• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.594-594
• /
• 2012

Al doped ZnO (AZO) thin films were deposited on textured glass substrate by magnetron sputtering method. Also, AZO films on textured glass were etched by hydrochloric acid (HCl). Average thickness of etched AZO films are 90 nm. We observed morphology of AZO film by AFM with various etchant concentration and etching time. Etched AZO films have low resistivity and high haze. The surface RMS roughness of AZO film was increased from 53.8 nm to 84.5 nm. The haze ratio was also enhanced in above 700 nm of wavelength due to light trapping effect was increased by rough AZO surface. The etched AZO films on textured glass are applicable to fabricate solar cell.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권6호
• /
• pp.814-822
• /
• 2012

선박용 SCR 시스템에서 유동 및 혼합특성을 개선하기 위해 상하유도 및 스월 형상의 혼합기가 고려되었다. 본 연구의 목적은 혼합기 구조에 따른 난류강도 및 균일지수(Uniformity Index)를 상세히 분석하여 SCR 성능을 개선하는 것이다. 그 결과, 촉매부 전단에서의 농도균일도는 혼합기를 사용하였을 경우 약 5% 개선됨을 알 수 있었다. 상하유도형 혼합기의 사용에 따라 주위에서 높은 RMS 수치 및 상대난류강도를 보이지만, 하류로 진행하면서 두 값은 감소하는 경향을 보였다. 스월형 혼합기의 경우 유동의 진행에 대해 RMS 수치와 상대난류강도의 감소가 비교적 적고 상대난류강도의 경우 상대적으로 균일한 분포를 보였다. 두 혼합기에서 발생하는 유동특성에 의해 혼합효과 및 혼합거리가 달랐음을 알 수 있었다.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2003년도 가을 학술논문집
• /
• pp.491-496
• /
• 2003

ICRP-60의 방사선방호 신개념이 국내 법령에 도입됨에 따라 원전 방사성유출물 관리의 변경이 불가피한 실정이다. 방사성유출물 관리의 중요한 요소 중의 하나가 원전 방사선감시계통(Radiation Monitoring System)의 적절한 운용이다. RMS는 원자력법에 명시되어 있는 일반인의 선량한도와 배출관리기준을 만족하도록 운용되어야 한다. 방사성유출물을 제한하는 기준에 따른 RMS 경보설정치의 비교ㆍ분석을 통해 국내 원전에 적용 가능한 최적의 개선방안을 제시할 수 있다. 본 논문에선 선량한도 기준 중 가능한 모든 피폭경로를 고려하여 예상선량률을 계산한 선행 RMS 경보설정 개선방안과의 비교를 위해 주요 피폭경로만 고려하는 선량환산인자에 의한 예상선량률 계산과 RMS 경보설정 개선방안을 조사하였다.

• 분석과학
• /
• 제23권3호
• /
• pp.247-254
• /
• 2010

본 연구는 폐기물분석전문기관이 신뢰성 있는 분석결과를 얻을 수 있도록 하기위한 폴리 염화바이페닐(PCBs) 정도관리 숙련도 평가용 표준물질을 개발할 목적으로 수행하였으며 다음과 같은 결과를 얻었다. PCBs함유 절연유와 PCBs가 함유되지 않은 절연유(PCB free oil)에 PCBs 표준액을 첨가하여 조제한 표준물질로 PCBs에 대한 숙련도평가용 표준물질을 제조하였다. PCBs 표준액 첨가에 의한 균질화도를 검토한 결과, Arochlor 1254 (6 ppm)과 Arochlor 1254:1260(1:1) (5 ppm)을 첨가한 경우 최대 60일, Arochlor 1260 (3.5 ppm)을 첨가한 경우 최대 90일이 지나야 균질화되는 것을 확인할 수 있었다. 제조된 표준물질을 10회 이상 반복 측정한 결과, PCBs 제조 표준물질은 상대표준편차 3.51~5.01%로 균질성이 있다고 판단되었으며, 일원분산분석법(one way ANOVA)에 따라 균질도를 평가한 결과 모든 시료가 균질하다고 판단되었다. 제조된 표준물질을 무작위로 10개의 선정하여 분석한 결과를 기준값으로 선택하였으며, 측정과정과 균질도에 의한 확장불확도값은 0.26~0.49로 조사되었다.

• 대한기계학회논문집B
• /
• 제27권8호
• /
• pp.1089-1096
• /
• 2003

An experiment was performed to investigate lift-off, blow-off and combustion characteristics of a lifted coaxial diffusion flame according to fuel jet and air velocity. A jet diffusion flame which is attached on the nozzle rim begins to be lifted with increase of air velocity, and finally becomes blow-off at higher air velocity. In experiment, blow-off limit increased with increase of fuel jet velocity, however lift-off occurred at lower air velocity. Flame structure and combustion characteristics were examined by schlieren photos, temperature distributions and emission concentration distributions. Flame temperature became higher at midstream and its RMS became larger at up and downstream with increase of air velocity. Local NO concentration decreased but $CO_2$concentration increased with increase of air velocity, which shows combustion reaction becomes close to be stoichiometric at higher air velocity in spite of lift-off.

