• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2000년도 유체기계 연구개발 발표회 논문집
• /
• pp.373-378
• /
• 2000

The crevice corrosion of local corrosion occur when the gap exist on metal surface. This crevice corrosion happen to region such as flange of pipe, contact part of casing, under gasket and packing, between valve disk and seat of pump etc. Especially The crevice corrosion of mild steel(SS 400) get serious. This paper was studied on the crevice corrosion of SS 400 in fluid environment. In $0\%,\;2\%,\;3.5\%,\;5\% NaCl$ solution, the aspect of the crevice corrosion and polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 with crevice and non-crevice was measured according to the NaCl concentration. The main results obtained are as follows : 1) Under crevice corrosion, the corrosion potential become less noble as the concentration of NaCl solution increased. 2) The current density under open circuit potential was high drained as concentration of NaCl solution increased by $3.5\%$ but the concentration increased over $3.5\%$, the current density was low drained. 3) The weight loss rate of SS 400 was increased as concentration of NaCl solution Increased by $3.5\%$, but the concentration increased over $3.5\%$, that of SS 400 was decreased. 4) Effect of oxygen for crevice corrosion in the concentration of $3.5\%$ NaCl solution become sensitive than that $0\%$ NaCl solution.

• Korean Chemical Engineering Research
• /
• 제52권3호
• /
• pp.328-334
• /
• 2014

정삼투막 공정을 이용한 소금 및 수크로오스 용액의 처리에서 농도분극현상이 투과유속에 미치는 영향을 검토하였다. 정삼투 공정에서 투과 유속감소는 주로 분리막 표면에서의 농도분극에 기인하며, 분리막의 지지층에서 발생한 내부농도분극에 의한 투과유속 감속이 활성층에서 발생한 외부농도분극에 의한 것 보다 더 컸다. 순수 투과유속은 삼투압이 증가함에 따라 비선형적으로 증가하였다. NaCl 용액의 활성층 배향(DS-AL)에서의 수 투과계수는 $1.8081{\times}10^{-7}m/s{\cdot}atm$, 지지층 배향(DS-SL)의 경우 $1.0957{\times}10^{-7}m/s{\cdot}atm$ 이었으며, 이로부터 산출된 막저항은 각각 $5.5306{\times}10^6s{\cdot}atm/m$, $9.1266{\times}10^6s{\cdot}atm/m$ 이었다. 수크로오스 용액의 경우 활성층 배향(DS-AL)에서의 투과유속이 지지층 배향(DS-SAL)에서의 투과유속보다 1.33~1.90배 크게 나타났다. 삼투압(${\pi}$)에 대한 투과유속(J)의 변화는 전자의 경우 $J=-0.0177+0.4506{\pi}-0.0032{\pi}^2$, 후자의 경우 $J=0.0948+0.3292{\pi}-0.0037{\pi}^2$으로 표현될 수 있었다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.28-31
• /
• 2000

In this paper, the effects of La addition of PLZT(x/30/70) thin films Prepared by sol-gel method are investigated for NVFRAM application. The tetragonality (c/a), the grain size, and the surface roughness of PLZT thin films decrease with an increase of La concentration. As the La concentration increases, the dielectric constants at 10 kHz increase from 450 to 600, while the loss tangent decrease from 0.075 to 0.025. Also, the leakage current density at 100kV/cm decrease from 5.83$\times$10$^{-7}$ to 1.38$\times$10$^{-7}$ 4/$\textrm{cm}^2$. In the results of hysteresis loops measured at $\pm$170kV/cm, the remanent polarization and the coercive field of PLZT thin films with La concentration from 0 to 10㏖％ decrease from 20.8 to 10.5 $\mu$C/cm and from 54.48 to 32.12kV/cm, respectively. After a fatigue measurement by applying 10$^{9}$ square pulses with $\pm$5V, the remanent polarizations of PLZT thin films with 0 and 10㏖％ La concentration decrease about 64 and 42 ％ from initial state. In the results of retention measurement after 10$^{5}$ s, PLZT thin films with 0 to 10mo1％ La concentration show that the remanent polarization is decreased about 43％ and 9％ from initial state, respectively.

