• Magazine of the Korea Concrete Institute
• /
• v.10 no.1
• /
• pp.161-169
• /
• 1998

프리스트레스트 콘크리트 교량의 건설공법인 프리캐스트 세그멘탈 공법에서선형관리 기술은 핵심기술 중 하나이다. 그럼에도 불구하고 , 우리나라에서는 몇몇 교량기술자들에게 경험적으로 이해되고 있는 수준을 넘지 못하고 있다. 특히, 세그멘트의 제작에서부터 반드시 필요한 선형관리용 S/W 및 그 운용기술은 아직까지도 선진기술에 의존하고 있는 실정이다. 본 연구에서는 프리캐스트 세그멘탈 공법의 선형관리 기술에 대한 연구를 통하여 3차원적인 세그멘트 제작관리와 가설시 선형관리를 위한 제작선형을 자동적으로 계산할 수 있는 GEOCON을 개발하였다. 본 논문에서는 GEOCON의 알고리즘에 대하여 논하였으며, 특히 수치예제로서 제작오차의 발생위치에 따라 교량선형에 미치는 영향을 분석하였다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.6
• /
• pp.1125-1146
• /
• 2018

Segment lining applied to the TBM tunnel is mainly made of concrete, and it requires sufficient structural capacity to resist loads received during the construction and also after the completion. When segment lining is design to the Limit State Design, both Ultimate Limit State (ULS) and Service Limit State (SLS) should be met for the possible load cases that covers both permanent and temporary load cases - such as load applied by TBM. When design segment lining, it is important to check structural capacity at the joints as both temporary and permanent loads are always transferred through the segment joints, and sometimes the load applied to the joint is high enough to damage the segment - so called bursting failure. According to the various design guides from UK (PAS 8810, 2016), compression stress at the joint surface can generate bursting failure of the segment. This is normally from the TBM's jacking force applied at the circumferential joint, and the lining's hoop thrust generated from the permanent loads applied at the radial joint. Therefore, precast concrete segment lining's joints shall be designed to have sufficient structural capacity to resist bursting stresses generated by the TBM's jacking force and by the hoop thrust. In this study, bursting stress at the segment joints are calculated, and the joint's structural capacity was assessed using Leonhardt (1964) and FEM analysis for three different design cases. For those three analysis cases, hoop thrust at the radial joint was calculated with the application of the most widely used limit state design codes Eurocode and AASHTO LRFD (2017). For the circumferential joints bursting design, an assumed TBM jack force was used with considering of the construction tolerance of the segments and the eccentricity of the jack's position. The analysis results show reinforcement is needed as joint bursting stresses exceeds the allowable tensile strength of concrete. This highlights that joint bursting check shall be considered as a mandatory design item in the limit state design of the segment lining.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.6
• /
• pp.59-65
• /
• 2009

The use of precast concrete segments facilitates quality control and reduces construction cost and period. However, as a construction method it has limited applicability, for it demonstrates structurally disadvantageous behaviors due to stress concentration and large displacement in the joint of assembled segments. This paper proposes a precast segment joint with improved structural performance, and experimentally assesses the structural performance of the proposed joint in terms of crack and failure modes, deformation, maximum load and displacement ductility. In consideration of constructability and structural performance, this paper suggests different types of joint with shear key, post tension and steel rods as variables, and performs a static loading test on them. The test results show that the performance of SGSP specimens is around 84% that of a monolithic specimen in terms of the maximum load, while their ductility behaviors are better than the monolithic specimen. This result confirms the improved structural performance and applicability of the proposed joint.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.5
• /
• pp.303-314
• /
• 2021

With the high quality/high stiffness/high strength of segment lining, segment lining is increasingly used as the final lining of the tunnel. Precast concrete lining has higher quality and strength than field concrete. Paradoxically, this contributes to greater damage to concrete in the event of a fire in a tunnel. In this study, tests were conducted to determine the fire resistance performance of segment linings according to fiber content in fire resistance methods using synthetic fibers such as PP fibers. As a result, it was confirmed that fire resistance performance required by the relevant project can be secured when using 1.5 kg/m³ of PP fiber. In addition, comparison of the results of PP fibers with PET, a similar synthetic fiber, showed better fire resistance performance than when PP fibers were used.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.2
• /
• pp.93-106
• /
• 2021

