which is added liquid plasticizer, lithium salt decreased the crystallity and thermal stability is over than 13$0^{\circ}C$. it is very useful tn apply lithium secondary battery system.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.155-159
• /
• 2003

The polypyrrole and polyaniline thin film sensors which were made by chemical polymerization were employed to detect ethanol gas. With a single sensor element we can obtain characteristic patterns of behaviour across a very wide frequency range when measuring either resistance or capacitance. Impedance spectroscopy was employed to study the gas sensing behavior of both capacitance and resistance based sensors with conducting polymer as the active sensing element.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.65-65
• /
• 2011

We report the application of conducting metal oxide electrodes for semiconducting metal oxide gas sensors. Pt interdigitated electrodes have been commonly used for metal oxide gas sensor because of the low resistivity, excellent thermal and chemical stability of Pt. However, the high cost of Pt is an obstacle for the wide use of metal oxide gas sensors compared with its counterpart electrochemical gas sensors. Meanwhile, relatively low-cost conducting metal oxides are widely being used for light-emitting diodes, flat panel displays, solar cell and etc. In this work, we have fabricated $WO_3$ and $SnO_2$ thin film gas sensors using interdigitated electrodes of conducting metal oxides. Thin film gas sensors based on conducting metal oxides exhibited superior gas sensing properties than those using Pt interdigitated electrodes. The result was attributed to the low contact resistance between the conducting metal oxide and the sensing material. Consequently, we demonstrated the feasibility of conducting metal oxide interdigitated electrodes for novel gas sensors.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1994년도 추계학술대회 논문집
• /
• pp.156-159
• /
• 1994

The electrical property of polyvinylalcohol (PVA) films (several hundreds ∼ several $\mu\textrm{m}$ in thickness) formed by sphere bulb blowing technique, has been studied. The electrical conductivity of relatively thick films (>several thousands ) has been very high and enhanced by the exposure either to high humidity fo air or NH$_3$. which can be explained in terms of the role of ionic transport. The use of PVA film as NH$_3$ sensor is also proposed. In PVA films less than 1500 , two conducting states: high conducting and low conducting states, are observed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.535-538
• /
• 2004

Zinc Oxide (ZnO) films have attracted considerable attention for transparent conducting films, because of their high conductivity, good optical transmittance from UV to near IR as well as a low-cost fabrication. To increase the conductivity of ZnO, doping of group III elements (Al, Ga, In and B) has been carried out. Transparent conducting films have been applied for optoelectric devices, the development of the transparent conducting thin films on flexible light-weight substrates are required. In this research, the transparent conducting ZnO thin films doped with Aluminum (Al) on polymer substrates were deposited by the RF magnetron suputtering method, and the structural, optical and electrical properties were investigated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.593-594
• /
• 2005

Lithium-ion batteries have used the layered $LiCoO_2$ materials as cathodes, but Co is relatively toxic and expensive. In this regard, the spinel $LiMn_2O_4$ has become appealing because manganese is inexpensive and environmentally benign. In general, cathodes for lithium ion batteries include carbon as a conductive agent that provides electron transfer between the active material and the current collector. In this work, we selected Acetylene Black and Super P Black as conducting agents, and then carried out comparative investigation for the performances of the cells using different conducting agents with different particle size. As a consequence, Li/$LiMn_2O_4$ cells with Super P Black show better electrochemical performances than those with Acetylene Black.

• Journal of Electrochemical Science and Technology
• /
• 제10권2호
• /
• pp.244-249
• /
• 2019

SiO has a high theoretical capacity as a promising anode material candidate for high-energy-density Li-ion batteries. However, its practical application is still not widely used because of the large volume change that occurs during cycling. In this report, an active material containing a mixture of SiO and graphite was used to improve the insufficient energy density of the conventional anode with the support of multidimensional conducting agents. To relieve the isolation of the active materials from volume changes of SiO/graphite electrode, two types of conducting agents, namely, 1-dimensional VGCF and 0-dimensional Super-P, were introduced. The combination of VGCF and Super-P conducting agents efficiently maintained electrical pathways among particles in the electrode during cycling. We found that the electrochemical performances of cycleability and rate capability were greatly improved by employing the conducting agent combinations of VGCF and Super-P compared with the electrode using only single VGCF or single Super-P. We investigated the detailed failure mechanisms by using systematic electrochemical analyses.