• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.305-307
• /
• 2010

In this study, we develop a method to achieve heat transfer enhancement inside a square duct with high aspect ratio without changing any inner structures. Especially, a method to lower the possible maximum temperature is suggested if constant heat flux is provided to single surface of square duct. Knowing the fact that heat transfer rate is inversely proportional to flow area, we proposed tapered channel concept which uses narrower gap toward the flow exit where the maximum temperature is expected. To maintain equivalent power consumption, inlet section has been enlarged. To verify the proposed concept, experimental tests have been performed.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.413-414
• /
• 2008

Abstract should be in English. The leaning angle optimization of turbine blade using the genetic algorithm was conducted in this paper. The calculation CFD technique was based upon the Diagonalized Alternating Directional Implicit scheme(DADI) with algebraic turbulencemodeling. The leaning angle of VKI turbine blade was represented using B-spline curve. The control points are the design variable. Genetic algorithm was taken into account as an optimization tool. The objective was to minimize the total pressure loss. The optimized final geometry shows the better aerodynamic performance compared with the initial turbine blade.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제20회 춘계학술대회 논문집
• /
• pp.197-200
• /
• 2003

Plows in the LOX manifold with two different types of predistributor have been analyzed using a CAE technique. The computational geometry and flow condition through the injection holes resemble those in the actual manifold of the liquid rocket, so that the results can describe the actual flow reasonably It is noted that two different types of predistributors lead to very similar pressure and mass distributions in the plane just above the injection holes. Also the pressure drop across the injection holes is rather uniform regardless of location of the holes and this would suggest that the simplified modeling of the flow through the injection holes is possible from an engineering point of view.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.30-32
• /
• 2001

There are many difficult problems in analyzing the flow characteristics in a high voltage circuit breaker such as shock wave and complex geometries, which may be either static or in relative motion. Although a variety of mesh generation techniques are now available, the generation of meshes around complicated, multi-component geometries like a gas circuit breaker is still a tedious and difficult task for the computational fluid dynamics. This paper presents the CFD program for analyzing the compressible flow fields in a high voltage gas circuit breaker using the Cartesian cut-cell method based on the CFD-CAD integration, which can achieve the accurate representation of the geometry designed by a CAD tools. This technique is frequently satisfied, and it will be almost universally so in the future, as the CFD-CAD traffic increase.

• Nuclear Engineering and Technology
• /
• 제52권2호
• /
• pp.223-229
• /
• 2020

The present work proposes a solution to the static Boltzmann transport equation approximated by the simplified P₃ (SP₃) on angular, and the analytic coarse mesh finite difference (ACMFD) for spatial variables. Multi-group SP₃-ACMFD equations in 3D rectangular geometry are solved using the GMRES solution technique. As the core time dependent analysis necessitates the solution of an eigenvalue problem for an initial condition, this work is hence devoted to development and verification of the proposed static SP₃-ACMFD solver. A 3D multi-group static diffusion solver is also developed as a byproduct of this work to assess the improvement achieved using the SP₃ technique. Static results are then compared against transport benchmarks to assess the proximity of SP₃-ACMFD solutions to their full transport peers. Results prove that the approach can be considered as an acceptable interim approximation with outputs superior to the diffusion method, close to the transport results, and with the computational costs less than the full transport approach. The work would be further generalized to time dependent solutions in Part II.

• 소성∙가공
• /
• 제9권6호
• /
• pp.653-662
• /
• 2000

Wrinkling is one of the major defects in sheet metal products together with tearing, springback and other geometric and surface defects. The initiation and growth of wrinkles are influenced by many factors such as stress ratios, mechanical properties of the sheet material, geometry of the workpiece, contact condition, etc. It is difficult to analyze the wrinkling initiation and growth considering all the factors because the effects of the factors are very complex and the wrinkling behavior may show a wide scatter of data even for small deviations of factors. The finite element analyses of the wrinkling initiation and growth in the sheet metal forming process provide the detailed information about the wrinkling behavior of sheet metal. The direct analyses of the wrinkling initiation and growth, however, bring about a little difficulty in complex industrial problems because it needs large memory size and long computation time. In the present study, therefore, a global-local analysis technique is introduced for the computational efficiency. Through the analysis of wrinkling in the door inner stamping process, the efficiency of the global-local analysis technique is investigated.