• 한국표면공학회지
• /
• 제18권3호
• /
• pp.105-115
• /
• 1985

Lead-tin-copper ternary alloy electrodeposition is conducted onto the inner bore surface of plain bearings as an overlay in order to investigate the effect of slot width, current density and fluoboric acid concentration on the uniformity of overlay. The thickness of overlay is analyzed by means of current distribution resulting from the overvoltage of plating bath and the apparent distance between cathode and anode. The result demonstrate that the uniformity of overlay is remarkably dependent of the slot size and current density, but has little bearing on the fluoboric acid concentration over 100g/L. This present study indicates that uniform overlay is obtainable within the tolerable thickness of ${\pm}2{\mu}m$ by using the slot width of 22mm. The surface morphology examination also shows the important role of concentration polarization of the micro-uniformity of overlay. The micro-uniformity has improved at the low concentration polarization which resulted from operating at the low current density and high fluoboric acid concentration. The surface morphology of deposits exhibits the vivid pyramid crystalline in the plating condition of low concentration polarizatio and all deposits have columnar structure parallel to the applied electric field regardless of the electroplating condition used.

• 한국가스학회지
• /
• 제5권4호
• /
• pp.33-39
• /
• 2001

흡수식냉동기의 작동매체로 사용되고 있는 LiBr수용액 중에서 각 구성재료인 일반구조용 압연강재, 동 및 동합금재인 Ai-Ni bronze의 부식거동에 관한 연구를 하기 위하여, 여러 가지 농도의 LiBr 수용액 중에서 각 재료에 대한 분극실험을 실시하여 부식거동을 고찰한 결과 다음과 같은 결론을 얻었다. 1) 수용액의 LiBr 농도가 증가할수록 각 재료의 분극저항은 낮아지고, 개로전위는 비전 위화되면서 부식전류밀도는 높게 배류된다. 2) 일반구조용 압연강재의 개로전위는 동 및 Al-Ni bronze의 개로전위보다 비전위화되면서 부식전류밀도는 더 높게 배류된다. 3) 동 및 Al-Ni bronze에 대한 $62\%$ LiBr 수용액 중에서의 양극분극은 활성태로 지속되지만, 천연해수 중에서의 양극분극은 활성태가 지속되다가 부동태화전류가 나타난다.

• 한국표면공학회지
• /
• 제54권2호
• /
• pp.71-76
• /
• 2021

Ag925, silver with added copper, is popular alloy due to its low price. However, it has a difficult to use because of the low corrosion resistance. In various alloys, neodymium (Nd) works as an element to improve corrosion resistance by reacting with interstitial elements in the alloy. When 1.5 wt. % Neodymium was added to Ag925, the potential on the activated polarization in a potentiodynamic polarization test was increased from -0.15 V to -0.05 V. Ag925 with added neodymium showed the passivation after activation polarization. But When the potential increased around 50 mV, the current density is increased to 3 × 10-3. Ag925 with the 1.5 wt. % Nd had the low corrosion rate.

• 한국자기공명학회논문지
• /
• 제23권3호
• /
• pp.81-86
• /
• 2019

Overhauser dynamic nuclear polarization (O-DNP) has been an efficient method to boost the thermal nuclear polarization in liquids at room temperature. However, O-DNP for a benchtop NMR using a permanent magnet has remained unexplored yet. In this work, we report the development of an O-DNP system adopting a permanent magnet of 1.6 T. Q-band (~43 GHz) high-power amplifier produced 6 W microwave for saturation. Instead of resonator, we used an open-type antenna for the microwave irradiation. For several representative small molecules, we measured the concentration and frequency dependences of the enhancement factor. This work paves the way for the development of a benchtop DNP-NMR system overcoming its disadvantage of low quality signal when using a permanent magnet.

