• Magazine of the Korean Society of Agricultural Engineers
• /
• v.32 no.E
• /
• pp.67-73
• /
• 1990

Many distress mechanisms in pavement are known to be caused by the poor mechanical properties of bituminous concretes. Among many mechanical properties, tensile strength is one of the more important indicates that represent the resistance of pavement to traffic loading. However, there has been no relationship established between the strength and distress mechanisms. Therefore, this study was conducted to evaluate a correlation between the tensile strength value and the intensity of distress in bituminous concrete. Distress data were collected from an extensive field investigation over 77km of a four-lane highway in South Carolina, USA, and from laboratory prepared specimens in two phases of study. Strength data were obtained from a total of more than 400 field cores taken from the same highway and from 640marshall specimens of surface course mixture prepared in the laboratory. These data were analyzed using statistical test techniques. It was found from statistical analyses that the tensile strength of bituminous concrete had a strong relation with the pavement condition in the field. In the analysis of rutting and stripping, low strength concrete showed a higher distress rate in the mixture, and mixtures under distress in the field showed obviously reduced strength values. Stripping was found to be the most significant distress mechanism that was correlated with low strength bituminous concrete. Rutting appeared more frequently in a low strength pavement section of the highway as a sign of failure due to traffic loading.

• International Journal of Highway Engineering
• /
• v.14 no.5
• /
• pp.21-29
• /
• 2012

PURPOSES: This study is to investigate the mechanical performance of the fiber reinforced lean concrete with respect to different types of fibers. METHODS: Increased vehicle weight and other causes from the exposed conditions have accelerated the deteriorations of road pavement. A new multi-functional composite pavement system is being developed recently in order to extend service life and upgrade the pavement. A variety of tests were conducted before and after hardening of the concrete. RESULTS: From the test results, it was found that the use of different types of fibers did not affect the compressive strength development. This might be due to the inherent property of the lean concrete. When steel fibers were used relatively greater flexural strength and flexural fracture toughness were developed. Also addition of fly ash by replacing a part of Portland cement the fracture toughness was slightly increased. CONCLUSIONS: It has been known that the addition of fibers and use of mineral admixture can be positively considered in the development of multi-functional composite pavement system as its required mechanical performance is obtained.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.245-251
• /
• 1999

The joint in the concrete pavement provides a control against transverse or longitudinal cracking at slab, which may be caused by temperature or moisture variation during or after hydration. Without control of cracking, random crack may cause more serious distresses and result in structural or functional failure of pavement system. Sometimes, joint itself, purposed to control crack, may cause a distresses in joint due to its inherent weakness in structural integrity. Thus, the load transfer capacity in joint is very important for serviceability and durability. The purpose of this dissertation was to develop an evaluation system at joints of jointed concrete pavement using finite element analysis was performed using ILLI-SLAB program with a selected variables which might affect fairly to on the performance of transverse joints. The most significant variables were selected from precise analysis. It was concluded that the variables which most significantly affect to pavement deflections are the modulus of subgrade reaction(K) and the modulus of dowel/concrete interaction(G), and limiting criteria on the performance of joints at JCP at 300pci, 500,000 lb/in. respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.611-616
• /
• 2013

Nowadays concrete pavement is increasing, since it is more durable than asphalt pavement. And the concrete pavement with lateral rain groove may induce high level of concrete whine noise as pure tone. In this paper, the design factor for good concrete whine noise is considered in view of tire pattern and structure design. In respect of tire pattern design, the tire having a cap tread with high center part stiffness and low shoulder part stiffness shows best concrete whine noise performance. And in respect of tire structural design, the tire with a thick center part of cap tread and low tread part stiffness show best concrete whine noise performance.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.635-642
• /
• 1997