• Structural Engineering and Mechanics
• /
• 제38권2호
• /
• pp.171-193
• /
• 2011

One of the possible alternatives of simulation-based time-dependent reliability assessment of pre-stressed biconcave and biconvex cable trusses, the Monte Carlo method, is applied in this paper. The influence of an excessive deflection of cable truss (caused by creep of cables and rheologic changes) on its time-dependent serviceability is investigated. Attention is given to the definition of the basic random variables and their statistical functions (basic, mutually dependent random variables such as the pre-stressing forces of the bottom and top cable, structural geometry, the Young's modulus of elasticity of the cables, and the independent variables, such as permanent load, wind, snow and thermal actions). Then, the determination of the response of the cable truss to the loading effects, and the definition of the limiting values considering serviceability of the structure are performed. The potential of the method, using direct Monte Carlo technique for simulation-based time-dependent reliability assessment as a powerful tool, is emphasized. Results obtained by the First order reliability method (FORM) are compared with those obtained by the Monte Carlo simulation technique.

• Structural Engineering and Mechanics
• /
• 제17권6호
• /
• pp.789-817
• /
• 2004

This paper deals with the modal analysis of rotational shell structures by means of the numerical solution technique known as the Generalized Differential Quadrature (G. D. Q.) method. The treatment is conducted within the Reissner first order shear deformation theory (F. S. D. T.) for linearly elastic isotropic shells. Starting from a non-linear formulation, the compatibility equations via Principle of Virtual Works are obtained, for the general shell structure, given the internal equilibrium equations in terms of stress resultants and couples. These equations are subsequently linearized and specialized for the rotational geometry, expanding all problem variables in a partial Fourier series, with respect to the longitudinal coordinate. The procedure leads to the fundamental system of dynamic equilibrium equations in terms of the reference surface kinematic harmonic components. Finally, a one-dimensional problem, by means of a set of five ordinary differential equations, in which the only spatial coordinate appearing is the one along meridians, is obtained. This can be conveniently solved using an appropriate G. D. Q. method in meridional direction, yielding accurate results with an extremely low computational cost and not using the so-called "delta-point" technique.

• Journal of Computational Design and Engineering
• /
• 제3권4호
• /
• pp.337-348
• /
• 2016

An experimental approach is presented for the measurement of wear that is common in the threading of cold-forged steel. In this work, the first objective is to measure wear on various types of roll taps manufactured to tapping holes in microalloyed HR45 steel. Different geometries and levels of wear are tested and measured. Taking their geometry as the critical factor, the types of forming tap with the least wear and the best performance are identified. Abrasive wear was observed on the forming lobes. A higher number of lobes in the chamber zone and around the nominal diameter meant a more uniform load distribution and a more gradual forming process. A second objective is to identify the most accurate data-mining technique for the prediction of form-tap wear. Different data-mining techniques are tested to select the most accurate one: from standard versions such as Multilayer Perceptrons, Support Vector Machines and Regression Trees to the most recent ones such as Rotation Forest ensembles and Iterated Bagging ensembles. The best results were obtained with ensembles of Rotation Forest with unpruned Regression Trees as base regressors that reduced the RMS error of the best-tested baseline technique for the lower length output by 33%, and Additive Regression with unpruned M5P as base regressors that reduced the RMS errors of the linear fit for the upper and total lengths by 25% and 39%, respectively. However, the lower length was statistically more difficult to model in Additive Regression than in Rotation Forest. Rotation Forest with unpruned Regression Trees as base regressors therefore appeared to be the most suitable regressor for the modeling of this industrial problem.

• 한국산학기술학회논문지
• /
• 제19권1호
• /
• pp.672-679
• /
• 2018

본 논문은 최적설계 시스템을 이용한 형상설계 방법론에 대해 설명하고 있으며, 일반적으로 3차원 해석은 설계를 위해 반드시 필요하다. 퍼지지식처리 수법과 계산기하학적 기법에 바탕을 둔 자동화된 유한요소 메쉬 생성 기법은 상용화된 유한요소해석코드와 솔리드모델러와 함께 시스템에 결합되어 있다. 또한, 다층형 신경망의 도움과 함께 개발된 시스템은 다차원 설계변수 공간에 존재하는 여러 만족하는 설계해인 디자인윈도우를 얻을 수 있게 해준다. 개발된 최적화 설계 시스템 사용된 부품을 평가하는데 성공적으로 적용하였다. 사이드 하우징 브라켓을 현장에서 사용되어지는 굴삭기의 힘과 유압브레이커의 작용하는 응력을 응력 게이지로 사이드 하우징 브라켓의 크랙 발생부위에 부착하여 최대응력이 얼마나 걸리는지를 측정하였다. 적용하는 대상을 현장에서와 동일한 조건하에서 최대응력이 허용응력보다 같거나 적게 하고, 기존형상 유지, 재질은 SM490, 중량 최소화 안전계수는 3으로 하여, 최대응력 값에 대한 해석을 수행하였다. 구조가 비교적 간단한 36톤용 사이드 하우징 브라켓을 최적화하였지만, 다른 클래스의(톤수 별) 사이드 하우징 브라켓 적용 시 품질향상에 크게 기여하리라 생각된다.