• 접착 및 계면
• /
• 제13권1호
• /
• pp.24-30
• /
• 2012

폴리아릴레이트(polyarylate, PAR) 섬유의 산 처리와 자외선 조사 처리에 의한 섬유표면의 미세구조 변화를 SEM과 AFM을 통하여 살펴보고 RMS roughness로 분석하였으며, 접촉각 측정을 하였다. 또한, PAR 섬유의 표면개질이 폴리에틸렌 나프탈레이트(polyethylene naphthalate, PEN) 수지와의 계면접착력에 어떠한 영향을 미치는지를 섬유 풀-아웃 시험(Fiber Pull-out)을 통해 분석하였다. 산처리 농도와 자외선 조사 처리 시간이 증가함에 따라 PAR 섬유의 표면에 에칭이나 크랙이 발생하면서 표면의 거칠기가 증가하는 양상을 보였으며, 물에 대한 접촉각은 감소하는 결과를 보였다. PEN 수지와의 계면접착력을 분석한 결과, 산 처리 농도의 증가와 자외선 조사처리 시간이 경과에 따라 증가하였고 특히, 산 처리 농도 pH 3, 자외선 조사 처리시간이 24 h일 때 최대 계면접착력을 보였다. 이는 섬유표면조도의 증가에 따른 섬유 표면적의 증가로, 계면에서 상호작용할 수 있는 면적이 증가하기 때문이라고 볼 수 있다.

• 대한금속재료학회지
• /
• 제48권4호
• /
• pp.363-368
• /
• 2010

N,N'-diphenyl-N,N'-bis(3-methylphenyl)1-1' biphenyl-4,4'-diamine (TPD) hole-transporting layers were deposited using a continuous slot-die coating method on ITO/PET flexible substrates. It is crucial that the substrates have a very smooth surface with a RMS roughness of less than 2 nm for the deposition of semiconductor nanocrystals or Quantum Dots. The parameters of the slot-die coating, including the solution concentration of the TPD, the gap between the slot-die and the substrates, and the coating speed were controlled in these experiments. To obtain full coverage of the TPD films on the ITO/PET substrates (40 mm wide and several meters long), the injection rates of the TPD solution were increased proportional to the coating speed of the flexible substrates. Additionally, the injection rates must be increased as the gap distance changes from 400 to 600 ${\mu}m$ at the same coating speed. A RMS surface roughness of less than 2 nm was obtained, in contrast to bare ITO/PET substrates, at 13 nm, as the coating speed and gap distance increased.

• Nuclear Engineering and Technology
• /
• 제51권2호
• /
• pp.356-368
• /
• 2019

This paper presents the verification and validation (V&V) of the STREAM/RAST-K 2.0 code system for a pressurized water reactor (PWR) analysis. A lattice physics code STREAM and a nodal diffusion code RAST-K 2.0 have been developed by a computational reactor physics and experiment laboratory (CORE) of Ulsan National Institute of Science and Technology (UNIST) for an accurate two-step PWR analysis. The calculation modules of each code were already verified against various benchmark problems, whereas this paper focuses on the V&V of linked code system. Three PWR type reactor cores, OPR-1000, three-loop Westinghouse reactor core, and APR-1400, are selected as V&V target plants. This code system, for verification, is compared against the conventional code systems used for the calculations in nuclear design reports (NDRs) and validated against measured plant data. Compared parameters are as follows: critical boron concentration (CBC), axial shape index (ASI), assembly-wise power distribution, burnup distribution and peaking factors. STREAM/RAST-K 2.0 shows the RMS error of critical boron concentration within 20 ppm, and the RMS error of assembly power within 1.34% for all the cycles of all reactors.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 Proceedings of 2004 Korea-Japan Joint Seminar on Particle Image Velocimetry
• /
• pp.65-74
• /
• 2004

Measurement of concentration distributions of suspended particles in a micro-channel is out of the most crucial necessities in the area of Lab-on-a-chip to be used for various bio-chemical applications. One most feasible way to measure the concentration field in the micro-channel is using micro-LIF(Laser Induced Fluorescence) method. However, an accurate concentration field at a given cross plane in a micro-channel has not been successfully achieved so far due to various limitations in the light illumination and fluorescence signal detection. The present study demonstrates a novel method to provide an ultra thin laser sheet beam having five(5) microns thickness by use of a micro focus laser line generator. The laser sheet beam illuminates an exact plane of concentration measurement field to increase the signal to noise ratio and considerably reduce the depth uncertainty. Nile Blue A was used as fluorescent dye for the present LIF measurement. The enhancement of the fluorescent intensity signals was performed by a solvent mixture of water $(95\%)$ and ethanol (EtOH)/methanol (MeOH) $(5\%)$ mixture. To reduce the rms errors resulted from the CCD electronic noise and other sources, an expansion of grid size was attempted from $1\times1\;to\;3\times3\;or\;5\times5$ pixel data windows and the pertinent signal-to-noise level has been noticeably increased accordingly.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 추계학술대회 논문집
• /
• pp.86-89
• /
• 2004

One most feasible way to measure the concentration field in the micro-channel is using micro-LIF(Laser Induced Fluorescence) method. However, an accurate concentration field at a given cross plane in a micro-channel has not been successfully achieved so far due to various limitations in the light illumination and fluorescence signal detection. The present study demonstrates a novel method to provide an ultra thin laser sheet beam having five(5) microns thickness by use of a micro focus laser line generator. The laser sheet beam illuminates an exact plane of concentration measurement field to increase the signal to noise ratio and considerably reduce the depth uncertainty. Nile Blue A was used as fluorescent dye for the present LIF measurement. The enhancement of the fluorescent intensity signals was performed by a solvent mixture of water $(95\%)$ and ethanol (EtOH)/methanol (MeOH) $(5\%)$ mixture. To reduce the rms errors resulted from the CCD electronic noise and other sources, an expansion of grid size was attempted from $1\times1$ to 3(3 or 5(5 pixel data windows and the pertinent signal-to-noise level has been noticeably increased accordingly.