In general, segment lining tunnel refers to a tunnel formed by connecting precast concrete segments as a ring and connecting such rings to each other in the longitudinal direction of the tunnel. As the structural properties of the segment lining is highly dependent on the behavior of the segment joints, thus correct modelling of joint behavior is crucial to understand and design the segment tunnel lining. When the tunnel is subjected to ground loads, the segment joint behaves like a hinge that resists rotation, and when the induced moment exceeds a certain limit of the rotation then it may enter into non-linear field. In understanding the effect of the segment joint on the lining behavior, a moment-rotation relationship of the segment joint was explored based on the Japanese practice and Janssen's approach commonly used in the actual design. This study also presents a method to determine the rotational stiffness of joint refer to the bearing strength. The rotation of the segment joint was estimated in virtual design conditions based on the existing models and the proposed method. And the sectional force of the segment lining and joint were calculated along with the estimated rotation. As the rotation at the segment joint increases, the joint contact area decreases, so the designer have to verify the segment joint for bearing strength as well. This paper suggests a consistent method to determine the rotational stiffness and bearing strength of joints.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.39-42
• /
• 2006

Recently, more highly effective construction materials are needed for the reasonable and economical structure system is required as the construction structures become more multi storied, large-sized and diversified. That is to say, the highly qualified concrete, the molt universal construction material is positively promoted as a part of plan to establish the effective space according to the dead load of structures and diminish of segment profile and to build up the economic structures. In particular, it is tendency of that the study for high strength concrete increases and construction example of reinforced concrete (RC) using the high strength concrete partially increases. However, the high strength concrete has the problems such high brittleness and low ductility. Specially, for the high strength concrete, it has different strength from normal concrete as the internal temperature goes up steadily due to high heat of hydration by the quantities of highly level of cement, so the concrete which is mixed with various scible materials is used. This study conducted a basic experiment to conclude an adequate selection of materials and to calculate an optimal mixing proportion of those materials to produce High-strength concrete. And also we conducted an experiment to find out basic properties of this concrete such as slump-flow, strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.1031-1038
• /
• 2002

In this paper the erection method of the Seohae Bridge starter is presented. The erection method of starter for cable stayed bridge was changed from conventional bracket supported erection to heavy lifting supported directly by stays. There was the need to reduce the erection time drastically. The cost saving was obtained as a bonus.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.514-519
• /
• 1996

In this study, an investigation on the geometry control of the precast segmental method(PSM) was performed and GEOCON was developed. It is an interactive software to control the 3-dimensional geometry of precast segmental bridges during the construction progress. Specially, this paper emphasized that the fabrication stage of the precast segment is the most important for the geometry control in the PSM and also descussed about some problems which can be overlooked in developing and using the geometry control softwares by explaining the GEOCON's characteristics. GEOCON was successfully applied to the surrounding road of Pusan harbor.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.89-92
• /
• 2004

Precast Segmental method was developed in germany 1950's. This method has been adoptted in long span girder mainly owing to easy construction effect. But, so far, The limit exists that this method is constructed in a portion of span and hard conveyance and foundation. This study was performed to analysis behavior difference of two rectangular section girder, spliced girder that was jointed 5-sliced 0.8m segment and monolithic girder that was produced in one body 4m span.

• International Journal of Highway Engineering
• /
• v.14 no.4
• /
• pp.113-124
• /
• 2012

PURPOSES : In This study two different concrete barrier systems have been proposed to be established at the small vehicle driveway. One is for median barrier, and the other is for roadside barrier. METHODS : In order to determine the suitable shape of barrier, the impact parameters including vehicle weight, impact angle, impact velocity and impact level have been analyzed. The real crash test has been carried out with 0.9 ton and 2.5 ton vehicles, respectively by using the 2m segment type concrete barriers connected by steel plates that are totally 40m barrier systems. RESULTS : The numerical results obtained by LS/DYNA-3D software are compared with real crash tests from the viewpoints of vehicle stability, vehicle trajectory, occupant risk, etc. CONCLUSIONS : From the above results, the dynamic performance of proposed barrier systems satisfies the specification of Korean Code for roadside safety structures.