This research focused on the development of concrete overlay and test, which was conducted at 88 Highway 105k, 2 lanes of 290 m. The field application test consists of 6 cm and 10 cm bonded concrete overlay and 25 cm unbonded concrete overlay, using the slag cement for opening lanes for traffic early. The overlay were placed in a day. The whole period of traffic closing wes 8 day and it was reopened to traffic after concrete overlay has cured for 3 day. 5 cracks were founded when the field test section was investigated after 1 month, but all these may not make significant problems to overlay because these initiated and growed at the same line of repair section. The rideability and skid resistance become much better like in the new pavement after overlay. The structural capacity against deflection was much. which were verified by FWD(Falling Weight Deflectometer). The field test section is being used in a good condition and the results of field application and pavement performance analysis are encouraging. This rehabilitation methods may be adopted in Korea after a more field performance verifications.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2001.10a
• /
• pp.111-114
• /
• 2001

This study is a fundamental research for recycling waste vinyl in asphalt concrete mixture for roadway pavement. The mixing method and proper content of waste polyethylene(PE) film were determined through preliminary mix design. This study used 2-type aggregate gradations and two-type waste PE films. The mixtures were applied for a test pavement on a rural road. Quality evaluation of the asphalt concrete confirmed that waste vinyl asphalt concrete was applicable to road pavement.

• International Journal of Highway Engineering
• /
• v.15 no.5
• /
• pp.47-55
• /
• 2013

PURPOSES : The purpose of this study is to investigate the optimal joint positions which can minimize distresses of concrete pavement containing box culvert with horizontally skewed angles. METHODS : The concrete pavement containing the box culvert with different skewed angles and soil cover depths was modeled by 3 dimensional finite element method. The contact boundary condition was used between concrete and soil structures in addition to the nonlinear material property of soil in the finite element model. A dynamic analysis was performed by applying the self weight of pavement, negative temperature gradient of slab, and moving vehicle load simultaneously. RESULTS : In case of zero skewed angle ($0^{\circ}$), the maximum tensile stress of slab was the lowest when the joint was positioned directly over side of box culvert. In case there was a skewed angle, the maximum tensile stress of slab was the lowest when the joint passed the intersection between side of the box culvert and longitudinal centerline of slab. The magnitude of the maximum tensile stress converged to a constant value regardless the joint position from 3m of soil cover depth at all of the horizontally skewed angles. CONCLUSIONS : More reasonable and accurate design of the concrete pavement containing the box culvert can be possible based on the research results.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.79-80
• /
• 2022

A method for repairing cracks using low-viscosity resins has been proposed as a construction method that can quickly repair roads from deterioration. However, when the viscosity of the epoxy resin is high, there is a limit in that it is difficult for the material to penetrate into microcracks and cracks in the concrete top plate. In this study, an epoxy thin-layer pavement repair method was developed using low-viscosity PMMA (Poly methyl methacrylate) to repair microcracks on the pavement surface and pavement layer and reinforce the pavement surface. Materials necessary for the thin-layer packaging method were developed, and performance was evaluated to meet the epoxy binder quality standards. As a result, all materials met the required performance.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.273-277
• /
• 1993

Fitigue behavior of soil-cement based pavement due to repeatitive traffic loads is studied. Finite element method is employed to analyze the pavement system including base, subbase, and soil layers. The calculated stresses are then used to evaluate the fatigue life of a pavement system. For the study is needed to determine accurately the fatigue characteristic of various soil-cement systems.

• Korean Journal of Construction Engineering and Management
• /
• v.9 no.6
• /
• pp.268-276
• /
• 2008

In highway construction projects, concrete pavement productivity has been challenged with constructors and decision-makers; at present there are few methods available to accurately evaluate the factors impacting on it. Any inefficient method to analyze it leads to the excessive schedule, higher rehabilitation costs, shorter service life, and reduction of ride quality. To implement these negative outcomes, constructors or decision-makers need a systematic tool that can be used to categorize the factors related to construction productivity. This paper applies multiple regression technique for productivity analysis of the Jointed Plane Concrete Pavement (JPCP), identifies the significant factors, and provides a predictive model assisting in monitoring and managing the productivity of the JPCP construction process. The completed and progressive projects are employed to derive and assess the proposed model. The results are analyzed to illustrate its capabilities.