• 전기화학회지
• /
• 제4권4호
• /
• pp.160-165
• /
• 2001

황산원자를 포함하는 mercapto화합물은 도금시 전착속도를 증가시키는 첨가제로 알려져 있는데, 이 중 4가지의 mercapto 화합물을 선정하여 농도를 변화시켜가며 Hull cell test, Haring-Blum cell test, cathodic polarization, EQCM(Electrochemical Quartz Crystal Microbalance)등을 이용하여 도금특성 및 throwing power를 알아보았다. Cathode polarization 및 EQCM을 통한 구리 전착량을 알아본 결과 4가지의 mercapto 화합물 중 3-mercapto-1-propanesulfonic acid가 activator로서 가장 적당하였으며, 그 농도가 20 ppm에서 throwing power를 증가시키고, 농도 및 활성 과전압이 오직 $Cl^-$만 포함되었을 때보다 cathodic scan시 100 mV 만큼 shift되어 증착속도를 증가시킴을 알 수 있었다.

• 방사성폐기물학회지
• /
• 제18권1호
• /
• pp.1-18
• /
• 2020

Molten salt solutions consisting of eutectic LiCl-KCl and concentrations of samarium chloride (0.5 to 3.0 wt%) at 500℃ were analyzed using both cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The CV technique gave the average diffusion coefficient for Sm³⁺ over the concentration range. Equipped with Sm³⁺ diffusion coefficient, the Randles-Sevcik equation predicted Sm³⁺ concentration values that agree with the given experimental values. From CV measurements; the anodic, cathodic, and half-peak potentials were identified and subsequently used as a parameter to acquire EIS spectra. A six-element Voigt model was used to model the EIS data in terms of resistance-time constant pairs. The lowest resistances were observed at the half-peak potential with the associated resistance-time constant pairs characterizing the reversible reaction between Sm³⁺ and Sm²⁺. By extrapolation, the Voigt model estimated the polarization resistance and established a polarization resistance-concentration relationship.

• Journal of Advanced Marine Engineering and Technology
• /
• 제13권2호
• /
• pp.43-63
• /
• 1989

Various kinds of corrosion prevention methods have been developed. It is known that the method of electrochemical protection is more effective and economical than any other method on the large scale metal structures in corrosive solutions. Strong acid solutions such as nitric and sulfuric acid solutions are often used in industries, and the expensive stainless steel is almost exclusively used for the equipment that comes in contact with such acid solutions. However, it is more reasonable that carbon steel is used rather than stainless steel depending upon concentration of those acid solutions from the economical viewpoint. In this study, the typical strong acid solution such as nitric and sulfuric acid solutions are chosen for the experiment and the selected materials of specimen are the stainless steels of SUS 304L and SUS 316L, the carbon steels of SS 41, SM 50 and RA 32, and highly pure lead. Electrochemical protection diagrams can be drawn with data from the external cathodic and anodic polarization curves of SUS 304L, SUS 316L and SM 50 steels in 5-60% nitric acid solutions and from those polarization curves of SS 41, RA 32, SM 50 and SUS 316L steels, and highly pure lead in 2.5-98% sulfuric acid solutions at the slow scanning rate. The data obtained with using the determination method of the optimum cathodic protection potential, the Tafel extrapolation method and the characteristics of anodic polarization curves. The main results obtained from the diagrams are as follows: 1) In nitric acid solution : (1) Corrosion potentials exist in each of those corrosion zones on the stainless steels in the lower concentration than about 12% solutions and on the high tensile strength steels in the lower concentration than about 30% solutions, but the corrosion current (density) in each zone is small on the above mentioned former steels and large on the latter ones. (2) The stainless steels can be self-passivated in the higher concentration than 15% solutions, and the high tensile strength steels gives rise to the same phenomenon in the higher concentration than 35% solutions. (3) The stainless steels in the lower concentration than 60% solutions and the high tensile strength steels in the higher concentration than 35% solutions can be used without protection, but the latter steels must ve protected anodically in the lower conccentration than about 30% solutions. 2) In sufuric acid solution : (1) The carbon steels can be self-passivated in the higher concentration than 45% solutions, and the SUS 316L steel in higher concentration than 75% solutions and the lead in all concentration solutions also gives rise to the same phenomenon. (2) The lead in the lower concentration than 80% solutions and the SUS 316L steel in the higher concentration than 80% solutions can be used without protection. (3) The carbon steels in the higher concentration than 50% solutions also can be used without protecting economically, but the SUS 316L steel in the 20-70% solutions are considerably corrosive without protecting anodically.